|
|
| Products 121 to 150 of 286 |
Champion Dessicant Dryers
CDT Series
Heatless Desiccant Compressed Air Dryers For pressure dew points of +38°F to -100°F, (+3°C to -73°C)
Basic Controller:
* The basic controller presents a traditional heatless drying
system.
* Using a simple timer based controller, it offers a reliable
fixed cycle operation.
* Automatic time controlled bed regeneration cycles offer
consistent performance.
* The controller LEDs reflect: power on, left tower drying,
right tower drying.
Standard Controller Features:
* Four dew point selections
* State-of-the-art Controller
* Purge Optimizer
* Programable shut-down capabilities
* Dew point performance per ISO 8573.1
|
|
Clean Air System
- Removes water vapor at the point of use
- Desiccant changes color when it needs to be change or recharged
- Outlet screen keeps desiccant particles out of tools
- Oil Removal filter removes 99.9 % of all oil aerosols
- Easy Maintenance
|
|
BD : "The industry benchmark for desiccant dryers"
Incorporating unique, patented technological innovations and extra energy-saving options, Atlas Copco's BD desiccant dryers provide you with the clean, dry air you are in need of to expand the life of your equipment and ensure the quality of your end product.
- Dry air at any time
- Supreme energy efficiency
- Easy installation, Complete design, Plug & Play
- Advanced Control & Monitoring Solutions
- The Reliable choice
- Proven Peace of Mind
- Built for Endurance
|
|
* Atmospheric Dew Points as Low as -100°F
* No Electrical Connection Necessary
* Twin Units Available for Double Service Life
* Color change of the Desiccant provides an instant status of the Compressed Air System
|
|
|
It is globally recognised that condensate from oil-injected compressors is an oil-water emulsion, classified as oil residue and must not be drained into the sewage system nor into the environment. Legislation, worldwide, has become more and more stringent as to the disposal of this oily waste water.
|
|
It is globally recognised that condensate from oil-injected compressors is an oil-water emulsion, classified as oil residue and must not be drained into the sewage system nor into the environment. Legislation, worldwide, has become more and more stringent as to the disposal of this oily waste water.
With the introduction of the OSM 500 and 900 oil-water separators, with the latest filter membrane technology, Atlas Copco offers a most cost effective, safe, environmentally friendly and simple system to handle condensate from oil-injected compressors, fully in compliance with governmental regulations.
|
|
The range of EWD electronically controlled condensate drains is synonymous with safe, dependable and economical condensate management.
The intelligent drain function monitors condensate build-up with liquid level sensors and evacuates the condensate only when necessary, thus avoiding wastage of compressed air and giving considerable energy savings.
The EWD drain device offers security and confidence, enabling you to solve all condensate discharge problems even with heavily contaminated systems.
A wide range of different EWD drains is available for oil contaminated condensate and may also be provided with additional hard coating for use with oil-free and aggressive condensate.
|
|
The range of EWD electronically controlled condensate drains is synonymous with safe, dependable and economical condensate management.
The intelligent drain function monitors condensate build-up with liquid level sensors and evacuates the condensate only when necessary, thus avoiding wastage of compressed air and giving considerable energy savings.
The EWD drain device offers security and confidence, enabling you to solve all condensate discharge problems even with heavily contaminated systems.
A wide range of different EWD drains is available for oil contaminated condensate and may also be provided with additional hard coating for use with oil-free and aggressive condensate.
|
|
|
|
|
|
|
Especially suited for use with Airpot actuators and Airpel cylinders where low friction/low hysteresis, sensitive response, long life, clean operation, and extreme temperature are critical requirements. Offered in both compact and standard configurations for moderate and high flow, Airpot FFR systems are available with standard or precision regulators for precise control and sensitivity. Airpot FFR systems are composed of lightweight aluminum/resin hybrid material built into a compact and modular 40mm x 40mm envelope per component (compact series). Standard and Precision series (with increased low pressure sensitivity) regulators are available; all with hand adjustability and single push lock operation. The precision series offers a pressure range of 0.005 to 0.4 MPa and sensitivity within 0.1% of the full scale. Port connections are available with NPT or G metric threads. Each system is equipped with dual filtration modules that remove particles, dust, oil, moisture and mist down to 0.01 micron. This two stage filtration system is comprised of a 5 micron dust and moisture filter augmented by a 0.01 micron coalescing filter. The long life media transitions from a coarse outer surface to a fine interior structure to reduce clogging prolong life and prevent rust formation. All filters boast a standard corrosion resistant filter bowl guard, one quarter turn filter element removal and a unique O ring slip prevention design. FFR gauges offer highly visible color zone indicators, field adjustable limit marks, flat face design with a non- protruding (standard series, compact and high flow types) gauge embedded in the module made to JIS3 grade with either MPa or PSI readings.
|
|
|
Fisher Controls, Regulator Division is requesting the return of regulators per the July 10, 2007 IMPORTANT SAFETY NOTICE--REGULATOR RETURN. The regulators to be returned are the Type/Series HSR, 67C, 67CR, 67CF, 67CFR, and R622.
|
|
General Description
316 stainless steel for the offshore, food, pharmaceutical and allied industries. A combination unit for filtration and pressure regulation of compressed air for use in these industries.
- 316 Stainless steel throughout. Large flow paths minimise pressure drop. Integral mounting holes.
- Tagging facility built in.
- Filter Unit
Operating Fluids:
- Gases
Filtered lubricated or non-lubricated air, inert gas, sweet (natural) gases. Sour gas option available
- Liquids
Low pressure hydraulic, mineral oil or water.
|
|
The Kavair series of Air Line Equipment incorporates a wide range of standard products such as filters, regulators, lubricators and modular combination units. These products are complemented by ancillary equipment including soft start valves, external autodrain units and condensate valves.
Type F Series Standard Filter
G1/4 G3/8 G1/2
800 - 3500 l/min @ 6 bar
These conventional filters can be used individually or in conjunction with combination air preparation units (FRLs).
Type R Series Regulator
G1/4 G3/8 G1/2
600 - 4000 l/min @ 6 bar
These conventional pressure regulators can be used individually or in conjunction with combination air preparation units (FRLs).
|
|
Filter/Regulator Products
B08
Features
• Space-Saving Integral Filter / Regulator Design
• Unique Flush-mounted Pressure Gauge Available
• Balanced Valve Design
• Modern Design and Appearance
• Light Weight
• High Flow Capacities
• Quick-Disconnect Bowl / Bowl Guard
B12
Features
• Space Saving Package Offers Both Filter and
Regulator Features for Optimal Performance
• Excellent Water Removal Efficiency
• Rolling Diaphragm for Extended Life
• Removable Non-rising Knob for Tamper Resistance
• Quick Response, and Accurate Pressure Regulation
Regardless of Changing Flow or Inlet Pressure
• 5 Micron Standard
|
|
The FRL range is a complete line of components for the treatment of the compressed-air.
FILTER: Thread from 1/8 to 1". Filtration Grade from 5µm to 50µm. Maximum Pressure 15 bar.
REGULATOR: Thread from 1/8 to 1". Regulation Range from 0-2 to 0-12 bar. Max. Pressure 15 bar.
FILTER REGULATOR: Thread from 1/8 to 1''. Regulation Range from 0-2 to 0-12 bar. Filtration Grade from 5µm to 50µm. Max. Presssure 15 bar.
Condensate Exhaust System: Semi automatic - Manual or Automatic to vacuum-operated.
QUICK EXHAUST REGULATOR: Thread 1/8-1/4. Regulation Range from 0-2 to 0-12 bar. Max. Pressure 15 bar.
LUBRICATOR: Thread from 1/8 to 1''. Max. Pressure 15 bar. Oil Loading System: Manual or Automatic to vaccum-operated.
SHOT OFF VALVE: Thread from 1/8 to 1''. Max Pressure 15 bar. Drive System Manual, Pneumatic, Electropneumatic.
SOFT START VALVE: Thread from 1/8 to 1''. Max. Inlet Pressure 3-10 bar. Drive Sytem Electropneumatic.
FR-L, V-FR-L, F-R-L, V-R-L, F-L are available.
|
|
C3
of plastic, modular design
5 and 20 µm, G1/4 - G1
outlet 0 - 8 bar, max. 8500 l/min
|
|
Assembled Combinations
Sizes Available: Miniature Series 1/8", 1/4" NPT and Compact Series 1/4", 3/8", 1/2" NPT
An assortment of filter, regulator, and lubricator combinations available.
|
|
|
A range extended for the air conditioning: AS2 - AS3 - AS5 complete Unit FRL, governor automatically-controlled, filters, membrane drier, pressurization progressive, gate valve. Flow from 150 to 10.500 possible Nl/min. Many accessories for all applications
|
|
|
|
|
|
Supply only "compressed air".
For compressed air, always use clean air chat does not contain corrosive gas.
Be sure to use non lubricated, filtrated dry air (équivalent to Class 1, 3, 2 - ISO 8571-3).
With a thorough understanding of compressed air characteristics, design a pneumatic circuit.
%u25A0 Where instantaneous stop holding at emergency stop is required, the same function as in the mechanical or hydraulic or electrical units cannot be expected.
%u25A0 There arise pop-up, jet-out and leaking phenomena caused by compressibility and expansibility, which are air characteristics.
Prior to use, always ensure that the product withstands the operating environ ment.
%u25A0 The product cannot be used in corrosive gas, chemical liquid solvent, water, water vapor (steam) and ozone atmosphère. When a product is exposed to water droplets, oil or metallic powder, such as spatters and chips, be sure to protect it.
%u25A0 No product can be used in the explosive gas atmosphère.
Always pay extra attention to the electric circuit during emergency stop, and cylinder opération, etc. during power failure.
Attach a "pressure switch" and "residual pressure discharge valve" to the compressed air inlet of the equi pment.
|
|
|
|
|
|
Filters, Regulators, and Lubricators (FRLs)
27 Modular Series Assemblies and Accessories
Filter, Regulator, Lubricator, trio (pictured)
- traditional trio design
- gauge packaged uninstalled for installation on either side
- bowl guard supplied standard
- filter, regulator, and lubricator options available
27 Series combo units offer pre-assembled units for fast installations. The integral filter/regulator offers space saving design. Duo and trio assemblies utilize the modular clamping system to ease installation.
Other Filters, Regulators, and Lubricator Products offered by Coilhose Pneumatics:
Economy Regulators
Pre-Set In-Line Pressure Regulators
Adjustable In-Line Pressure Regulators
In-Line Series F, R, Ls
Miniature Series F (also in Coalescing), R, Ls
Miniature Pro Line F, R, L, Assemblies and Accessories
25 Series F, R, L, A and A
26 Series F (also in C), R, L, A and A
27 Series Modular Series F(also in C), R, L, A and A
Heavy Duty Series F (also in C), R, L, A and Accessories
General Purpose Series F (also in C), R, L, A and A
Dessiccant Air Dryers
Mechanical Condensate Drains
Solid State Automatic Drain
Pressure Gauges
Vacuum and Hydraulic Gauges
|
|
Max. primary pressure: Metal bowl 18 Bar/255 PSI
Temperature: 0-60 oC
Water separation capacity: min 90 %
Effective bowl volume: Filter 45 cc
Lubricator 120 cc
Material: Housing: Zinc
Metal bowl: Zinc
Filterelement: Plastic
Top cover: Glassreinforced polyamid
Diaghragm: Chloroprenerubber with nylon reinforcement
Other parts: Brass, nitrile rubber
|
|
Max. primary pressure: Transparant bowl 12 Bar/170 PSI
Metal bowl 18 Bar/255 PSI
Temperature: 0-60° C
Water separation capacity: min 90 %
Effective bowl volume: Filter: 20 cc
Lubricator: 45 cc
Material: Housing: Zinc
Transparent bowl: Polycarbonate
Metal bowl: Zinc
Filterelement: Plastic
Top cover: Glassreinforced Polyamid
Diaghragm: Chloroprenerubber with nylon reinforcement
Other parts: Brass, nitrile rubbe
|
|
The enhanced ARO-Flo products come in four series, varying in port size and maximum standard cubic feet per minute (scfm) for optimal fit to the application and tools used:
-Miniature 1000 Series with 1/8” and 1/4” ports, and a maximum flow of 27 Liters/sec.
-All-new Compact 1500 Series with 1/4” and 3/8” ports, and a maximum flow of 109 scfm.
-Standard 2000 Series with 3/8”, 1/2”, and 3/4” ports, and a maximum flow of 104 Liters/sec.
-Heavy-Duty 3000 Series with 3/4” and 1” ports, and a maximum flow of 180 Liters/sec.
Key advantages of the upgraded ARO-Flo products are optimal performance and improved safety.
Safety
• Tested to ISO standards
• Locking Bowls
Performance
• Top tier flow performance
• Industry’s largest integral gauge
• 5 micron standard filter
Modularity
• Fully modular units and accessories
• Easy installation and maintenance
|
|
|
Norgren carries a complete range of air preparation products to fit any application. The most recent addition is the Excelon Pro, a no tools required, light weight FRL. Visit www.norgren.com/excelonpro for more information. All accessories are also available.
|
|
MD4
Modular Filters, Regulators, Lubricators with space saving design allowing for use in smaller spaces while providing high flow capacity.
MD4 series have modular clamps that can be disconnected from the front instead of the bottom, making filter element replacement and general maintenance much easier. There is also an option for an adsorber that is designed to remove vapors from the air line that cannot be removed by a coalescing filter. It allows for air to be free of oil and hydrocarbons.
|
|
A range extended for the air conditioning:
Complete unit FRL, governor automatically-controlled, filters, membrane drier, pressurization progressive, gate valve. Flow from 150 to 10.500 possible Nl/min.
Many accessories for all applications
|
|
Type FRCLM Series Combined Filter-Regulator-Lubricator Modular Unit (Assembled)
500 - 2800 l/min @ 7 bar
These fully assembled units comprise a conventional combined filter- regulator and lubricator (FRL) in modular configuration.
FEATURES
- Manual filter drain fitted as standard
- Auto drain option
- Push-to-lock non rising regulator control knob
- Constant lubricator oil flow & very low pick-up pressure
- Rugged metal bowl guards
TECHNICAL SPECIFICATIONS
- Medium: Compressed air
- Temperature Range: -10ºC to 60ºC
- Pressure range
- Standard: Input 0.5 to 10 bar
- Output 0.5 to 10 bar
- Options: 0.2 to 2 bar
0.2 to 4 bar
0.5 to 7 bar
- Filtration
- Standard: 40 µm
- Options: 5, 25, 50, 100 µm
- Max Input Pressure: 10 bar
- Gauge Ports: G1/8 (Two)
|
|
|
|
|
|
FRL's - 50 Series
High flow capacity FRL line - Filters, Regulators and Lubricators.
Features:
High Flow
High Pressure
T Handle Adjustment Regulator
Pilot Regulators to 2-1/2 NPT
Rugged Design
Metal Bowls with Sight Glass
1/4 to 1-1/2 NPT Size Range
Assemblies Available
FRL's - FlexiBlok FRL 14/22/32/42 Series
The Numatics 14, 22, 32, and 42 Series FlexiBlok¨ line is a series of high performance air preparation products. Introduced in 1997, the FlexiBlok¨ line is made from sturdy but light weight aluminum; perfect for applications such as robotic arms which cannot afford extra weight and less expensive to ship than zinc. The block head design with integrated mounting holes eliminates costly mounting plates and adapters, making the product easier to use and install. Private labeling is easy thanks to the special templates which snap securely in the front and back of the heads. These templates can be customized with names and/or logos; perfect for OEM applications.
The 14,22,32 series conforms to ISO 1179-1 and 228-1 requirements.
The 42 series will soon also conform to these requirements.
|
|
THREE-UNIT CLOSE NIPPLED COMBINATION
14A Miniature Series
FEATURES:
Unique Deflector Plate Ensuring Maximum Water & Dirt Separation
Solid Control Piston with Lip Seal for Extended Life
Non-Rising Adjusting Knob
Proportional Oil Delivery Over a Wide Range of Air Flows
Generates Oil Particles of 5 Micron or Smaller Downstream to Lubricate Systems Having Complex Piping Arrangements
|
|
|
The disposable Filtered Orifices are designed to remove most particulate contaminants in compressed air systems before reaching the orifice. They are available in ten color-coded orifice sizes .004” to .030” diameter. The filter media, a Dutch Weave 316 stainless steel screen, is available in 5, 25, 43, and 73 microns. Maximum supply pressure is 100 PSI.
|
|
Sample Gas Filters
The distance between the extraction point of sample gas and the analyser cabinet is normally bridged by tubes or hoses in continuous emission monitoring (CEM) systems. Depending on the method of analysis (FDIR, HFID, hot wet analysis, total hydrocarbons, etc.), these gas lines can be unheated or must be heated to prevent unwanted condensate formation.
Due to the nature of such installations, additional in-line filtration is required.
Bühler offers a wide selection of unheated and heated filters specifically designed for gas sampling applications.
|
|
|
|
Pneumatic filters, Compressed air treatment
