Spray nozzles

Orifice diameter: 20 µm - 60 µm

Vortec Spray Nozzles provide ultra-fine droplet-sized sprays for evaporative cooling, atomization, humidification and wetting. Superior to conventional hydraulic and piezoelectric nozzles, ...

Orifice diameter: 20 µm - 200 µm

Vortec Spray Nozzles provide ultra-fine droplet-sized sprays for evaporative cooling, atomization, humidification and wetting. Superior to conventional hydraulic and piezoelectric nozzles, ...

Orifice diameter: 60 µm - 200 µm

Vortec Spray Nozzles provide ultra-fine droplet-sized sprays for evaporative cooling, atomization, humidification and wetting. Superior to conventional hydraulic and piezoelectric nozzles, ...

Orifice diameter: 0.25, 0.13, 0.5 in
Flow: 2.6 us gal/h - 231 us gal/h
Pressure: 0.7 bar - 6.9 bar

EXAIR's 1/8 FNPT, 1/4 FNPT and 1/2 FNPT no drip internal mix narrow angle round pattern nozzles are excellent for spraying a concentrated mist of liquid and positively stopping liquid flow when the compressed ...

Orifice diameter: 0.25, 0.13 in
Flow: 0.4 us gal/h - 1.9 us gal/h
Pressure: 0.7 bar - 4.1 bar

... needed over a wide band. Flow rate is adjustable via the adjusting valve. Siphon nozzles work best with a suction height of 36" (914mm) or less. Since these nozzles are siphon fed, the compressed airflow ...

Orifice diameter: 0.5, 0.25, 0.13 in
Flow: 0.5 us gal/h - 68.3 us gal/h
Pressure: 0.7 bar - 5.5 bar

... pattern nozzles are great where no liquid pressure is available and a thin coating is needed at a specific area. Flow rate is adjustable via the adjusting valve. Siphon nozzles work best with a suction ...

Orifice diameter: 0.25, 0.34, 0.13, 0.19 in
Pressure: 0 psi - 200 psi
Media temperature: 0 °C - 371 °C

... utilize unique vortices and flow passages to provide a finely atomized hollow cone spray pattern. When used with most normal fuels, Spin Jets produce a 70° cone angle spray with differential pressure ...

Orifice diameter: 0.05 mm - 0.41 mm
Pressure: 50 psi - 200 psi
Media temperature: 80 °F

Atomizing nozzles are available in both air-assisted and airless designs. They provide a specified spray pattern that can be used to assist in combustion in fuel systems or for applying a coating in medical ...

Orifice diameter: 0.07 mm
Pressure: 10 psi - 200 psi
Media temperature: 200 °F

Dispensing nozzles are designed for low volume dispensing, ranging from nanoliter droplets to precise dosing of milliliters at a time. These dispensing nozzles are available with orifice sizes as small ...

... Dual-Shaping Air Larger range of spray patterns Improved cleanliness Increased transfer efficiency Improved Production Uptime Dual Purge capabilities reduces color change time New fluid nozzle ...

... atomizers focused on delivering improved spray pattern control, cleanliness of the applicator during operation, and longer lasting components. The applicator can be used electrostatically for solvent-borne spraying ...

... mounted rotary atomizers focused on delivering improved spray pattern control, cleanliness of the applicator during operation, and longer lasting components. The applicator is designed to spray waterborne ...

Orifice diameter: 2 mm - 10 mm
Flow: 0.3 l/min - 222.7 l/min
Pressure: 0.5 bar - 10 bar

GA FLAT FAN NOZZLE – SHORT BODY The special short body design of the GA flat fan nozzle makes it possible to use nozzle spray pipes in such machines or systems where ...

Orifice diameter: 0.28 mm - 12.5 mm
Flow: 0 l/min - 223 l/min
Pressure: 0.5 bar - 10 bar

GX FLAT FAN NOZZLE – LOW CAPACITY GX flat fan nozzle tips are usually mounted onto a pipe by means of a welded nipple or a clamp, and secured in place with a retaining nut. They can ...

Orifice diameter: 0.38 in - 0.75 in
Flow: 0.8 l/min - 223 l/min
Pressure: 0.5 bar - 10 bar

... flat fan nozzle tips are usually mounted onto a pipe by means of a welding nipple and secured in place with a retaining nut. Therefore, they can be easily replaced and their dovetail connection assures ...

Orifice diameter: 0.15 mm - 0.6 mm
Flow: 0.14 l/min - 1.95 l/min
Pressure: 100 bar

Tip sizes to be defined depending on applications SF Airless Flat Tip SS Body The reference nozzle in the wood and Leather industries Robotic applications

Orifice diameter: 0.15 mm - 0.6 mm
Flow: 0.14 l/min - 1.95 l/min
Pressure: 100 bar

SF Airless Tip SS Body The reference nozzle in the wood industry Robotic applications, easy clean

Orifice diameter: 0.007 in - 0.061 in
Flow: 0.18 l/min - 13,700 l/min
Pressure: 5,000 psi

... Reversible/Switch Tips Designed to fit most manufacturers guards (exception, Graco RAC X) The quality of your work is only as good as the quality of your finish. Don't compromise on quality, choose the Exitflex, ...

Orifice diameter: 19 mm
Flow: 45 l/min
Pressure: 5 bar

AdBlue/DEF nozzles with stainless steel and thermoplastic versions available. Depending on the model they can be manual or automatic, with spike or thread connection.

Coaxial Nozzle Flat Cone 60° Coaxial Nozzle for air/oil lubrication systems.

These special nozzles are specific for band saw that allows lubricating both the working area and the side surface. Available with: - 1 inlet and 3 outlet - 2 inlets and 5 outlets

Threated coaxial nozzle with cone shape spray Coaxial Nozzle with head threaded and shape spray

Pressure: 3 bar - 6 bar
Media temperature: -25 °C - 80 °C

... bar. Think of tools, extruding plastics, lubricants, polishing, etc. The higher the pressure, the finer the spray mist and the smaller the spray angle. How it works: The fluid hose is either laid ...

Pressure: 3 bar - 6 bar
Media temperature: -25 °C - 80 °C

... metal hose - For low and high viscosity fluids To atomize low and high viscosity fluids (max. viscosity 420 mm²/s). The spraying angle on this atomizer is 90° in reference to air and fluid connection. Operating pressure ...

Pressure: 3 bar - 8 bar
Media temperature: -25 °C - 80 °C

... fixed a little above the maximum fluid level in the tank. With compressed air applied, the atomizer will instantly start to spray (a built-in check valve in the hose prevents the fluid level from dropping too fast). The ...

Orifice diameter: 0.3 mm - 10 mm

Brass nozzles 12 holes, air clockwise Nozzle body completely made of brass 12 circularly arranged spray air bores Glue hole diameter 0.3 to 1.0 mm

Orifice diameter: 0.2 mm - 1.6 mm

... two different spray distributions: uniform spray distribution throughout spray pattern area (when spraying at a low air-water ratio), or a mountain-shaped distribution ...

Lance Nozzle, good for complete evaporation in cooling tower, large volume is also effective for dust suppression. Features • Pneumatic spray nozzle producing fine atomization with ...

Orifice diameter: 0.2 mm - 5.8 mm

Standard Flat Spray Nozzles - One-piece Structure with Ceramic Tip Even Spray Distribution Features • Flat spray pattern with uniform distribution ...

Spray nozzles Eductor nozzle Misting nozzles Washing - cleaning nozzles

... when coming into contact with the vibrating surface. The ultrasonic nozzle produces droplets or particles of mastered size: the higher the ultrasonic frequency, the smaller the aerosol particles (some ...

Needle, nozzle Air Cap Set For 1500 Code: 1500NNK-1.6 Category: Paint Guns Sub-category: Suction spray Needle, nozzle Air Cap Set For 1500

SPRAY CHARACTERISTICS Fine atomisation of many liquids that cannot be atomised by hydraulic pressure alone. Uniform solid cone. Spray angle varies with air pressure and flow. Separate metering ...

Spray Characteristics The Delavan AL air atomising series spray nozzles offer the user a wide variety of spray patterns, flow rates and atomisation. Unlike hydraulic ...

The AL 15 series is a pressure-fed external mix flat fan spray nozzle The external mix feature allows control of the atomization without changing liquid flow. The lighter the air pressure, the higher ...

Orifice diameter: 1 in
Flow: 25 l/min - 250 l/min
Pressure: 6 bar

... that any debris is flushed from the nozzle to avoid pattern disruptions or flow reductions. All the models include a pressure eliminator for ease of flow settings at different pressures. Stream Pattern: The nozzle ...

Orifice diameter: 4, 8, 15 mm

The internationally patented Variacor® system enables you to assemble spraying systems quickly and easily as well as adjusting nozzle positions efficiently. Economy: You don't waste time calling ...

Orifice diameter: 4 mm - 8 mm

Thread Mount Type The Coolant Spray Nozzle could easily adjust its direction and spray precisely. BA90102020001A Thread Mount: PT 1/8 L: 20 L1: 10 D1: 6 D2: 5 d: 4 H: 17 BA90102020002A Thread ...

Orifice diameter: 3 mm - 4.4 mm

The Coolant Spray Nozzle could easily adjust its direction and spray precisely. When the coolants correspond with three pressures-low, medium and high pressures, it can precisely aim ...

Leak Lock Type (Alloy Steel) Special design for avoiding oil leaking. Not delaying spraying fluid which prolongs the longevity of the tool holders. SPECIFICATIONS BA90104020001A Thread Mount: PT 1/8 L: 40 L1: ...

WS single nozzle can accurately spray to the lubrication point position to achieve precise lubrication.

WD dual nozzles, the center distance of the dual nozzles is 7, 9, 11mm, whichWD dual nozzles, the center distance of the dual nozzles is 7, 9, 11mm, which can be accurately ...

60 ° concentric tube oil-gas nozzle is widely used in micro lubrication spray oil coating, such as oil coating on metal plate surface.

... mm can be used for flat or round spray application. It is optionally possible to place connections for three feed hoses (spray air, control air, sprayed material) on the top or the side of the nozzle. Spray ...

The Triple Click Nozzle that was developed by Dosanova replaces the traditional foam, rinse and desinfection nozzle. Just by turning the head 120° the operator can easily switch between the 3 nozzles ...

The Triple Click Nozzle that was developed by Dosanova replaces the traditional foam, rinse and desinfection nozzle. Just by turning the head 120° the operator can easily switch between the 3 nozzles ...

FOAM/RINSE/DISINFECTION NOZZLE Stainless steel nozzles with ST3100 Nipple

Orifice diameter: 0.5 in - 1 in
Flow: 80 l/min
Pressure: 3 bar

Nozzle made of polypropylene Housing and internal parts made of polypropylene, valve seat and O-rings made of FKM or EPDM, spring of hastelloy 2.4610, rotatable hose connection. Viscosity: 800 mPas*

Orifice diameter: 0.5 in - 1 in
Flow: 80 l/min
Pressure: 3 bar

Housing and internal parts made of polypropylene, valve seat and O-rings made of FKM or EPDM, spring of Hastelloy 2.4610, rotatable hose connections.

Orifice diameter: 1, 0.75 in
Flow: 100 l/min
Pressure: 2 bar

Housing and internal parts made of white polypropylene, valve seat and O-rings made of NBR, spring made of stainless steel.

... containers made of HDPE Newly developed, high quality nickel-plated double pump mechanism with angled, rotating swivel Atomizing thin oils, petroleum and other fluids in any position 300 ccm

Media temperature: 450, 350 °C

Heating nozzles for injection machines and molds, hot melt application, similar spray gun, especially in cases where they are available for mounting in limited areas DESCRIPTION: • Power dissipation: ...