|
|
The Viscotek membrane Degasser works in-line, degassing eluent for optimal pump performance and improved detector baselines. The multi-channel membrane degasser is chemically resistant to a wide range of GPC eluents and has 2, 3 or 4 channels, each of which can be used for a different eluent.
Key Features include:
Efficient in-line degassing improves pump performance
Reduced baseline noise, especially for Light Scattering and Viscometer detectors
Chemically resistant to a wide range of GPC eluents
Recommended for use with triple detection
|
|
|
|
|
|
Smartline Manager 5000 (LPG, Degasser, Interface)
Fully equipped analytical version of the Smartline Manager 5000, which includes a low pressure gradient (LPG) module, a 4-channel degasser module, and an interface module for 3rd party instruments.
The combination of the Smartline Manager 5000 with the Smartline Pump 1000 provides for a quaternary LPG system. The valve block built of PEEK is controlled by the Smartline Pump 1000 and delivers gradient mixtures of the highest precision over the entire flow range up to 50 ml/min.
An optional integrated 4-channel degasser module provides outstanding performance through its use of a newly developed micro vacuum pump while taking up only a minimum of space. The gas diffusion rate has been improved by a factor of 200 - 300 times, thanks to a new amorphous fluoropolymer rather than a regular Teflon membrane. Excellent chemical and physical stability parameters, as well as the reduction of the internal chamber volume to less than 0.5 ml are convincing features. The analytical Smartline degasser module can be used for flow rates of up to 10 ml/min
The Smartline Manager 5000 can optionally be equipped with an interface module. This interface module enables highly precise data acquisition and provides for the control of non-Knauer devices over analog and relay outputs. Supports 4 channels at sample rates of up to 10 Hz or one channel at up to 50 Hz.
|
|
Feed Water Deaeratores
Packaged Deaerator systems, 5,000 to 200,000 PPH. Conditions feedwater to 0% CO2 and .005cc/liter of oxygen.
imageThe HURST "OXY-MISER" deaerating boiler feedwater system eliminates the need of expensive oxygen scavenger chemicals and also offers the following advantages:
* Removes carbon dioxide as well as oxygen.
* Raises the boiler feedwater temperature, eliminating thermal shock in boilers.
* Improves overall boiler room efficiency.
* Feedwater pumps are sized for each individual application - assuring total compatibility and optimum operation.
* Vessels are ASME Code constructed for 50 psig.
* Compact design means smaller boiler room requirements.
|
|
|
|
|
|
Dissolved gases such as oxygen and carbon dioxide must be reduced in Boiler Feed Water in order to prevent boilers and steam circuits from corrosion. The thermo-physical deaeration process is by far the most applied technology when a reduction of oxygen to only a few parts per billion is required. While part of the BONO Group, ARTES Ingegneria is in the business of Deaerators since 1958.
The degassing process is achieved in the deaerating tower where make-up water is atomised on a set of special packing that increases the contact surface between water and steam. Oxygen and carbon dioxide are stripped by the steam flow and vented through a calibrated orifice. Deaerated water is collected in the storage tank so as to assure an adequate “Hold-up” time for the boiler downstream.
According to the design capacity and steam flow, the deaerating tower may be arranged on a vertical or horizontal geometry so that, in the latter case, a larger surface of mass and heat transfer is implemented.
Deaerators are manufactured and marketed on BONO Artes’ own proprietary design in order to assure the complete responsibility of the concerned unit.
|
|
Feed Water Deaeratores
Packaged Deaerator systems, 5,000 to 200,000 PPH. Conditions feedwater to 0% CO2 and .005cc/liter of oxygen.
imageThe HURST "OXY-MISER" deaerating boiler feedwater system eliminates the need of expensive oxygen scavenger chemicals and also offers the following advantages:
* Removes carbon dioxide as well as oxygen.
* Raises the boiler feedwater temperature, eliminating thermal shock in boilers.
* Improves overall boiler room efficiency.
* Feedwater pumps are sized for each individual application - assuring total compatibility and optimum operation.
* Vessels are ASME Code constructed for 50 psig.
* Compact design means smaller boiler room requirements.
|
|
|
|
|
|
Dissolved gases such as oxygen and carbon dioxide must be reduced in Boiler Feed Water in order to prevent boilers and steam circuits from corrosion. The thermo-physical deaeration process is by far the most applied technology when a reduction of oxygen to only a few parts per billion is required. While part of the BONO Group, ARTES Ingegneria is in the business of Deaerators since 1958.
The degassing process is achieved in the deaerating tower where make-up water is atomised on a set of special packing that increases the contact surface between water and steam. Oxygen and carbon dioxide are stripped by the steam flow and vented through a calibrated orifice. Deaerated water is collected in the storage tank so as to assure an adequate “Hold-up” time for the boiler downstream.
According to the design capacity and steam flow, the deaerating tower may be arranged on a vertical or horizontal geometry so that, in the latter case, a larger surface of mass and heat transfer is implemented.
Deaerators are manufactured and marketed on BONO Artes’ own proprietary design in order to assure the complete responsibility of the concerned unit.
|
|
The Deoxygenation system for injection water, can be delivered in two different versions; Minox DeOx System - 2 Stages, or Minox Deox System - Compact Tower.
The MinoxTM DeOx System - 2 stages :
This is the ultimate Deoxygenation system configuration available in the market today. It gives extremely small and light units and requires a minimum of maintenance and utilities.
The MinoxTM Deox System - Compact Tower:
By utilizing the MinoxTM process in conjunction with a tower and packing, the same technical features as the 2-stage system are achieved. It will however require more space and support than the 2-stage system, but still significant less than a conventional system. This means that overall, for most new installations, the 2-stage system will be more cost effective.
|
|
Seawater Deaerators
Edwards is a market leader in the manufacture of deaeration equipment. We offer a complete range of deaerators including seawater deaeration packages for use in water injection systems. These designs include conventional packed column vacuum deaerators and the unique Edwards patented spray packed vacuum deaerator, which uses the patented spray distributor technology in conjunction with high mass transfer efficiency packed beds. We can also provide inlet gas stripping, steam stripping and trace gas assisted deaerators.
|
|
The process is based on the patented and well-proven MinoxTM process. The process has been in use for offshore applications since 1991 and has now been introduced to the conventional industry with low capacity units.
The MinoxTM process gives small, compact and economical systems, also for this application. The most common industrial application for the conventional industry is Deoxygenation of water in cooling circuits, district heat plants etc.
|
|
OMVE DEA range deaerator systems optimize conditions by removing air and gasses, using controlled vacuums and temperatures instead of chemical stripping gases.
The OMVE DEA210 and DE2320 deaerator remove gasses from a broad range of products and were specifically designed for laboratory applications to simulate industrial deaeration processes and gain similar results on R&D or Pilot scale.
|
|
SIGMAVAC Deaeration Systems are used for the degassing of fruit and/or vegetable juice, sauces, viscous liquids, and other products.
Special designs are also available for the deaeration of honey, fruit and/or vegetable mashes.
Other advantages of the SIGMAVAC Deaerator system
* Quality improvement by removal of air before heat treatment.
* Improved appearance, color and shelf life of product after filling.
* Eliminates foaming at the filler.
* Complete recovery of volatile aromas.
* Pre-assembled skid mounted units are available for fast on site installation. They can be stand alone units or integrated with existing process equipment.
|
|
|
|
