|
|
Control and serial communication options, encompassing Rotork’s proprietary Pakscan and open systems including Profibus, Foundation Fieldbus, Modbus and DeviceNet, complete an unbroken chain of Rotork reliability from the valve to the control room and, via Ethernet, to anywhere on the planet.
Provides intelligent communication options and a multilingual display. The IQ actuator range offers multi-turn and quarter-turn isolating/regulating duty.
Torque range 14 to 3,000 Nm (10 to 2,200 lbf-ft) direct drive (multi-turn only). Higher torques when combined with IS or IB gearbox, up to 40,800 Nm (30,000 lbf-ft). Quarter-turn when combined with IW gearbox up to 250,000 Nm (185,000 lbf-ft).
•Complete integrated motor control.
•Simple non-intrusive, infra-red setup and adjustment.
•Digital, analog or bus system remote control and status reporting.
•Comprehensive software tools for plant records and valve performance analysis.
|
|
Series 700 actuators are pneumatic diaphragm operators that offer spring return in either direct or reverse acting styles, offering fail-open and fail-closed modes respectively.
The actuators may be fitted with a variety of springs in order to overcome the wide range of forces that may exist on a valve plug. An adjusting mechanism is incorporated into the actuator design to allow for adjustment of the spring pre-compression.
The series 700 actuator is available in 60, 100 and 160 square inches of effective diaphragm area and may accommodate up to five inches of travel.
|
|
Available in double-acting and spring-return configurations The RC range is an extremely compact pneumatic actuator. Its scotch yoke design is particularly suited for valves with high start or end torque requirements. With torque output up to 4,400Nm (38,700 lbf-in)
The RC200 range is available in a variety of configurations and an extensive range of options and accessories is available.
|
|
Double acting actuors PETRAS
Double acting pneumatic actuators up to 10 000 Nm at 5 barg supply pressure.
rotation : 90° - 120° -180° - 240°
Materials
- high grade aluminium
- cast iron
- carbon steel
- stainless steel
Hydraulic version available up to 200 barg supply pressure
Established in 1966, PETRAS is a pioneer in the design and manufacture of high performance pneumatic and hydraulic actuators for quarter turn valves.
|
|
Smart quarter-turn actuator with the torque 50Nm to 1000Nm.
AVAR adopts liquid crystal display system with Chinese or English available indicating valve position,real time torque,working status, local/remote operation, error alarm etc.
|
|
RUGGED, LOW COST electric actuators FOR ROTARY VALVES
Thre on-of models wit h 100, 300 or 600 lb-in Output torque
wATERprof (nema 4, 4x, ip 65) Bray Controls' generations
of innovative electric actuators have a proven record of success.
Building on this record, Bray has combined
engineering expertise and years of field experience
to produce the R5. This red, rectangular electric
actuator for rotary valves delivers highly reliable
service at a reduced price.
The R5 meets the needs of 21st Century industrial applications
at a price that is unmatched.
|
|
Double motor actuator M76348
Torques: 750, 1500 or 3000 Nm
• with control and high-speed motor
Speeds: Modulating for 5 or 10 rpm
High speed for 20 or 40 or 80 rpm
• mode of operation to DIN VDE 0530, Part 1,
in closed-loop control operation: intermittent duty
S4/S5 -10%ED - 1200c/h for control motor < 3 kW
S4/S5 -10%ED - 600c/h for control motor > 3 kW
in high-speed operation: short time duty S2 – 5 min
• hand wheel for emergency operation
• mounting flange and drive shaft, type D to DIN 3210
(free end shaft with featherkey)
• Temperature range –20 to +60°C
• self-locking
|
|
Electric Oden P30L, P50L and P220L control valve actuators for linear applications.
High precision through the Oden Gear System.
Fits most types of valves using ASAB standardised linear modules and assembly kits
Voltage 24 VDC.
Analogue control 4-20 mA or digital.
Force up to 40 kN.
Standard stroke 40/100
|
|
type ST 0
Max. load thrust: 4 000 [N]
Switching-off thrust: 4 500 [N]
Operatings speed: 4 to 40 [min-1]
Operating stroke: 8 to 40 [mm]
Ambient temperature: -25 to +55 [°C]
Protection enclosure: IP 54 (67)
Operating position: any position
Weight: 2,5 to 4,5 [kg]
Standard equipment
· Voltage 230 V AC
· Terminal board connection
· Control part executions:
o 1 thrust switch + 1 position switch
o 2 thrust switches
· Pillar mechanical connection
· Mechanical position indicator
· Manual control
|
|
|
|
|
|
Description standard features
• intermittent duty S4 / S5 min.25% duty cycle, 1200c/h
acc. to DIN EN 60034, protection class IP67
• motor insulation class F, temp. range -20°C to +60°C
(-4°F to +140°F)
• „non intrusive“ for PROFITRON (after adjustment of the
end positions of the valve)
• hand wheel for emergency operation (disconnected
during normal operation)
• PROFITRON: 3 reference force-stroke of the valve can
be stored
• electronic motor protection, automatic phase sequence
correction
• frequency range of the power supply 47 to 63 Hz
• 24 V DC supply for electronics unit possible
• analog actual position value (0/4...20mA)
• travel limits continuously adjustable
• force dependent cut-off adjustable in 10% steps from
70% to 100% Fmax.
• travel speed adjustable in 7 steps,
step-up distance factor 1.4
• self-acting cut-off (depending on cut-off force, travel
distance, etc.)
• soft starting for high positioning accuracy (starting
current less then rated current)
• indication that actuator is in operation
• separate mounting of the electronics unit possible
• external screws stainless steel
• documentation in German/English: operating instructions
• programming by customer possible
|
|
Modulating actuator 2SB6...
• Force 2 to 25 kN
• Stroke 10 to 100 mm
• positioning speeds 13,5 to 50 mm/min
Standard design
• intermittent duty S4 min. 30% duty cycle max 600 c/h
S5 min. 30% duty cycle max 600 c/h
• optional: short-time duty S2-2 min for open-loop control
• duty acc. DIN VDE 0530, part 1
• Temperature range –20 to +60°C
• Protection class IP 65 acc. to DIN 40050 / IEC529
• hand wheel for emergency operation (disconnected
during normal operation)
• preloaded belleville springs to maintain the closing force
->Minimum axial driving rod vibration in case of
unfavorable flow conditions in the valve
• double-acting, coercive controlled, load dependant
tripping in the end positions and the stroke
->Damage protection for the valve in case of eg.g debris
between the valve seat and the valve trim
• absolute self-locking of the driving rod
• optional position electronics
|
|
|
|
|
|
PNEUMATIC ACTUATOR EB-EW, SINGLE-ACTING
FEATURES
- Maintenance-free, continious lubrication
- Suitability for valves with an angle of 90°
- Blow-proof shaft bearing
- Torques in agreement with EN ISO 5211
- Control pressure min. 2 bar, max. 10 bar
- Good visible elastic position indicator
- Function return by turning the supply plate:
Currentless - close
Currentless - open
- All elements of connection are made of stainless steel.
Possibilities of mounting and accesories are shown in chapter 4.3.
GENERAL APPLICATIONS
- Water and wastewater technology
- Shipbuilding
- Swimming pool technology
- Bulk handling
- Pneumatic conveying systems
- Chemical industry
TECHNICAL DATA
Torque: 35-1368 Nm (control air pressure 6 bar)
Final position: adjustable to +/- 3°
Limit switch and solenoid
valve mounting: VDI / VDE 3845
Control pressure: min. 3 bar, max. 10 bar
Control air: clean and dry air
at circuits $ 2/min please lubricate
Temperature range: - 20/+85 °C
Valve interface: EN ISO 5211
Actuator cylinder: Aluminium, hard anodized.
Other coatings upon request.
|
|
New in 2008, the J3 Series part turn electric rotary valve actuators from J+J, the leaders in actuator innovation, introduces an LED status light in the cover to give continuous visual status information advising if the actuator is functioning correctly, is in manual mode, or has stopped because the valve is blocked.
The J3 also offers plug & play function conversion kits to change the standard on-off function to either failsafe or modulating, or both.
|
|
type SP 1
Max. load torque: 80 [Nm]
Switching-off torque: 90 [Nm]
Operating time: 10 to 80 [s/90°]
Operating angle: 60° to 360°
Ambient temperature: -25 to 55 [°C]
Protection enclosure: IP 65
Operating position: any position
Weight: 6,5 to 8,3 [kg]
Standard equipment
¤ Voltage 230 V AC
¤ Terminal board connection
¤ 2 torque switches
¤ 2 position switches
¤ Mechanical stop ends
¤ Connection with valve flanged ISO 5211
¤ Mechanical position indicator
¤ Manual control
Additional equipment
¤ Voltage 24 V AC, 24 V DC, 3x400 V AC
¤ Connector connection
¤ 2 additional position switches
¤ Position transmitter with the following type of signal:
- resistive 1x100 [ohm], 1x2000 [ohm], 2x100 [ohm], 2x2000[ohm]
- current from R/I converter 4 to 20 [mA] with/without power supply
- current (a capacitive transmitter) 4 to 20 [mA]
¤ Position controller 0/4 to 20 [mA], 0 to 10 [V]
¤ Space heater
¤ Space heater's thermal switch
¤ Electric local control
¤ Version with stand
¤ Version with lever
¤ Pull-rod
|
|
Standard actuators 2SC50.. 150 to 4300 Nm
Modualting actuators 2SC55.. 250 to 3400 Nm
Positioning speed ranges: 20 to 160 sec/90°
Mechanical connection: ISO 5211, base & lever
For torques exeeding the standard ranges, combinations of 2SA5 rotary actuators and larger
worm gearboxes are utilized (up to 360,000 Nm).
SIPOS 5 Flash
• Integrated frequency converter
• Upgradeable functionality
• Valve protection
• High positioning accuracy
• Variable positioning times
• Modular design
• minimal type variance
|
|
Part-turn Actuator AVAT/AVATM01 - AVATM06 are installed on the automation of ball valves and butterfly valves.
Part-turn Actuator AVAT/AVATM01 - AVATM06 can be combined with lever if it is required.
Part-turn Actuator AVAT01 - AVAT06 torque range is from 125Nm to 2000Nm (90ft-lbf to 1475ft-lbf)
·Voltage Supply: 220Vac ~ 460Vac, 50Hz/60Hz, single or three phase.
·Enclosure Protection: IP68, Double-seated structure.
·Isolation: Class F, Class H (optional)
·Optional Function:
Modulating I/O signal 4-20mA
Explosion Proof
Fieldbus System: Modbus, Profibus, etc.
|
|
Electric Oden P30R3, P50R, P220R and P500R control valve actuators for rotary applications.
High precision through the Oden Gear System.
Fits most types of valves using ASAB standardised turning modules and assembly kits
Voltage 24 VDC.
Analogue control 4-20 mA or digital.
Torque up to 400Nm.
|
|
RACO's turn and part-turn valve actuator is a completely electromechanical final control element for operating fittings, valves and flaps, etc. with rotational movement ranging from less than 1 revolution to several revolutions.
The DM IV is assembled from components of the same proven building block system from RACO's electric actuators. This allows us to offer every customer the special turn and part-turn valve actuator for his needs at a low price.
The DM IV consists of the gear, motor and accessories.
|
|
Standard 2SA50.. 10 to 4000 Nm
Modulating 2SA55.. 15 to 2800 Nm
Speed ranges 1,25 bis 160 1/min
mechanical connection DIN ISO 5210 oder
DIN 3210
SIPOS 5 Flash
• Integrated frequency converter
• Upgradeable functionality
• Valve protection
• High positioning accuracy
• Variable positioning times
• Modular design
• minimal type variance
|
|
Multi-turn Actuator AVA01 ~ AVA10 are installed on the automation of Globe valves, Gate valves, sluice valves, penstock and some dampers.
AVA01 ~ AVA10 combined with BA bevel gearbox for large torque valves.
AVA01 ~ AVA10 combined with ZJ worm gearbox for large torque ball valves, butterfly valves and dampers.
Multi-turn Actuator AVA01 ~ AVA10 torque range is from 45Nm to 2500Nm (35ft-lbf to 1843ft-lbf). For higher torque, they shall combined with BA bevel gearbox or ZJ worm gearbox.
-Voltage Supply: 110Vac ~ 660Vac, 50Hz/60Hz, single or three phase.
-Enclosure Protection: IP68, Double-seated structure.
-Isolation : Class F, Class H (optional)
-Output Speed: 18/21rpm ~ 96/115rpm,
-Optional Function:
Modulating I/O signal 4 - 20mA (AVAM01 ~ AVAM06)
Explosion Proof
Fieldbus System: Modbus, Profibus, etc.
|
|
AUMA offers a range of actuators meeting virtually any valve automation requirement. A wide range of multi-turn actuators from 10 Nm through 32,000 Nm, part-turn actuators from 25 Nm to 360,000 Nm or linear actuators from
3,8 kN to 217 kN are available.
Various types of valves can be operated by rotation, swivel and linear movements.
|
|
Electric Actuator Type EA11
The EA11 is our basic version for the open-close operation of smaller torques. The electric actuator EA11 consists of a gear, a direct current motor, a base print as well as equipment for end stops in its standard version.
Electric Actuator Type EA21/31/42
The electric actuators EA21, EA31 and EA42 are not only excellent equipped but can make their point with very high torques. Therefore these actuators can be used to actuate a wide range of valves.
|
|
EAU Series
For use with Ball Valves up to 2"
Series EVR
For use with all sizes of Ball Valves and Butterfly Valves up to 4"
Series EJM
For use with all sizes of Ball Valves and Butterfly Valves up to 24"
Series EVS / EVT
For use with all sizes of Ball Valves and Butterfly Valves up to 12"
|
|
J+J are first to market in their class with the new J3 Series IP65 weatherproof reversible part-turn electric actuators, introducing an LED light in the cover to provide continuous visible actuator status information, and with different flash sequences, provides simple and instant fault diagnosis. Also a first, is the function conversion kits which retro-fit to covert on-off function to either failsafe or modulating, or both.
The features compliment the retained functionality from the J2 Series actuators including multi-voltage capability and electronic torque limiting with auto gear relaxing, which were firsts in 2003 when the J2 was launched
|
|
KZCO's heavy duty actuator, the EH5, has an operating range of up to 500 in-lbs. Use the EH5 on KZValves that include stainless steel and butterfly valves ranging in size from 1.5" through 6".
FEATURES:
- High quality, durable actuator housing rated:
NEMA 6P - Waterproof tested
NEMA 7D - Ignition Protection tested
- Wiring options include on/off, flow control, pot feedback and 4~20mA
- 12/24 VDC and 24 VAC compatible
- RoHS compliant solid state programmable circuitry
- Up to 500 in-lbs torque
- Tough aluminum gear box with metal gears
- Waterproof plug connectors
- Many different functionality variations
- NFPA 1901 compliant for fire industry use
- Private labeling available
- Customization available for your specific application!
|
|
"EH2" Medium Torque Actuator - Recommended for KZValves 3/4" to 3".
FEATURES:
- High quality, durable actuator housing rated:
NEMA 6P - Waterproof tested
NEMA 7D - Ignition Protection tested
- 12/24 VDC and 24 VAC operation available
- Available cycle times - .5 seconds to 8 seconds
- Hundreds of wiring combinations available
- Many different functionality variations
- 60 to 275 in-lbs torque
- Tough aluminum gear box with metal gears
- Actuator housing available with "indicator flag" or with "blank" lid
- Waterproof wire plug connectors
- Mountable at any angle
- 110V operation with AC adapter
- Private labeling available
- Customization available for your specific application!
|
|
"EH3" Compact, Low Torque Actuator - Recommended for KZValves 1/4" to 1".
FEATURES:
- High quality, durable actuator housing rated:
NEMA 6P - Waterproof tested
NEMA 7D - Ignition Protection tested
- 12/24 VDC and 24 VAC operation available
- Available cycle times - .8 to 12 seconds
- Hundreds of wiring combinations available
- Recommended for KZValves 1/4" to 1" valves
- 35 to 65 in-lbs torque
- Tough aluminum gear box with metal gears
- Actuator housing available with "indicator flag" or with "blank" lid
- Waterproof connector plugs
- Mountable at any angle
- 110V operation with AC adaptor
- Private labeling available
- Customization available for your specific application!
|
|
For quarter-turn applications the IQT is designed for direct drive, and can be mounted at any operating angle. The rugged construction is double-sealed to prevent water and dust ingress even during site wiring.
Torque range 50 to 2,000 Nm (36 to 1,475 lbf-ft).
•Available for three-phase, single-phase or DC supplies.
•Variable output speed.
•Multiport controller option.
•Secure self-locking output for butterfly valves and dampers without the use of additional brakes.
|
|
|
|
Valve actuators
