Carbon seals

Used primarily for banding round cable, Flat Seal BAND-FAST allows for consistent location banding on cable and casing. The short, flat seal is ideal for the lowest profile downhole applications.

Temperature limit: -30 °C - 260 °C
Outer diameter: 1 in - 28 in

PEEK Seal Material When reliability is non-negotiable, turn to PEEK (Polyether Ether Ketone) Seal Material. Engineered for excellence, PEEK seals combine exceptional durability, chemical ...

Temperature limit: -55 °C - 125 °C
Shore A hardness: 70 unit

Connector gaskets are made of a low compression force foam core, bonded over with conductive fabric and shaped like customer’s drawings. Ni/Cu standard or Ni/Cu with Carbon protection coating fabric bonded ...

... the inner rubber seal from being over compressed and eliminating gaps to create a form-fitting seal. USZL Thread Seals USZL thread seals differ slightly from other ...

Temperature limit: -50 °C - 200 °C
Pressure limit: 0 Pa - 2,800,000 Pa
Diameter: 6 mm - 330 mm

... lip and carbon face seals prone to leakage. Original designs were based on conventional high pressure lip seals. Over time the demands increased to zero leakage and extended seal ...

... spring. CRWH1: Seal with a double steel case, SKF WAVE lip and a carbon steel garter spring. CRWA1: Seal with a single steel case, SKF WAVE lip, a carbon steel ...

... unique challenge for bearing protection. As the carbon rings containing the steam wear, high temperature / high velocity steam travels down the shaft directly at the bearing seal. Standard OEM labyrinth ...

Temperature limit: 500 °C - 800 °C
Pressure limit: 3 bar
Diameter: 4,000 mm

... = up to 40 m/s (131 ft/s), depending on seal diameter Radial movement: up to 50 mm (1.97 “) Axial movement: theoretically unlimited Project specific special designs possible. Materials Seal ring: ...

Diameter: 10 mm - 200 mm

... and non-standard seal faces, tailor-made parts according to the customers’drawings or samples are all available from us. Materials include, Silicon Carbide (SSIC & SiCRB), Tungsten Carbide (6% Nickel TC & 6% Cobalt ...

Temperature limit: -200 °C - 260 °C
Pressure limit: 15 MPa - 250 MPa
Speed: 2 m/s

... Rings are used only for low to medium loads. For higher load requirements, filled PTFE materials (with glassfibre, bronze, carbon, etc.) have to be used. For sealing against high pressures, Back-up Rings made from specially ...

Temperature limit: -40 °C - 200 °C

Re/Re1Dust Seal for Motor Spare Parts 12*26*3.5 12x26x3.5 Gamma seals happen when the axial force of the lip comes into contact with the housing.The metal parts protects the rubber axial lip form exernal ...

Temperature limit: 500 °C
Pressure limit: 10 Pa
Diameter: 20 mm - 250 mm

Chamber Shaft Seal The high-performance shaft seal RotaSeal KD-3 is an economic shaft seal. Because of its modular system, the single parts can be assembled according to the various ...

Temperature limit: max 450.0 °C
Pressure limit: max 2.0 bar
Diameter: max 5000.0 mm

... materials casing, carbon fiber layer) Improved lifetime Bi-directional HELICOCARB® Seal close up HELICOCARB® Seal front view HELICOCARB® Seal HELICOCARB® ...

... 22mm Rotary Ring Carbon (Graphite/SiC/TC) Stationary Ring (SiC/TC) Bellows Other Parts(VION/SUS304/SUS316) GFK suitable pump CR,CRI,CRN 1,3,5 CR,CRI,CRN 10,15,20 CR,CRN 32,45,64,90 C... TB GFK dimension : 22mm ...

Temperature limit: -40 °C - 149 °C
Pressure limit: 300, 150 psi
Diameter: 2 in - 20 in

... ±0.5% typical Wetted Components End Plate Material: Carbon steel, 316L SS, PVDF, Acetal Flexible Liner: Buna, PTFE, EPDM, Natural rubber, and Viton® Non-Wetted Components Body: Carbon Steel, ...