... IV-20 .Module with Incremental-Encoderconnection (K0, /K0, K1, /K1, K2, /K2) .Four operating modes for adaptation to the signal source .Six output channels with adjustable output levels (5VDC, 11-30VDC) Electrical Data Operating Voltage ..................................................... ...
Input voltage: 220, 115 V
Output voltage: 24, 12, 15, 5 V
Current: 167 mA - 1,000 mA
The 5AC series is a switching AC-DC power supply available in a low profile 0.500″ height and in single and dual outputs. They offer excellent line and load regulation and is continuously protected against short circuits. The highly reliable module is ...
Pico Electronics
Input voltage: 115, 220 V
Output voltage: 12, 15, 24, 5 V
Current: 333 mA - 2,000 mA
The 10AC series is a switching AC-DC power supply available in a low profile 0.500″ height and in single, dual and triple outputs. They offer excellent line and load regulation and is continuously protected against short circuits. The highly reliable ...
Pico Electronics
Input voltage: 115 V
Output voltage: 5 V - 24 V
Current: 100 mA - 2,000 mA
The LAC series is a linear AC-DC power supply available in single, dual and triple outputs. They offer excellent line and load regulation and very low output ripple – 1mVRMS. The highly reliable module is capable of up to 10W power in a wide ambient temperature ...
Pico Electronics
Input voltage: 8 V - 80 V
The Smart Power Dump - PDA072 is JVL's own plug-n-play power supply optimizer, designed as an automatic power dump circuit and CVI control voltage power supply to protect both your motor and power supply. It eliminates back-emf issues and uses the same ...
JVL A/S
Input voltage: 90 V - 264 V
Output voltage: 24 V
Current: 2.8 A
... Switch Mode Power Supply PSU24-060 / PSU24-060-M12 ■ PSU Desktop ■ 24VDC, 2.8A ■ 60W ■ 90-264VAC ■ AC connector with earth ■ (Optional) with M12 connector Features : ■ Universal AC input/Full range ■ No load power consumption<0.3W ...
JVL A/S
Input voltage: 85 V - 264 V
Output voltage: 24 V
Current: 3.2 A
... High Quality Power Supplies A 120W switchmode power supply that are particularly well suited for supplying the range of JVL integrated servo and steppermotor or other driver/controller with 24 VDC supply voltage. Ultra compact with dimension 40x125.2x113.5mm ...
JVL A/S
Input voltage: 230 V
Output voltage: 6,500 V
Current: 6 mA
... The AF2WR power supply generates a high voltage, which is needed to run ionizers. The AF2WR power can feed up to 2 antistatic devices, has external Jack connec-tors, is mounted in a painted metal box, with ON / OFF control switch, signal lamp in service ...
Elettromeccanica Bonato sas
... The APS2 generates high voltage, which is necessary for the ionizers functioning. The APS2 power supply can power up to 2 antistatic devices, has external jack connections, is mounted in a painted metal box, with ON / OFF control switch, stand-by, ...
Elettromeccanica Bonato sas
... The APSX2 generates high voltage, which is necessary for the ionizers functioning. The APSX2 power supply can power up to 2 antistatic devices, has external jack connections, is mounted in a painted metal box, with ON / OFF control switch, stand-by, ...
Elettromeccanica Bonato sas
Input voltage: 220, 380 V
Output voltage: 310, 560 V
Power: 500 W - 15,000 W
... A power supply PSU is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load. Main ...
The UHV-750 Battery Internal Resistance Tester is a portable instrument for measuring battery internal resistance and terminal voltage using advanced AC discharge testing methods. It supports fast online measurements, data storage and analysis for efficient ...
Input voltage: 198 V - 242 V
Output voltage: 25 V - 250 V
Current: 15 A - 20 A
... Product introduction
Dedicated portable DC power supply for field operation testing and maintenance of high-voltage circuit breakers and their operating mechanisms. Provides an isolated DC output for on-site switch operation tests ...
Input voltage: 220 V
Output voltage: 0 V - 420 V
Output frequency: 40 Hz - 65 Hz
The UHV-930 precision program-controlled power supply is a programmable AC voltage and current source designed for inspection, calibration and production test applications. It provides low-distortion sinusoidal outputs with adjustable amplitude, phase ...
Input voltage: 230 V
Output voltage: 0 V - 30 V
Current: 3, 4 A
The concept of laboratory DC voltage sources, which has been proven over the years, is designed to power DC electrical devices in industry and education. The robust metal construction, linear regulation and constancy of parameters determine them for use ...
Diametral a.s.
Input voltage: 230 V
Output voltage: 0 V - 30 V
Current: 0.1 A - 4 A
The concept of laboratory DC voltage sources, which has been proven over the years, is designed to power DC electrical devices in industry and education. The robust metal construction, linear regulation and constancy of parameters determine them for use ...
Diametral a.s.
Input voltage: 230 V
Output voltage: 0 V - 40 V
Current: 0.1 A - 3 A
The concept of laboratory DC voltage sources, which has been proven over the years, is designed to power DC electrical devices in industry and education. The robust metal construction, linear regulation and constancy of parameters determine them for use ...
Diametral a.s.
... Introduction
Battery Diaphragm Gas Permeability Tester N600E is designed and developed according to GB/T 36363-2018 and related standards. It uses the differential pressure method for professional measurement of air permeability of battery separators, ...
... Battery membrane permeability tester / air permeability tester for lithium-ion battery separators ISO 5636.5 Gurley method for determining the air permeance of battery separator N600E Battery Separator Air Permeability Tester It can be used in quality ...
Input voltage: 208 V - 480 V
Output voltage: 0 V - 80 V
Current: 0 A - 170 A
The EA-ELR 10080-170 3U is a 3U rack-mounted programmable DC load from EA Elektro-Automatik, featuring energy recovery and versatile performance. It works as a 0-80V adjustable load and 0-107A variable current load, with 5000W rated power and 3000W derated ...
TPS Elektronik GmbH
Input voltage: 90 V - 264 V
Output voltage: 24 V - 28 V
Current: 4.2 A
The TPS100-GP24V is a 100W high-performance power supply belonging to the TPS010-100W GP Series din rail power supply, a versatile range that includes 10W/30W/60W/100W din rail power supply options to meet diverse industrial and medical needs. As a convection ...
TPS Elektronik GmbH
Input voltage: 90 V - 370 V
Output voltage: 12 V - 15 V
Current: 0.85 A
The TPS010-GP12V is a 10W high-performance power supply belonging to the TPS010-100W GP Series din rail power supply, a versatile range that includes 10W/30W/60W/100W din rail power supply options to meet diverse industrial and medical needs. As a convection ...
TPS Elektronik GmbH
Input voltage: 22 V - 26 V
Output voltage: 1 kV - 30 kV
Current: 0.5 mA - 20 mA
Wisman's PMB module is a special ultra-low noise, high stability, low ripple, and miniaturized module for photomultiplier tubes, mass spectrometers, and electron microscopes. The price is advantageous. When digital RS232, RS485 control and RS-485 bus ...
Wisman High Voltage Power Supply
Input voltage: 220 V
Output voltage: 1 kV - 130 kV
Current: 0.1 mA - 1,200 mA
Wisman's DL series high voltage power supply is a high-performance 19'' standard rack-mounted high-voltage power supply. DL series has a complete protection system,which can be controlled remotely or locally. Its front panel has voltage and current display, ...
Wisman High Voltage Power Supply
Input voltage: 4.5 V - 5.5 V
Output voltage: 0.05 kV - 0.3 kV
Current: 0.33 mA - 2 mA
... Wisman's MM miniaturized module with low-noise and high-stability is intended for photomultiplier tubes, mass spectrometers, and electron microscopes. The price is competitive. MM is a printed circuit board mounting high voltage power supply with small ...
Wisman High Voltage Power Supply
... RS-232 Interface/Software for curve decay variation during charging and discharging Storage Battery Systems Battery Capacity Testers, Check battery condition in seconds, with the battery in service! Test condition without shutting down battery Hold ...
... Test Condition Without Shutting Down Battery. Simultaneously Measure Battery Resistance, Voltage. Comparator Function. Rates Conditions as Pass, Warning, or Fail. Memory and Read Function Compact and Lightweight. USB PC Interface ...
Input voltage: 90 V - 240 V
Output voltage: 0 V - 40 V
Current: 0 A - 5 A
... • 4OVDC/5ADC wide range output. • Switching technology, analog quality. • 1+2 output 200W. • 1 programmable output (0-40V/0-5A), 2 fixed outputs (5V/2A and 3.3V/3A). • High resolution (lmV, imA), high stability and low drift. • Low noise and ripple ...
Input voltage: 85 V - 264 V
Output voltage: 12, 24, 48 V
Power: 120 W
... The AMM3 AC/DC stabilized power supply converts alternating current to direct current with a maximum power of 120W. - **Electrical Features:** - Switching power supply for input voltage 85 to 264 VAC. - Efficiency from 87 to 89% depending on models. ...
Lettel
Input voltage: 90 V - 264 V
Output voltage: 24, 48 V
Power: 240 W
... The AMM4 stabilized AC/DC power supply converts alternating current into direct current with a maximum power of 240W: - Electrical: Switching power supply for input voltage 90 to 264 VAC. Efficiency 87 to 88% depending on models. Output voltages ...
Lettel
Input voltage: 24, 48 V
Output voltage: 90 V - 264 V
Power: 480 W
The AMM5 stabilized AC/DC power supply converts alternating current into direct current with a maximum power of 480W:Electrical:Switching power supply for input voltage 90 to 264 VAC.92% efficiency on all models.Output voltages depending on model: 24V ...
Lettel
... PB-03 Air Permeability Tester is based on the differential pressure method (Oken Type), and is professionally applicable to the determination of air permeability of battery diaphragms, breathable films and other relative polymer products. - Product Features: - ...
... The Battery Diaphragms Gas Permeability Tester is based on the differential pressure method (Oken Type), and is professionally applicable to the determination of air permeability of battery diaphragms, breathable films, and other relative polymer products. - ...
Voltage: 185 V - 230 V
Energy capacity: 1,004.8 Wh
Power: 500 W
... Portable all-in-one inverter and energy storage solution integrating inverter, BMS and LiFePO4 battery for outdoor and emergency use.
Features
- Highly integrated inverter and BMS design, compact and portable
- Long-life
Ximai Electric (Wuhan) Co.,Ltd
Voltage: 320 V - 460 V
Energy capacity: 57.6 kWh - 64 kWh
Power: 15 kW
The ESS LV 15KW+64KWH is a three-phase low-voltage all-in-one energy storage system integrating inverter and BMS with grid-tie capability, built-in MPPT solar charger and support for large-capacity battery packs suitable for industrial and commercial ...
Ximai Electric (Wuhan) Co.,Ltd
Voltage: 85 V - 240 V
Energy capacity: 30 kWh
Power: 12 kW
The ESS 12KW30KWH is an all-in-one pure sine wave inverter and battery energy storage system integrating inverter, BMS and multiple charging options for residential and commercial applications. It supports grid-tie operation, generator input and provides ...
Ximai Electric (Wuhan) Co.,Ltd
Voltage: 50 V
Energy capacity: 13.4 kWh
Power: 6 kW
... E/Bick LV Home — Plug & Play residential energy storage solution
E/Bick LV Home is a plug & play energy storage system designed for residential self-consumption and homes with increased energy needs. The unit integrates the full energy capacity ...
Voltage: 173 V - 864 V
Energy capacity: 17 kWh - 345 kWh
Power: 9 kW - 45 kW
... E/Scal 6 is a modular, stackable lithium‑ion energy storage system for commercial and industrial applications, scalable from 17 kWh to 345 kWh and designed for self‑consumption, peak shaving and microgrids.
Key features
- Modular,
Output voltage: 230 V
... Overview
The LOCKEEL® e-bike charging station is designed for secure outdoor storage and simultaneous charging of batteries for e-bikes, pedelecs, electric scooters, power tools and other technical devices. The unit features four spacious compartments, ...
LOCKEEL s.à r.l.
Output voltage: 230 V
... Overview
The LOCKEEL® e-bike charging station secures and charges batteries for e-bikes, pedelecs, electric scooters and portable equipment in outdoor environments. Four individual compartments each provide two protected sockets to charge devices ...
LOCKEEL s.à r.l.
Output voltage: 230 V
Overview The LOCKEEL® e-bike charging station is designed for safe outdoor storage and charging of e-bike, pedelec and electric scooter batteries, as well as batteries for tools and technical equipment. It features eight individual compartments, ...
LOCKEEL s.à r.l.
... Highest level of protection Line conditioners have been designed to provide the highest level of protection to electrical appliances connected to distribution lines disturbed by sudden voltage variations, HF noises and spikes. Statistically, these phenomena ...
AUNILEC
Voltage: 24 V - 220 V
VIDI2 Controller Platform is powerful tool to set ideal parameters and monitoring architecture for critical AUPUS HE backup power systems. True redundancy principle of AUPUS power systems applies also for the controller, which means that controller can ...
AUNILEC
Input voltage: 230 V - 277 V
Output voltage: 24 V
Current: 5, 10 A
Uninterruptible Power supply unit for fire protection and voice alarm system, compliant with European standard EN54-4:1997+A1:2002 +A2:2006. The device integrates DC-Ups “All In One” CBI with different battery sizes and two independent outputs, controlled ...
AUNILEC
Input voltage: 230 V
Output voltage: 7 V - 12 V
Current: 200 mA
... supporting power supply of TRS system current efficiency 200 mA TRS-09a is a supporting power supply for the TRS System which supplies stabilized direct voltage 11,5V. It can work in two modes: as a controlled supply (switched on with external ...
SIMEX Sp. z o.o.
Input voltage: 90 V - 375 V
Output voltage: 24 V
Current: 0.4 A
... can be installed on DIN rail TS-35 LED indicator for power on plastic case protections: short circuit / overload / over voltage convection cooling The SPS-24/0,4 is part of the DIN rail power supply series, which is designed ...
SIMEX Sp. z o.o.
Input voltage: 90 V - 375 V
Output voltage: 24 V
Current: 1.25 A
... can be installed on DIN rail TS-35 LED indicator for power on plastic case protections: short circuit / overload / over voltage convection cooling The SPS-24/1,2 is part of the DIN rail power supply series, which is designed ...
SIMEX Sp. z o.o.
Sonacme technology's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion. This ...
... Temperature controlled battery short circuit tester This equipment is designed based on the requirements of various battery short-circuit test standards. According to the standard requirements, the short-circuit device must meet the internal resistance ...
The battery pack external fire test machine is mainly used for the safety verification test of PACK level battery packs or systems and structural parts, and is used to evaluate the safety performance of the battery. The external fire of the battery pack ...
The tester is designed for synchronous balancing of multiple string groups, with how many string groups are connected to work together to improve balancing efficiency, ensure that each string group voltage is consistent, and achieve optimal battery recovery ...
Input voltage: 80 V - 300 V
Output voltage: 48 V
Current: 150 A
The iBAN Power EPS48125 is a 19” 2U rack-mounted 48V hybrid power system designed for telecom applications. It delivers up to 150A output current with modular rectifiers, achieving over 96% conversion efficiency. The system integrates solar, grid, and ...
IBAN POWER
Input voltage: 90 V - 280 V
Output voltage: 48 V
Current: 30 A
The iBAN Power OPS1500 is a 48V DC power system designed for outdoor telecom sites such as micro base stations and remote radio units (RRUs). It features an IP65-rated aluminum enclosure with natural cooling and delivers up to 1500W output power with ...
IBAN POWER
Input voltage: 85 V - 290 V
Output voltage: 48 V
Current: 60 A
... The iBAN Power EPS4860 is a 19” 1U rack-mounted 48V power system designed for fiber transmission, microwave stations, and access switches. It supports up to 60A output current with 3×1kW rectifier modules, each delivering over 95% conversion efficiency. Key ...
IBAN POWER
Proxy Tester is a portable instrument created to satisfy the needs of both installers as well as retailers. It makes it possible to control correct functioning of any D.C. sensor or magnetic sensor even when lacking expensive sophisticated instrumentation ...
150g 6ms acceleration mechanical shock test equipment mainly applicable to shock resistance tests in such fields as electronic products,aerospace, shipping, military industry, automotive parts and transportation. shock tests in form of half sine wave, ...
AI SI LI (China) Test Equipment Co., Ltd
High Acceleration Mechanical Shock Testing Machine for Lithium Battery is designed for measuring and ensure shock performance of products and packages. It can do normal shock test with half sine wave, square wave, sawtooth wave etc., simulate products ...
AI SI LI (China) Test Equipment Co., Ltd
... With more and more photovoltaic applications and larger scale of power stations, more and more problems of solar cell modules have been exposed, such as power reduction, poor insulation and delamination. After years of research, it has been found that ...
AI SI LI (China) Test Equipment Co., Ltd
The ERT 580 is an earth resistance tester, manufactured by Tepcel. This product is operated with three earth ranges, such as 20, 200, 2,000 Ohm that can measure down to 0.01 Ohm. It is equipped with 2mA RMS one test current and 2 or 3 terminal measurement ...
Tecpel Co., Ltd.
The TecPel Linear D.C. power supplies have the following features and benefits: triple output, auto tracking, an auto series and parallel operation, a constant voltage and constant current operation, a low ripple and noise operation and an overload and ...
Tecpel Co., Ltd.
... 30V/3A DC Power Supply(30V/3A *2 ; 5V/3A *1) GPS -3303 is a 3-channel linear DC power supply with 195W output. Overload and polarity reversal protection and output control switch can protect GPS and load from accidental damage. Each channel has a high ...
Tecpel Co., Ltd.
... The PST-100 230V high frequency hand-held AC spark tester provides a quick and cost effective method of inspection on thick coatings and linings. Coating thicknesses of between 3mm and 30mm can be tested. The PST-100 is widely used for testing butt-welded ...