|
|
|
|
|
|
|
MTM Power GmbH, the specialist for high quality power supplies, offers in its program DC/DC converters for automotive applications. The series WRC is available with 30, 60, 100 and 150 W. The converters are designed for mobile use acc. to EN 50 155, LES-DB-BN 411 002 and IEC 571-1 (railway, automotive). The battery voltages 24, 36, 72, 90 and 110 V +40/-45 % are covered with three input voltage ranges. All four power ranges have a high efficiency and are available with single or dual output voltages. The converters have an extreme high reliability (MTBF >1.000.000 h, TA = +40 °C) and an isolation of at least 2,1 kVDC (prim.-sec.). The temperature range is -40...+85 °C acc. to EN 50 155. Other important features are resistance against vibrations and reverse polarity protection at the input. The power supplies can be used in 19" racks or for wall mounting with H15 connector. The series WRC needs no ground load, is short circuit protected and has extensive monitoring and protection systems.
|
|
|
|
|
|
|
The DC/DC power supply systems of the series MPG from MTM Power, the specialist for high-quality unparallely power supplies, are designed among others for different applications in transportation, telecommunications and the charging of lead batteries during stand-by parallel operation. The universally useable, modular and easy-to-scale system is based on the DC/DC converters of the series PCMD200W and PCMD400W which are proved in transportation applications. The series MPG2 is available with 2 plug-in positions and a total output power of 500-800 W and the series MPG3 with 3 plug-in positions and a total output power of 750-1.200 W. With different wide input voltage ranges between 14,4 VDC and 154 VDC, the devices supply an output voltage of 12, 24, 48, 72 and 110 VDC. The output voltage operates with UI characteristic curve. The system can be switched into an energy-saving stand-by operation via a remote control input. Further features are signalling of input and output voltage by an LED as well as a potential-free power good signal. The whole system is passively cooled by convection and is designed for an ambient temperature range of -40...+70 °C.
|
|
|
|
|
|
MTM Power GmbH, the specialist for high quality power supplies, has designed the DC/DC converter series SMM50 for the use in vehicles, particularly for railway applications. These converters have an output power of 50 watts and are suitable for the stationary use as well as for the mobile use acc. to EN 50 155. The nominal input voltages are 24 VDC ((14,4…50,4 VDC), 48 VDC (28,8…100,8 VDC) and 110 VDC (43,2…154 VDC) and 230 VAC (85…264 VAC). Due to these input voltage ranges, the converters can be used in all on-board power systems. The output voltages are galvanically separated and are available as single, dual and triple versions. Further features are vibration and shock resistance acc. to IEC 68 T.2-27, high efficiency of 79...89 % and reverse polarity protection at the input. The devices are prepared for the use in 19" racks and have a H11 connector acc. to DIN 41 612. The dimensions are 173,0 x 38,7 x 111,2 mm or 177,0 x 40,2 x 128,4 mm (length x width x height). The series SMM50 needs no ground load, is short circuit protected and has various monitoring and protection systems.
|
|
|
“Ideal miniaturization should be enhanced with increased of efficiency”. The SV-series has been developed based on this fundamental design idea. This series has been developed in a super-small size, with high efficiency, high performance and high reliability. For example, the introduction of a “double side printed PCB with through” plus the latest design of eliminating capacitors from the input circuit have enabled improved reliability and longevity of the converter.
|
|
|
Sens-Tech offers a remotely controlled, multi-channel, photomultiplier power supply system. HVSys provides individual channel control and monitoring of the high voltage power supply of each channel, using only 3 wires. A unique feature is that HV is generated on the base of the photomultiplier, avoiding the inconvenience and problems associated with high voltage distribution. All that is required is a +12V supply with sufficient current capability for the number of channels chosen; the supply current required is less than 25 mA per channel.
|
|
|
Static Clean International offers power supplies for both static control and charging applications. Our power supplies are provided as low power, high impedance, step-up transformers potted with internal current limits.
|
|
Model ORION-D3002DDP
300W -48V & 24V DC input DC/DC PS/2 ATX power supply
Mini-redundant DC to DC power supply suitable for 2U and larger chassis
Active PFC, full-range input
-38 V DC to 72V DC output for telecommunication applications
Test equipment for telecommunication applications
Model ORION-B3502
350W 2U ATX redundant power supply with active PFC
Low profile power supply, suitable for 2U and node chassis
Dual ATX 12V power connector for dual Intel® Xeon processor based server board, ROBO-8820VG2
Active PFC, full range input
Total output power of +5V, +3.3V and +12V is 328W
Model ORION-3002
300W PS/2 hot-swap redundant power supply
Mini-redundant power supply suitable for 2U and up chassis
Max. +5V standby output is 2A
|
|
| ... products without technical information |
| |
|
|
