|
|
We offer three main versions of our Digital Probe
• Spring Push
• Pneumatic Push
• Feather Touch
The Probe is an absolute measuring device that delivers accurate results when switched on, regardless of any 'OFF' movements.
|
|
• Measuring Range 0.5 mm
• Resolution Programmable to <0.01 µm
• Tip Forces down to 5 g
• Excellent Repeatability
• Up to 3906 Readings/Second
• Industry Standard Styli
• Compact Size
• Direct Reading in mm/inch
Solartron's new Digital Lever Probe has been conceived for the precision measurement market. This probe is ideally suited to applications where the use of axial measuring probes is not possible, and where a low tip force and a high number of probing points are required. Its simple design and exceptional reliability result in a reduced cost of ownership without any reduction in performance.
|
|
Digital Outside Micrometer - 201 Series
Protected to IP54 specifications
Rugged steel design
Large LCD display
Absolute and Incremental modes
Carbide Measuring faces
Ball attachment included
|
|
|
|
|
|
Model 49-5X is a precision micrometer for measuring thickness of sheet materials such as Textiles, Fabrics and Non-wovens. A selection of pressure feet is available to meet a variety of standards requirements. The unit also incorporates a unique cantilever system to vary the pressure exerted on the sample by adding or removing weights. Pressure foot speed and dwell time are controlled to insure accurate and repeatable test results.
APPLICATIONS
Paper, Paperboard, Corrugated, Cloth, Plastic, Rubber, Plastic Film, Textile Fabrics, Non-wovens, Felts, Geomaterials, Floor Coverings, Leathers and Wipes.
SPECIFICATIONS
(49-50) (49-52)
Range: 0 to 2 mm 0 to 20 mm
Resolution: 0.001 mm* 0.01 mm*
Accuracy: ±0.0025 mm
up to 1.25 mm ±0.025 mm
Repeatability: 0.1% of range
Operating Temp. +20°C to +30°C
*Resolution increased by a factor of ten to 0.1μm (for 49-50) and to 1.0μm (for 49-52)
FEATURES
* Large LCD display
* Electronic compensation minimizes displacement transducer non-linearity
* Rigid cast aluminum base assures thermal and mechanical stability
* Foot switch allows hands-free operation of test button
* RS-232 data output
* Range: 0 to 2 mm and 0 to 20 mm
* Resolution: 0.001 mm*
* Accuracy: ±0.0025 mm up to 1.25 mm
* Repeatability: 0.1% of range
* Operating temperature: +20°C to +30°C
|
|
TMI 49-70 and 49-72 Series Micrometers provide the precision necessary for the critical thickness measurement of numerous sheet materials.
APPLICATIONS
Films, Foils, Tissue, Papers, Corrugated, Paperboard, Plastics, Felt, Rubber, Fiberboard, Carton board
SPECIFICATIONS
* Range of measurement:Model 49-70: 0.0 to 1.270 x .003 mm;(0.0 to 0.050 x .0001 in.)
* Range of measurement:Model 49-72: 0.0 to 12.70 x .03 mm;(0.0 to 0.5 x .001 in.)
* Standard anvil diameter 16 mm (0.63 in.)
* Load: 7.3 psi (50.4 kPa)
FEATURES
* Digital display
* Dual range (Imperial or Metric)
* Motorized automatic cycling
* 5-second test cycle
* Special anvil diameters and dead weight loads available upon request
* Calibrated gauge blocks are available to meet your needs
|
|
|
Micrometer for external measurements with digital reading. Frame in steel. Hardened screw and contact surfaces in carbide. Direct mm./inch conversion. Set to zero in any position. Serial number. Manufactured as per DIN 863/1. Supplied in case.
|
|
A micrometer sometimes known as a micrometer screw gauge, is a device used widely in mechanical engineering and machining for precisely measuring, along with other metrological instruments such as dial calipers and vernier calipers. Micrometers are often, but not always, in the form of calipers. Shop for WESTport Calipers
There are five common types of micrometers; the names are based on their application:
- Outside micrometer- (aka micrometer caliper), typically used to measure wires, spheres, shafts and blocks.
- Inside micrometer- used to measure the diameter of holes.
- Depth micrometer- measures depths of slots and steps.
- Bore micrometer- a 3 -anvil head on a micrometer base used to accurately measure inside diameters.
- Tube micrometer- used to measure the thickness of tubes.
|
|
The Baty digital micrometer
* IP54 protection level can be used when exposed to coolant water, dust and oil
* Large LCD
* Inch-metric and zero setting
* SPC output
* Friction thimble
* Chrome plated frame
* Carbide tips
* Resolution 0.001mm (0.00005")
* Automatic power off
* Easy one handed use
* Heat insulated frame
|
|
MarConnect data output (choose between USB, Opto RS232C or Digimatic)
Ratchet integrated in thimble
Large, easy to read display
|
|
• 0.5 mm Total Measurement Range
• Resolution Programmable to < 0.01 µm
• Simple Installation and Sensor Change
• Excellent Repeatability and Robustness in two planes
• Suitable for Operation in Bores with key slot
• Very Compact Size
• Changeable Tips
• Up to 3,906 Readings/Second
• IP65 Protection
• Traceable Calibration
• CE Marked
The Solartron Digital Mini Probe is a compact, low profile, transducer intended for measurements in confined spaces such as bores. The product is based on a parallel spring structure that is significantly more robust than a single leaf arrangement. This greatly improves the reliability of the sensor, extending its working life and allowing it to be used in more demanding applications, such as automatic gages. The parallel spring also ensures a high level of repeatability, both on axis and across axis, so that it can be used in dynamic applications where profiling is required.
|
|
Slim Type ABS Digimatic Indicator ID-N/ID-B:
- Slim 35 mm wide body greatly enhances application range.
- Various features including waterproofness, display inversion, and back plunger.
ABS Digimatic Indicator IDS: Simplified economy type with a single function.
ABS Digimatic Indicator IDU: Single-function, economy type with a measuring range of 25.4 mm.
ABS Digimatic Indicator IDC:
- Widely used as a general-purpose, multifunction indicator
- Model provided with various measuring ranges, measuring forces, etc.
|
|
Digitronic Indicator - 405 Series
Direct Inch / Metric conversion
58mm dial face
Lugback and 8mm stem mountings
Resolution 0.01m/0.0005"
Absolute / Incremental reading
Floating Zero
|
|
|
The Gauge Buster Load, Stress and Load Rate Indicator is designed to replace dial gauges on materials testing machines. Features include an industry first Auto-Test-Reset mode for hands free operation, bar graph load rate display, permanent storage of test results and easy transfer of results into data base programs. The Gauge Buster LP offers all of the features of the standard Gauge Buster plus the addition of a second digital encoder input for measuring piston/crosshead travel. During each test, the Gauge Buster records load, displacement, time data and can be configured to display piston/crosshead travel rate. After each test has completed, the recorded data (XY data and results) can be downloaded to a PC with ADMET’s WinCOM/WinCOM Plus Data Communications Program for further review and analysis. The Gauge Buster LP is sometimes used for soil/asphalt compaction.
|
|
Digital Indicators
* Inch / metric
0-12.7mm (0-0.5") measuring range
0.001mm (0.00005") resolution
* Zero / on / off
Zero setting at any position / manual
power on / off
Rotating bezel – 330 degrees
* Data hold
* TOL Set tolerance for pass / fail indication
* ABS Switch between absolute and incremental mode
* Universal 8mm stem mount
* Supplied with 3mm diameter steel ball contact
|
|
MarCator Digital and Dial Indicators
MarCator Indicators are available as Digital or Dial versions. From the classic dial indicator to the newest digital indicators, Mahr offers the best solution for every measuring task.
MarCator Digital Indicator 1075
- Large, easy to read display
- MarConnect data output, select any one of the following interfaces: USB, Opto RS232C or Digimatic
- Protection class IP51
|
|
Digital Indicators
Easy to operate, high-accuracy digital indicator available in a wide measuring range
- High accuracy:
± 1 µm(U12B/30B)
± 1.5 µm (U60B
- High resolution: 1 µm
- Measuring range: 0 to 60 mm (0 to 2.36")
- Connectable to a personal computer through RS-232C interface
- Peak hold for measuring max./min. and peak to peak values
- Power supply by AC adaptor or battery pack
- The spindle contains a damper mechanism to protect measured objects from damage (U30B and U60B)
- Inch/metric display
|
|
Technical caracteristics
To DIN 878.
- Measuring range 0-12.5 mm.
- Accuracy 0.001 mm.
- mm/inch conversion.
- 6 mm LCD display.
- Clamping stem (8 mm dia.)
- Interchangeable M2.5 contact points.
- Display pivots through 270°.
- Floating zero.
- Zero set at any position.
- Allows measurements to be made using 2 separate references.
- Measurement memorisation (display hold).
- RS 232 connection - For transmitting reading to a statistical processing system.
- Supplied with a FACOM certificate of conformity.
: 213 g.
|
|
GT2 series Digital Contact Sensor
General Purpose Digital Contact Sensor with Push Button Calibration
For full details, download the PRODUCT CATALOG using the CATALOG icon in the Online Support and Services box above
|
|
Brass Thickness Gage
Plastic Thickness Gage Assortments
Stainless Steel Thickness Gage
Steel Feeler Gage - Decimal Thicknesses
Steel Feeler Gage - Metric Thicknesses
|
|
General description
- Universal bore gauge for indicating bore gauging
- Modular design system with extensive range of accessories, enables gauging of most bores.
- Application range: Ø 0.47 mm to 41.3 mm/0.02" to 1.6" (in 3-point version up to 150 mm/5.9")
- Calibration in setting master
- Styles for blind bores (FB) and parallel distances (PA) included in standard programme
- Special designs on request
- Setting rings according to DIATEST company standard or to DIN 2250-C in standard programme
|
|
The GapGun is ideal for use in automotive, aerospace, white goods and transport industries. Gap Gun customers now also include automotive tier 1 applications, and the majority of leading aerospace companies.
The Gap Gun can be used:
Handheld, for offline or production line applications
Robot mounted or inline, using the same measurement head
The Gap Gun is extremely easy and fast to use, and measurement is fully automatic. Simply pull the trigger and move into range.
Contact sales@third.com for more information and a product specification,
or see our list of authorised distributors.
GapGun - Save Time, Save Money, Increase Accuracy
|
|
EDIXIA proposes a wide range of inspection solutions at each step of the assembly process of vehicles or their sub-assemblies:
GapRange gap and flush measurement
GeoRange for vehicle geometry
According to the constraints of the automotive production line, these products are declined in more or less flexible and dynamic version.
Major benefits
-Productivity gains
-Improvement of perceived quality of your vehicles
-Rationalization of your excellence guarantee tools 100% and contact less inspection
Reliable measurements with a high repeatability
1 unique system to analyze all points
Discover our products
GapRange
GeoRange
|
|
Rectangular Guage Block:
- Practical master gage for dimensional measurement
- Two types of steel and ceramic gauge blocks are available.
- Four classes of Class K, Class 0, Class1 and Class 2
Long Size Gauge Block Accessory Sets BMX-S1:
- Accessories for gauge blocks with a nominal size of 125 mm or more
- Used to create the masters of height and size.
- A scriber is also available.
Square Gauge Block:
- 24.1 x 24.1 square gauge block
- Three classes of Class 0, Class 1, and Class 2
- Absolute wringing using the hole
|
|
Composition of parallel gauge blocks in top-quality non-deformable steel. Supplied in case, serial number on each block. Manufactured as per DIN 861. Three different grades are available:
Gr. 0: suitable for metrology rooms and as references for checking other blocks.
Gr. 1: suitable for checking and calibrating measuring instruments.
Gr. 2: suitable for checking production and setting measuring instruments.
Blocks of different dimensions and at any quality are available upon requirement.
|
|
Application
- As comparison reference and utilization standards in the field of length measurement
- For checking gages and measuring instruments
- For setting devices of all types designed for length measurement and in particular their displays
Accuracy
- The manufacturing process is based on DIN EN ISO 3650. Mahr gage blocks are produced with the utmost care.
|
|
The instruments of the type VM have a guiding profile, with which the dimension over balls can be established quickly and reliably, without rocking. The guiding profile is matched with that of the profile of the test item.
The VM inspection instruments display in this series their professionalism. They are robust, simple and with regard to accuracy independent of the operator. The range of VM instruments covers simple hand held devices, through to longitudinal dynamic inspection systems and fully automated FAPP systems. A UPM-certificate specifies the measuring uncertainty of the instrument and enables determination of the measuring uncertainty during usage.
|
|
Internal gear gauges (IV)
For gauging of measurement between balls (Mi)
Constructed in the same way as the split-ball and plunger probe system
Application range: Mi = 3.5 mm up to 333 mm/ 0.14" to 13"
Measuring range: 0.6 mm to 1.6 mm for split-ball system (Mi = 3.5 mm to 26.1 mm/0.14" to 1.03") 3 mm for plunger probe system (Mi = 26.1 mm to 333 mm/ 1.03" to 13")
Split-ball and plunger probe accessories can be applied
Tungsten carbide measuring balls
Special designs and gauge slides on request
External gear gauges (AV)
For gauging of measurement across balls (Ma)
Application range: Ma = 10 mm to 140 mm/0.4" to 5.5"
Measuring range: 30 mm/1.2"
Tungsten carbide measuring balls
For use in MST-102 measuring stand
|
|
Digimatic Height Gage:
- High-efficiency height measurement with the optional dedicated probe
- Measuring range: up to 1000 mm with 3 models
- Universal type that places emphasis on the ease of operation.
- Measuring range: up to 1000 mm with 3 models
ABS Digimatic Height Gage HDS:
- Provided with the ABS function of well-established rotation drive handle.
- Measuring range: up to 600 mm with 2 models
Square column with the ABS function
- Measuring range: up to 1000 mm with 2 models
Standard Height Gage:
- Universal type of square column height gages
- Measuring range: up to 1500 mm with 5 models
|
|
Digitronic Height Gauge - 196 Series
Heavy duty square twin beams
Handwheel for ease of use
ABS/INC measurement
Large LCD display
Inch/mm conversion
Positive lock carbide scriber
Includes indicator holding bar
Supplied in moulded case
|
|
Code: Art. 32/110
Digital height gauge
Digital height gauge in hardened stainless steel. 5 figures liquid crystal display with minus sign. State-of-the-art technology. Slider with micrometric adjustment. Scribing point with widia tip. Manual on/off button. Set to zero in any position. Preset values keys. RS232C data output. Inch/mm conversion. Serial number. Manufactured as per DIN 862.
|
|
|
|
Metrology equipment
