AC/DC power supplies

Power: 480 W
Input voltage: 400 V - 500 V
Output voltage: 24 V

... and 3-phase stabilized SITOP PSU2600 power supplies are specially designed for use in medical engineering. Overview Three-phase power supply for medical engineering The ...

Power: 120 W
Input voltage: 120 V - 230 V
Output voltage: 3 V - 52 V

... output voltages What to do if, for example, you need a power supply unit for 5 V, one for 15 V—and then one for 38.5 V as well? Install a special power supply every ...

Power: 240 W
Input voltage: 120, 230 V
Output voltage: 48 V

Overview This power supply is optimized for 48 V industrial applications with a focus on single-series and special-purpose machines in the manufacturing industry with power demands up ...

Power: 2,000 W - 3,000 W
Input voltage: 190 V - 250 V
Output voltage: 300 V

... Benefits -AC, DC and AC+DC power source -Low total harmonic distortion meets the IEC 61000-3-2 standard -Comprehensive measurement capabilities Vrms, ...

Power: 5,000 W
Input voltage: 170 V - 265 V
Output voltage: 0 V - 1,000 V

... PVS60085, and PVS60085MR programmable DC power supplies offer clean output power up to 5.1 kW, excellent regulation, and fast transient response time characteristics in an industry-leading ...

Power: 3,000 W
Input voltage: 170 V - 265 V
Output voltage: 0 V - 600 V

... PVS60085, and PVS60085MR programmable DC power supplies offer clean output power up to 5.1 kW, excellent regulation, and fast transient response time characteristics in an industry-leading ...

Power: 20, 25, 50 W
Output voltage: -50 V - 50 V
Current: 1, 1.5, 3 A

The R&S TS-PSU module uses two completely separate floating source and sink channels that work for various ground reference levels. These can work at up to 50 V and 50 W at a time. This can manage sink, souce and bipolar modes for four-quadrant ...

Power: 244, 85, 122 W
Input voltage: 24 V - 480 V
Output voltage: 29.5 V - 31.6 V

Particularly space-saving design Low heating of the control cabinet High power reserves Low inrush current Safe switch-off by circuit breakers in case of short circuit

Power: 240 W
Input voltage: 100 V - 240 V
Output voltage: 24 V - 28 V

For the regulated power supply for controllers, sensors, actuators, and industrial electronics Low power loss thanks to high efficiency High mains buffering time Particularly ...

Power: 80 W
Input voltage: 110 V - 300 V
Output voltage: 24 V - 28 V

For the regulated power supply for controllers, sensors, actuators, and industrial electronics Low power loss thanks to high efficiency High mains buffering time Particularly ...

Power: 30 W
Output voltage: 24 V
Current: 1.25 A

... Compact Power Supply (787-2850) in a DIN-rail-mount enclosure offers a lot of power in a scant 35.5 mm (1.398"). Thanks to the slim design, it saves around 33% more space in the control ...

Output voltage: 12 V
Current: 2.5, 5, 8 A

... 43880. Developed for distribution cabinets, these highly reliable power supplies also meet the electrical safety requirements of EN 60335-1. In addition to high performance, WAGO’s ...

Power: 2.5 W - 1,920 W
Input voltage: 12 V - 500 V
Output voltage: 5 V - 48 V

EPSITRON® PRO Power – Power Supplies Applications with high output requirements call for professional power supplies capable of reliably handling power ...

Input voltage: 90 V - 264 V
Output voltage: 24 V

Miyachi Unitek's range of Advanced Dual Pulse CD welders has a trademarked charging unit for better repetition times and pulse rate times (Four pulse widths). It provides high weld and process performance because of its easy to use weld ...

Pulse Heated Reflow Soldering Power Supply offers closed-loop temperature and time control. It stores 15 heating profiles which can be programmed remotely using RS-232/485. This equipment also boasts ...

Power: 148 W - 150 W
Input voltage: 85 V - 264 V
Output voltage: 24, 12, 48 V

With the PCMAT150 S24, MTM Power® introduces a new generation of AC/DC modules which can be installed as a decentralised power supply for industrial ...

Power: 51 W - 60 W
Input voltage: 90 V - 264 V
Output voltage: 5.1, 12, 15, 24, 48 V

With the series PMAT/PCMAT60, MTM Power® expands its program with the third generation of AC/DC modules for reliable supply of electrical and electronic systems. The ...

Power: 100 W
Input voltage: 90 V - 264 V
Output voltage: 24 V

Operating Temperature Range -40...70 °C OV3 Overvoltage Category Completely Vacuum Encapsulated Baseplate Cooling Rugged Design Industrial Connectors

Power: 450 W
Input voltage: 85 V - 370 V
Output voltage: 12 V - 53 V

The TPP 450A Series of 450 Watt AC/DC power supplies feature a reinforced double I/O isolation system according to latest medical safety standards (60601-1 3rd edition, ...

Power: 10, 8.6 W
Input voltage: 85 V - 370 V
Output voltage: 3.3 V - 48 V

The TMPS 10 series comprises ultra compact AC/DC power supply modules in a lightweight fully encapsulated plastic casing for PCB mount. Beside the latest safety approvals ...

Power: 15, 13.2 W
Output voltage: 3.3 V - 48 V
Current: 313 mA - 4,000 mA

The TPP 15 AC/DC power supplies feature a reinforced double I/O isolation system according to medical safety standards IEC/EN/ES 60601-1 3rd edition for 2 x MOPP approved ...

Input voltage: 230, 115 V
Output voltage: 0 V - 72 V

LSP Konstanter series 32K laboratory power supplies are high precision DC power supplies for use in R&D, production, service and training. Three variants ...

Power: 1,500, 800, 4,500, 3,000, 500 W
Input voltage: 115, 230 V
Output voltage: 0 V - 60 V

... series of KONSTANTER power supplies provides you with top quality manual and remote controllable DC power supplies for laboratory and system use. Equipped ...

Power: 120, 240, 320 W
Input voltage: 230 V
Output voltage: 0 V - 80 V

Series SLP 120, 240 and 320 KONSTANTERs (Single-Output Laboratory Power Supplies) are single output, primary switched-mode laboratory power supplies for universal use ...

Salicru’s DC power-S energy systems feature the following components: DC-S rectifier modules, subracks, a control and monitoring system, a communications module and a DC ...

Power: 3 W
Input voltage: 100 V - 240 V
Output voltage: 5, 12, 24 V

The SP Series from Autonics is a DIN rail mounting type switching power supply model that is specially designed as a power source for universal input. It is capable of driving a variety ...

Power: 15 W - 240 W
Input voltage: 100 V - 240 V
Output voltage: 5, 12, 24, 48 V

... Rail Switching Mode Power Supplies The SPB series switching mode power supplies offer high power conversion efficiency and stable power ...

The SPS-24/1,5, manufactured by SIMEX®, is a 30-W single output industrial DIN-rail power supply which features a fan-less design for compatible installations involving TS35/7,5 or TS35/15 industrial ...

... utilized in general industrial applications such as factory automation, electromechanical industry, data communication, IT, power-distribution boxes, control panels, building automation and household appliance control.

... /3,2 model engineered by Simex, is a DIN rail power supply that features a fan less design for set up on TS35/7,5 or TS35/15 industrial rails. This device operates on a 3.2 A rated current and on a 24 ...

... controlling piezo actuators between -20 and 150V the powered benchtop case RK42F3U-LC75B solution includes a RK42F3U case and an AC-DC converter LC75B. Available options Status Standard

... controlling piezo actuators between -20 and 150V the powered benchtop case RK42F4U-LC75C solution includes a RK42F4U case and an AC-DC converter board LC75C. Available options Status Standard

Output voltage: -20 V - 150 V
Current: 0.75 A

... controlling piezo actuators between -20 and 150V the powered subrack RK84F4U-1LC75B solution includes a 19'' RK84F4U subrack and an AC-DC converter board LC75B. The solution offered is ready for cabinet ...

Input voltage: 230 V
Current: 20, 4 mA

... galvanic-insulated power supply for transmitters.For the 2-wire transmitter (connection between H+ and J- terminals) the device powers the 4/20 mA sensor (16.5 V at 20 mA). If the BXNT6 ...

Input voltage: 230 V

... is an intrinsically safe power supply.The BXNE**1 version is equipped with a 24 V DC remote control (E+F-). A 24 V input voltage (E+F-) therefore actuates the relay, which actuates the ...

Input voltage: 24 V

... designed to supply instruments in hazardous area. Control by 24V remote control or by switch in safe area. Input:without (direct supply), 24VDC remote control or switch Output: different intrinsically ...

Input voltage: 16.5 V
Output voltage: 10 V

Repeater power supply in a 6 mm housing with calibrated switching of output signals, HART transmission and protective separation. Repeater power supply for 2-wire transmitters ...

Input voltage: 18 V
Output voltage: 13 V

The WG 21 repeater power supply is used to supply intrinsically safe 2-wire transmitters. It supplies the transmitter with power and transmits the measurement ...

Input voltage: 17 V
Output voltage: 30 V

... repeater power supply is loop-powered. It is used for galvanic hazardous-area separation of a 2-wire supply line and transmits both 4 ... 20 mA and HART® signals in both directions. With ...

Power: 250 W - 1,000 W
Input voltage: 110 V - 230 V
Output voltage: 0 V - 40,000 V

... measure your high voltage power supplies and HV system performance. HV Rack configurable power systems enable you to select, control, and monitor your high voltage power ...

Power: 1,000 W
Input voltage: 85 V - 264 V
Output voltage: 1 V - 348 V

Fanless 1000 W, Intelligent, Modular Power Supply Platform Advanced Energy's CoolX1000 is a highly flexible and compact, fanless power supply ideal for vibration and ...

Power: 0 W - 1,800 W
Input voltage: 85 V - 264 V
Output voltage: 1 V - 348 V

... multiple-output modular power supplies is ideal for medical, life science, industrial, and harsh-environmental applications. The power supplies support series and parallel ...

Power: 0 W - 130 W
Input voltage: 100 V - 240 V
Output voltage: 12 V

Universal power input support 100 to 240VAC High power conversion efficiency Supports over voltage protection Continuous short circuit protection Supports over temperature protection Active PFC ...

Power: 0 W - 30 W
Input voltage: 100 V - 240 V
Output voltage: 52 V

... single port, PoE PSE solution for remote PoE PD devices. Generating up to 30W, POA-1000A supplies remote power for new applications such as wireless Access Points, pan-tilt-zoom ...

Input voltage: 0 V - 240 V
Output voltage: 52 V
Current: 0.8 A

... single port PoE solution for remote PoE PD devices. The low power PoE power source (PSE) injector delivers 48VDC power to PoE-devices ...

Power: 480 W
Input voltage: 90 V - 370 V
Output voltage: 24, 48 V

Universal AC input / Full range Protections: Short circuit / Overload / Over voltage Cooling by free air convection Can be installed on DIN rail TS-35/7.5 or 15 Built in DC OK active signal LED indicator ...

Power: 250, 500 W
Input voltage: 85 V - 110 V
Output voltage: 3.3 V - 100 V

... specific 365 Volt regulated output. It is also suitable for different universal AC inputs in DC application. In addition, its power factor is 0.99, efficiency is 90% or better and its ...

Power: 1,000 W
Input voltage: 85 V - 250 V

... different series of this device include - FD/MD/LFD/LMD/LPD/PD and HPD of DC-DC converters that are capable of providing output voltage from 3.3V to 300V DC. HPHA1's 365V DC ...

Power: 3 W - 15 W
Input voltage: 90 V - 130 V
Output voltage: 3.3 V - 48 V

The AC-DC Switching Power Supplies gives an Excellent line regulation ± 1% (90-130 VAC), Excellent load regulation 25% to 100%, ± 2% , Continuous short circuit protection ...

Input voltage: 24 V - 30 V
Output voltage: 24 V - 30 V
Current: 4, 2, 0.4 A

Closed loop controlled current Power Supply included in a very compact enclosure with integrated DIN rail fixing system. Current regulation based on microcontroller technology, offering accurate current ...

Input voltage: 85 V - 375 V
Output voltage: 22.5 V - 28.5 V

... voltage 22,5..28,5 V DC ●Current up to 0,6 A ●Stabilized, short circuit proof ●Power limiting with positive characteristics Technical Data Input Supply voltage:85..264 V AC, ...

Input voltage: 85 V - 265 V
Output voltage: 5 V - 24 V

Full 2-port isolation ●Adjustable output voltage ●Current up to 2 A ●Stabilized, short circuit proof ●Power limiting with positive characteristics Technical data Input:see ordering code Frequency:47..63 Hz Operating temperature NG1000-1/2-X:-10..+50 ...

Input voltage: 85 V - 380 V
Output voltage: 5 V - 30 V

... Adjustable output voltage 5..30 V DC ●Current up to 1.2 A ●Stabilized, short circuit proof ●Power limiting with positive characteristics Technical data Input - NG500-1-0:85..265 V AC, ...

Power: 24 W
Input voltage: 85 V - 264 V
Output voltage: 24 V

This rail power supply has a slim structure. It features a universal AC input and extended working temperature. This item is protected from short circuit, overload, and over voltage. ...

Power: 40.8 W
Input voltage: 85 V - 264 V
Output voltage: 24 V

The DIN Rail Power Supply 32103-3 engineered by Comtrol Corporation, features a universal AC input along with an air convection cooling. This power supply ...

Power: 60 W
Input voltage: 85 V - 264 V
Output voltage: 24 V

... maximum efficiency rate of 88%, this power supply offers zero load power consumption. Additional features include short circuit, overload and over voltage protection. The status of the ...

Power: 75 W
Input voltage: 85 V - 264 V
Output voltage: 24 V

The PSU24-075 model engineered by JVL, is an AC or DC switch-mode power supply intended for DIN rail applications. This device runs on a 24 V DC voltage ...

Power: 200 W - 1,200 W
Input voltage: 150, 80, 40 V
Output voltage: 24 V

The JVL PSU40, PSU80 and PSU150 are power supplies. This devices are designed with a compact size and a robust style. The PSU40, PSU80 and PSU150 are created with a built-in overload protection. These ...

Power: 100 W - 1,000 W
Input voltage: 115 V - 230 V
Output voltage: 40 V - 150 V

... great replacement for conventional power supplies such as PSUxx from JVL. They feature outputs of 40, 80 and 150 V DC, and power up to 1,000 W (4kW peak). They are commonly ...

... a microammeter (500 µafs).a 3-way galvanic seclusion among Power supply/ info/ yield circuits guarantees the respectability of your figures. It could be asked for with low or high power ...

Power: 0 W - 36 W
Input voltage: 110 V - 315 V
Output voltage: 24 V - 24 V

Z-SUPPLY is single-phase switching power supply with AC input rated voltage from 110 Vac to 230 Vac @ 47 Hz-63 Hz, 0.7 A and DC input rated voltage from ...

Power: 150 W
Input voltage: 90 V - 264 V

... convection-cooled, power supply for ATX-compatible Single Board Computers (SBCs). It is a universal design that accepts 90 to 264VAC input and generates five different output voltages as well as supporting ...

Power: 35 W
Input voltage: 88 V - 264 V
Current: 1.5 A

The PS-RS35-24 is a small, convection cooled 35W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 1.5A of current at 24 volts. The 24 voltage ...

Power: 50 W
Input voltage: 88 V - 264 V
Current: 10 A

WinSystems’ PS-RS50-5 is a small, convection cooled 50W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 10A of current at +5 volts. The ...