|
|
| Products 151 to 180 of 281 |
|
Filter for cleaning gases. The filter can be fitted with a filter insert of 2-150 µm. The body is fitted with a water and air bleeding screw.
|
|
WITT Gas Filters, some with condensation outlet, for pipelines and gas outlet points. For particles from 0.3 - 40 micron.
Advantages
- ultra fine filtering out of mechanical impurities through nickel chromium steel filter inserts
- broad range of uses - compatible with many technical gases (e.g. BAM approval for acetylene)
- change of filter possible while installed due to user-friendly design
- high flowrate thanks to flow maximising design
- condensate can be collected and removed using condensate drain (models 77 and 625)
- easy to install thanks to large choice of connections
- reliable filtering performance increases service life of downstream fittings and equipment
|
|
Next to a large variety of standard types, ROBU® produces many special designs also according to your specific requirements.
Round and rectangular discs of 450 x 450 mm and tubes up to 1.200 mm length are available.
|
|
FEATURES
- Cast Construction
- High Efficiency Over Wide Flow Range
- No Required Maintenance
- Economical Choice for Most Applications
- Removes 99% of Liquid and Solid Entrainment
Particles Larger Than 10 Micron
- Gas, Steam or Air Applications
OPTIONS
- Integral Trap
- Trap Heating Element
- ASME UM or U Code Stamp
- Water Gauge Tap
- Thermometer Tap
- Larger Drain Size
|
|
Large Flow Filtration for Air and Gas (1,600 scfm and larger)
Fabricated from high-quality carbon steel, PCC Series Filters are welded to ASME standards to provide large flow applications with exceptional air quality and low pressure drop. Designed specifically for use with our high performance air and gas filter cartridges, these filters can be used alone or as prefilters and afterfilters. D urable and dependable, PCC Series protects your compressed air and gas system and enhances dryer performance.
Flanged lid allows easy filter cartridge access. No need to disconnect drain valve or other tubing when changing cartridges
Sturdy vessel support legs simplify piping installations
Multi-element, carbon steel housing design 1,600 to 15,000 scfm
Easy to read differential pressure gauge standard on all models
Low housing pressure drop saves dollars (1 psi pressure drop costs, on average, $67 per year per 100 scfm at 6¢ per kWh).
|
|
Series 6610 line filters are designed for line mounting in tubing with compression-type fittings. They are ideal for filtering liquids and gases to protect sensitive instruments.
Mott Series 6610 line filters are offered for three tube sizes, in a variety of media grades.
|
|
Description:
The Model FD-1500 Filter Dryer filters and de-hydrates supply gas for Flexflo™ Pilots. The FD-1500 Filter-Dryer provides superior filtration and dehydration with 110 square inches of 10 micron filtering media and 2.0 pounds of silica gel. The FD-1500 incorporates an easy-to-replace "spin on" cartridge made up of a high quality, high capacity nylon and fiberglass filter element reinforced with stainless steel mesh. All FD-1500's are fully Hydrotest to 2.5 times the working pressure to ensure the integrity of the pressure vessel. Final Filter Element.
|
|
Headline produces an extensive range of filters for instrumentation and analysis applications. We have solutions for in-line, particulate and coalescing, and bypass or fast loop. All housings offer high flow rates and fast response times.
Housings are available in a variety of materials, 316L Stainless Steel, Aluminium, PFTE, PVDF, Nylon, and Polypropylene, as well a range of exotic materials such as Hasteloy, Monel, and Titanium. Sizes range from 1/2" to 2", with pressures to 700 Bar.
|
|
|
Magnetic Filter for liquids. These are purifiers suitable for elimination of magnetic particles contained in any type of more or less fluid liquid. They allow removing obstructions in burners, gums, valves and further parts of the installation.
|
|
- Magnetic filter
- Easy maintenace an cleaning
- Housing in brass or bronze material
- Connection from 1/2" to 3" Gas-F
- Magnetic separator in Barium-Ferrite
- Basket filter AISI-304
|
|
TYPICAL APPLICATIONS
EFS
Standard size housings available with 30 (590), 60 (250), 100 (149), and 150 (99) mesh (micron) reusable, stainless steel filter cartridges. Units measure 11.25" long and feature a 1" NPT intake and dual 1" NPT discharge ports (3/4" reducers provided).
FEATURES
Graymills Superflo filters are designed to overcome the typical pressure drop and reduced flow due to clogging that occurs with ordinary filters. A permanent magnet suspended over the intake port traps ferrous particles which find their way into the fluid, and diffuses the flow outward into the filter screen flutes. Filtered material is trapped on the inside of the removable/reusable stainless steel filter cartridge. To clean, just remove the cartridge. All the contaminants come out with it. Self draining. No wasted fluid or messy leftovers to deal with. Stainless steel filter cartridges are available in four different mesh screens.
|
|
|
Drop-in magnetic separator filters, designed for fluid tanks and reservoirs, pull fine particles out of fluids and hold them until the unit can be cleaned and dropped back in. Used in tanks or other containers having low to moderate flows. Direct blast of fluids over unit is not recommended.
|
|
|
|
|
|
These magnet filters are used to filter ferrous particles from liquids and they are frequently used in hydraulic circuits and cooling systems. The magnet system is constructed from ceramic magnets and the unit is built into a stainless steel (AISI 304) casing. For cleaning, the magnet system is simple to remove by undoing several quick-release fasteners. A special double-walled version is available for use in heated pipeline systems (for example, separating ferrous particles from molten chocolate and cheese). Bakker Magnetics magnet filters are available in a number of versions for special applications. For situations where extremely stringent requirements for ferrous separation have to be met and/or tiny ferrous particles (m region) have to be extracted, a system can
be fitted with Neodymium magnets (add "/01" to the article number). A special version is available for use in systems with high pressures. Sanitary models are also available for applications in, for example, the food industry. For processing large quantities of raw materials, heavy-duty versions can be supplied. These versions have a processing capacity from 1000 to 8500 l/min.
|
|
Bunting General-Purpose Grate Magnets provide a properly configured, high-density magnetic field to trap and hold ferrous fines, fragments, and small metal objects. Stainless steel tubing and frames are welded into strong, integral units. They can be installed - or simply laid - inside hoppers, housings, and bins - and easily removed for cleaning. Grates are built for low-abrasion applications and should measure at least twice the size of your outlet opening, so as not to restrict product flow.
General-Purpose Grate Magnets consist of multi-polarity 1-inch diameter cartridges arranged on 2-inch centers. They're available in round, square, and rectangular configurations from 4" through 36" in size. They can be ordered without baffles for freer flowing materials, and with angular baffles for maximum magnetic protection.
|
|
As pre-cleaners or main cleaners for subordinate applications and magnetisable chips, magnetic filters offer a good and reasonably priced filtration method.
Turbo Separator AG produces magnetic filters with flow rates of 100 - 400l/min.
Depending on the application area, these magnetic filters can also be built up in cascades.
Magnetic filters from Turbo-Separator can be installed as integrated components of a system or built on as accessory products.
Special requirements call for special solutions - we shall implement your wishes, with unconventional solutions if need be! (SE magnets)
|
|
Benefits:
- extremely small total height
- easily compatible with CLEARPOINT® filters
- top-grade design
- all functional components are built-in and well protected inside the housing
- guaranteed drying, as humidity is removed in any case
- no alteration of the usual compressed air composition
- low purge air demand
- service-free, as there are no wearing parts in the dryer (merely the regular change of the filter elements is required)
- no ecologically undesirable drying agents
|
|
S u n s e p use diffusion prinziple for drying air, by a polymere microfibre hollow membrane. The sunsep-w can ensure a dewpoint up to -40°C. Outlet dewpoint depends on the inlet dewpoint temperature.
Type max. capacity Weight Microfilter (Prefilter)
Sunsep at 8 bar a without prefilter
(l/min) (kg) SWC M04-70 030 0,05 G 2 XP
SWC M08-100 70 0,26 G 2 XP
SWC M15-100 120 0,27 G 2 XP
SWC 01-150 200 0,39 G 2 XP
SWC 02-250 300 0,69 G 2 XP
SWC 02-200 400 0,45 G 2 XP
SWC 03-250 450 0,71 G 2 XP
SWB 01-100 200 0,22 G 2 XP
SWB 01-200 200 0,26 G 2 Xp
SWB 05-100 800 0,66 G 3 XP
SWF M06-400 025 0,12 G 2 XP
The regeneration air requirement quantity is 15-18%. Flow rate as well as the regeneration air requirement are dependent on the operating pressure, inlet temperature and the dew-point of the compressed air. The maximum permissible operating pressure is 8.5 bar min/max compressed air and ambient temperature: -20°C/55°C. Higher operating pressures available on request.
|
|
Air Line Lubricator
Sizes Available: Miniature Series 1/8", 1/4" NPT, Compact Series 1/4", 3/8", 1/2" NPT, Large Series 1", 1-1/2" NPT
Air line mist lubricator distributes oil into the compressed air line, significantly increasing the life of downstream equipment such as valves and actuators.
Bowl available in transparent polycarbonate or metal zinc die cast.
Bowl capacity: Miniature: 17cc, Compact: 160 cc, Large: 1 litre
|
|
The 09L Hi-Flow Mist Air Lubricator is designed to provide lubrication for most general applications in a pneumatic system. Units should be installed close to the application ensuring effective distribution of oil to pneumatic components.
FEATURES:
Metal Bowl With Sight Gauge & Manual Drain - Standard
Proportional Oil Delivery Over a Wide Range of Air Flows
Bowl Can Be Filled While Air Line is Under Pressure
Transparent Sight Dome for 360° Visibility
|
|
|
|
|
|
|
Especially suited for use with Airpot actuators and Airpel cylinders where low friction/low hysteresis, sensitive response, long life, clean operation, and extreme temperature are critical requirements. Offered in both compact and standard configurations for moderate and high flow, Airpot FFR systems are available with standard or precision regulators for precise control and sensitivity. Airpot FFR systems are composed of lightweight aluminum/resin hybrid material built into a compact and modular 40mm x 40mm envelope per component (compact series). Standard and Precision series (with increased low pressure sensitivity) regulators are available; all with hand adjustability and single push lock operation. The precision series offers a pressure range of 0.005 to 0.4 MPa and sensitivity within 0.1% of the full scale. Port connections are available with NPT or G metric threads. Each system is equipped with dual filtration modules that remove particles, dust, oil, moisture and mist down to 0.01 micron. This two stage filtration system is comprised of a 5 micron dust and moisture filter augmented by a 0.01 micron coalescing filter. The long life media transitions from a coarse outer surface to a fine interior structure to reduce clogging prolong life and prevent rust formation. All filters boast a standard corrosion resistant filter bowl guard, one quarter turn filter element removal and a unique O ring slip prevention design. FFR gauges offer highly visible color zone indicators, field adjustable limit marks, flat face design with a non- protruding (standard series, compact and high flow types) gauge embedded in the module made to JIS3 grade with either MPa or PSI readings.
|
|
Features
* High Control Sensitivity of 1/8" water column
* Pressure balanced supply valve
* Separate control chamber
* Aspirator tube design
* Nine pressure ranges available
* Check valve option
* "No yellow Metals" option
|
|
|
The Type-100 is a high precision, multi-stage pressure regulator. This pressure controller provides the highest level of regulation accuracy and repeatability available. The Type-100 is ideal for applications that call for the utmost of control and maximum stability under variable operating conditions. A stainless steel measuring capsule is used as a sensing element to activate the high gain servo balanced control mechanism in which the main valve is controlled by a pilot valve.This allows for greater accuracy and eliminates many of the problems associated with conventional regulators using range springs and diaphragms.
|
|
Features
- Control sensitivity of 1/4" water column variation allows use in precision applications.
- A compensating diaphragm lets the regulator remain unaffected by supply
pressure changes.
- Flow of up to 40 SCFM with 100 psig supply allows use in applications with high
flow requirements.
- An aspirator tube compensates downstream pressure droop under flow conditions.
- A separate Control Chamber isolates the diaphragm from the main flow to eliminate hunting and buzzing.
- Unit construction lets you service the Model 30 without removing it from the line.
- Canadian Registration Number (CRN) Certification for all territories and provinces
|
|
General Description
316 stainless steel for the offshore, food, pharmaceutical and allied industries. Provides pressure regulation of compressed air for use in these industries.
- 316 Stainless steel throughout. Large flow. High relief flow. Integral mounting holes. Secure labelling. Tagging facility built in.
- Full range of accessories.
Filter Unit:
- Large 25 micron standard element with manual or automatic drain for the removal of liquids and solids. 5 micron element option available.
Operating Fluids:
- Gases
Filtered lubricated or non-lubricated air, inert gas, sweet (natural) gases. Sour gas option available
- Liquids
Low pressure hydraulic, mineral oil or water
|
|
ROSS regulators are made in a wide range of sizes to suit nearly all industrial requirements for pneumatic pressure regulation. Good pressure regulation is essential to the efficient use of pneumatic equipment. A compressor may supply
air at 150 psig, but most of the equipment will operate best at lower pressures. A cylinder, for example, may develop sufficient force for its purpose with 50-psig air. Remember that compressed air is costly, so using higher air pressure than necessary is wasteful, and may also shorten the life of the cylinder. A general purpose pressure regulator is the answer for greater economy and efficiency.
|
|
B3000
filter regulator, stainless steel throughout
5 and 50 µm, G1/8 - G1
outlet 0 - 3 / 50 bar, max. 6000 l/min
|
|
Features
* High Flow Capacity
* Standard 5-micron filter
* No "yellow Metals" internal construction
* Epoxy coated finish
* Non-bleed design
* Integral Relief Valve
* Standard Gauge Port
* Filter Dripwell Drain Plug
* Standard Tapped Exhaust
* Soft Relief Seat
|
|
|
The ControlAir Type-850 and Type-860 are compacts unit that provide low-cost, high performance pressure regulation of compressed air (Type 850 and Type 860) or water (Type 860). Designed specifically for the OEM market, these units are ideal for compressed air or water pressure control applications. The highly sensitive diaphragm-operated design delivers accurate downstream pressure by eliminating the problems caused by sticking in piston designs utilized by competitors. A molded rubber supply valve provides accurate regulation and prevents leakage.
|
|
|
Designed for use as full-flow or partial flow filters and for the low pressure range up to 25/60 bar, medium pressure up to 210 bar and high pressure up to 450 bar, MAHLE pressure filters are ideal for application as main-line filters, flangemounted filters and filters in intermediate plate design. Rugged casings, streamlined design and an extensive range of accessories provide the optimal solution capable of meeting every market requirement.
|
|
Graver Pressure Filters have proven their ability to meet any water filtration problem efficiently and economically in hundreds of installations worldwide, and in a wide range of industrial plants, municipalities and utilities.
Graver Pressure Filters are available in vertical and horizontal designs, in any convenient size, and with valve arrangements to meet any custom or special requirements.
For individual bed areas of 100 square feet or less, the vertical pressure filters are usually furnished. For greater areas, a horizontal pressure filter is more practical. In applications where a large quantity of water is to be filtered, a battery of filters is installed in parallel to provide the necessary throughput.
|
|
|
|
Pneumatic filters, Compressed air treatment
