|
|
EE66 Series
Air Velocity Transmitter for measurement down to "0" m/s
EE66 air velocity transmitter series are designed for high accuracy measurement of lowest air velocities. It is the ideal solution for laminar flow control and special ventilation applications. The E+E thin film sensor is operating on an innovative hot film anemometer principle. This guarantees excellent accuracy for air velocity down to almost 0 m/s, which is not possible for conventional anemometers with commercial temperature sensors or NTC bead thermistors
EE66 series are available with current or voltage output, the measuring range and the response time can be selected with jumpers by the user.
Measuring range: 0...1 m/s; 0...1.5m/s; 0...2m/s (adjustable by jumpers)
Response time: typ. 4s or typ. 0.2s (adjustable by jumpers)
Outputs: 0...10 V or 4...20 mA (adjustable by jumpers)
Supply: 24V AC/DC
|
|
The Model 4046 primary calibrator has a range of 2.5 to 300 liters per minute (lpm). This small, portable, battery-operated unit is lightweight and easy to use. Volumetric flowrate is displayed continuously so adjustments to pump flow can be made in real-time. This primary calibrator is accurate to 2% of reading.
Features and Benefits:
- Provides continuous real-time volumetric flow rate readings, so pump adjustment and calibration is fast and easy
- Battery powered, compact and lightweight
-Field portable—use the same primary calibrator for adjustment, calibration and periodic checks
- Comes with a NIST traceable calibration certificate
- Kits come complete and are ready to use
Applications:
- Environmental sampling
- Indoor air quality
- Industrial hygiene sampling
- Epidemiology health studies
- Field services
|
|
| ... products without technical information |
| |
FLUXUS® G709 is an ultrasonic flowmeter for permanent installation in 19" rack systems.
In addition to the flow channels, FLUXUS® G709 can be equipped with up to 4 process inputs. With its wide range of electrical inputs and outputs, it can handle and process a great variety of process parameters.
The integrated flow calculator can perform a standard volume flow or mass flow correction according to ISO 12213-1. The connection of external process pressure and temperature measurements is needed for the calculation.
An extended status display helps the user to judge the measuring situation and current measuring precision directly during the measurement.
|
|
Minisonic G is an accurate and economical instrument for the instantaneous actual flowrate measurement of gas. The flowmeter accepts the PTZ corrector to obtain the normal flowrate. This ultrasonic instrument resolves all industrial needs.
In standard they offer :
• A display of flow and volume, of the direction and gas velocity,
• One 4-20mA output, 2 relays, 1 serial link, 1 software for PC.
It includes a very lastest electronic technology combined with highly digital signal porcessing technics and with more resources such as :
• echo analyser with automatic control (ESC mode : 'auto-focus' for the ultrasonic signals)
• zero offset adjustment for a reliable results
• high resolution time measurement < 0.1 ns
• an enhanced emission power
• a better noise rejection
• ergonomic keypad and menu calibration backlighted display
• possible to set a second 4-20 mA output
|
|
|
|
|
|
Portable ultrasonic flowmeter FLUXUS F601 is ideal for troubleshooting, plant optimisation and for control of permanent meters.
Features
* Wide application range thanks to the ability of the transmitter to work with shear wave AND lamb wave transducers at all frequencies
* A single pair of shear wave transducers fits a wide pipe diameter range
* Rapid installation without process interruption
* Bi-directional measurement
* High measurement dynamics
The FLUXUS ® G ultrasonic flowmeters use the proven "clamp-on" technology. The flow transducers are simply clamped onto the outside of the pipe. The measurement can hence be put into operation without cutting into the pipe and without production stop. The installation costs are low, retrofitting is not a problem.
Since the transducers are not in contact with the gas, there is no possibility of chemical attack. There are no moving mechanical or pressure loaded parts and thus no wear an tear. FLUXUS G is ideal for measurements at high pressures or on lines with pressure peaks.
Two transducer types for a uniquely wide application range
All FLUXUS® G transmitters support both lamb wave and shear wave transducers at all transducer frequencies. In this way the measuring system can be optimized to even the most demanding applications.
The Lamb wave transducers are ideal for measurement at high flow velocities, in natural gas pipelines for example, or at low pressures, amongst others in compressed air circuits. The shear wave transducers cover a wide range of pipe diameters and wall thicknesses. They are the best choice for mobile measurement or for high pressure systems.
|
|
|
|
|
|
Fluids: Gas, Steam, Liquids
Diameters of pipes/ channels:
0..20 mm deltaflow DF8
15..100mm deltaflow DF10M
65..3000mm deltaflow DF25
500..15000mm deltaflow DF50
Operating conditions:
-250..1240 °C
0..800 bar
Pure to extremely contaminated, aggressive media
Eexia
TRD
The deltaflow flometer is continiously developed and inprooved and we hold several patents on the deltaflow Technology. But we do not only rely on our own know-how %u2013 systec is furthermore co-operating with well known partners sich as the institute for flow mechanics of the University of Erlangen oder the PtB in Braunschweig.
Due to the special probe profile the deltaflow can assure a high level of precision and excellent process viability, even in extreme conditions causing the lowest residual pressure loss. The deltaflow has been installed several thousand times.
Typical Applications are flow measurement of steam, perssurized air, water, liquids, stack gas, flare gas, natural gas.
Typical industries where our deltaflow integrating pitot tubes are used are Power Plants, Chemistry, Petrochemistry, Gas- and Oil Exploration, waste water plants.
The program to size and design the deltaflow is very self-explanatory and you can download it for free from our web-page as a Windows file (Windows 9x, 2000 and NT).
You can find more details in the referring information sheets. At the bottom of this page you can find links to the information sheets and to the software
|
|
Differential pressure instrument PascalMaxx 500/2000 Z
- Easy startup
- High precision silicon membrane sensor
- Automatic Zero-Point calibration
- Simple 2-point calibration
- Adjustable analogue outputs (V and mA)
- 1 adjustable switch (230V) for 2 thresholds
- Password protection system
- Large and clear LCDisplay
|
|
Compact Orifice Oriflow
Applications
The Oriflow compact orifice is used for flow measurements of conductive and non-conductive fluids, gases and vapours in all industrial branches. Applications include flow measurements (volume/mass) for balancing (compressed air systems, heat carries, vapours, chemical products, for example), process control and high throughput applications.
Reliability
already over 2,000 units in operation
extremely rugged and stable measuring instrument
suited for extreme applications
Special features
dry calibration is possible
highly reproducible results
easy to install without differential pressure lines
Flexibility
DN 15 to DN1000
0,4 bis 20000 m 3 /h
-40 °C to +400 °C (depending on model)
to PN 40 (higher upon request)
current output with HART®
electronical local display
|
|
|
|
|
|
AALBORG®'s heavy-duty IN-LINE and FLANGED ROTAMETERS are fully enclosed in a seamless brushed stainless steel case. Ideal for applications with flow rates up to 20 GPM and 90 SCFM, these flow meters are used with water and air service. These Model M ROTAMETERS are graduated for direct reading of water and air and come equipped with FNPT end fittings for easy in-line installation. Wetted parts include: borosilicate glass flowtubes, Viton® o-rings, and 316 stainless steel fittings, guide rods, floats and float stops.
SPECIFICATIONS
ACCURACY: ±3% of full scale.
MINIMUM FLOW RATE: Approximately 10% of maximum flow rate.
REPEATABILITY: ±0.5% of full scale.
MAXIMUM PRESSURE AT 200° F 93° C: 200 psig (tube sizes 3, 4, 5 and 6). 250 psig (tube sizes 8 and 9).
MAXIMUM OPERATING TEMPERATURE: 200° F (93° C).
DESIGN FEATURES
. Heavy duty stainless steel.
. Thick polycarbonate safety shields.
. Fluted or plain tapered tubes.
. Direct reading metric or English system scales.
. Unique design facilitates ease of maintenance and cleaning processes.
|
|
|
Kanomax anemometers can measure a wide variety of parameters to test ventilation rate. The parameters include air velocity, airflow, static pressure, temperature, and humidity of the indoor environment.
|
|
|
|
|
|
Specially developed for the supervision of clean-rooms, the CPE 300 is dedicated to measures of low pressure andor depression of air or neutral gases from 0/+10 Pa to -1000 /+1000 Pa.
The CPE 300 presents the advantage to become integrated perfectly into walls and to answer to the standard of cleanliness thanks to its stainless case (brushed or with lacquered).
It is equipped with 2 visual and audible alarms, with 2 reversers relays, of a big electroluminescent display and a process of autocalibration which guarantees in the time an excellent stability and a reliability of the measure in low as in high scale.
Thanks to its digital communication (RS 232 and Protocol Modbus RS 485), it offers the possibility of showing alternately (in addition of the measure of pressure) two other parameters resulting from temperature, humidity, velocity or airflow external sensors (KIMO).
Two innovative systems to facilitate the maintenance on-site :
· Its measuring element benefits from the SMART PRO system. It is individually adjusted and is automatically recognized by the device. Thanks to this process, it is possible to replace the measuring element in a simple and fast way without return of the sensor to the factory.
· The calibration in front face : this system allows to proceed to the calibration of the device without un-mounting it.
The sensor CPE 300 is so always operational !
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
Measuring range : from 0/+10 Pa to -10 000/+10 000 Pa
Configurable intermediary and central zero ranges
Air velocity and airflow functions
Interchangeable measuring sensor (SPI technology)
Simultaneous display of 1 to 4 parameters
External transmitter unputs (KIMO class 200 and 300) and thermocouple K
2 output 4-20 mA or 0-10 V (4 wires), RS 232, 2 RCR relays 6A/230 Vac
2 visual (dual color LED) and audible (buzzer) alarms
Software, keypad or remote control configuration
MODBUS network RS 485 system (optional)
ABS or ALU IP 65 housing, with or without backlit gaphic display
Mounting with the 1/4 turn system with wall-mount plate
CP301 : -100/+100 Pa (resolution : 0.1 Pa)
CP302 : -500/+500 Pa
CP303 : -1000/+1000 mbar
CP304 : -10 000/+10 000 mbar
• Barbed fittings Ø 5,2 mm
• Unit of measurement : Pa, mmH2O, mbar, inWG, mmHG
• Power supply : 24 Vac /Vdc, 115 Vac or 230 Vac
• Outputs : 2 x 4-20 mA or 2 x 0-10 V
• Functions : pressure, air velocity, airflow with Pitot tubes, Debimo and other coefficients, integration of measure, self-calibration, measuring correction factor, temperature compensation : manual or automatic (thermocouple K input).
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
ComfortSense
Thermal comfort measurement according to EN 13182, ISO 7736 and ASHRAE standard 113
Dantec Dynamics’ ComfortSense system is designed for research and development of heating and air conditioning systems requiring multi-point measurements of air velocity and temperature. Draught measurements require omnidirectional sensors with a frequency response of at least 2 Hz, which is fulfilled by the present system.
ComfortSense elements
The ComfortSense system consists of a main frame with anemometer circuits for up to 16 probes. The omnidirectional probes measure both air velocity and temperature. Six frames can be connected so that up to 96 probes can be monitored simultaneously. The ComfortSense main frame has a built-in A/D converter with USB 2.0 interface.
Easy-to-use
It is easy for the user to setup a measurement sequence and make a measurement grid with selection of probes from a user library. The software delivers statistical results based on user-defined measurement cycles. The ruggedly designed probes and cables are perfectly suited for large test rooms.
|
|
The Activa Sensor Array provides fl ow,
temperature and pressure signals in a compact
unit that requires only one hydraulic line break.
Each sensor transmits an output signal that is
easily integrated with PCs, PLCs, recorders or
panel displays. Signals can also be transmitted to
Flo-tech’s F6700/F6750 Series digital displays.
|
|
|
|
|
|
ACCUBALANCE® AIR CAPTURE HOOD
The TSI Model 8375 Accubalance Capture Hood is a multipurpose electronic air balancing instrument for reading air volume flow at diffusers, and grilles. It is ideally suited for commissioning agents, facilities managers, health and safety specialists, test engineers, and test and balance professionals. This ultra light weight, ergonomically designed kit saves time and money while helping to create a healthy and energy efficient environment.
Applications include thermal comfort studies, HVAC testing, adjusting and balancing, as well as air volume measurements.
Features and Benefits
- Ergonomic design and ultra light weight for easy one person operation
- Detachable digital manometer for use in other applications with Pitot, air flow, temperature, velocity matrix, or relative humidity probes
- Back pressure compensated
- Multiple hood sizes available
- Bio-Safety hood kit available
Applications:
- Thermal Comfort
- HVAC testing, adjusting and balancing
- Air volume measurements
|
|
| ... products without technical information |
| |
|
Kanomax anemometers can measure a wide variety of parameters to test ventilation rate. The parameters include air velocity, airflow, static pressure, temperature, and humidity of the indoor environment.
|
|
|
|
|
|
Specially developed for the supervision of clean-rooms, the CPE 300 is dedicated to measures of low pressure andor depression of air or neutral gases from 0/+10 Pa to -1000 /+1000 Pa.
The CPE 300 presents the advantage to become integrated perfectly into walls and to answer to the standard of cleanliness thanks to its stainless case (brushed or with lacquered).
It is equipped with 2 visual and audible alarms, with 2 reversers relays, of a big electroluminescent display and a process of autocalibration which guarantees in the time an excellent stability and a reliability of the measure in low as in high scale.
Thanks to its digital communication (RS 232 and Protocol Modbus RS 485), it offers the possibility of showing alternately (in addition of the measure of pressure) two other parameters resulting from temperature, humidity, velocity or airflow external sensors (KIMO).
Two innovative systems to facilitate the maintenance on-site :
· Its measuring element benefits from the SMART PRO system. It is individually adjusted and is automatically recognized by the device. Thanks to this process, it is possible to replace the measuring element in a simple and fast way without return of the sensor to the factory.
· The calibration in front face : this system allows to proceed to the calibration of the device without un-mounting it.
The sensor CPE 300 is so always operational !
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
Measuring range : from 0/+10 Pa to -10 000/+10 000 Pa
Configurable intermediary and central zero ranges
Air velocity and airflow functions
Interchangeable measuring sensor (SPI technology)
Simultaneous display of 1 to 4 parameters
External transmitter unputs (KIMO class 200 and 300) and thermocouple K
2 output 4-20 mA or 0-10 V (4 wires), RS 232, 2 RCR relays 6A/230 Vac
2 visual (dual color LED) and audible (buzzer) alarms
Software, keypad or remote control configuration
MODBUS network RS 485 system (optional)
ABS or ALU IP 65 housing, with or without backlit gaphic display
Mounting with the 1/4 turn system with wall-mount plate
CP301 : -100/+100 Pa (resolution : 0.1 Pa)
CP302 : -500/+500 Pa
CP303 : -1000/+1000 mbar
CP304 : -10 000/+10 000 mbar
• Barbed fittings Ø 5,2 mm
• Unit of measurement : Pa, mmH2O, mbar, inWG, mmHG
• Power supply : 24 Vac /Vdc, 115 Vac or 230 Vac
• Outputs : 2 x 4-20 mA or 2 x 0-10 V
• Functions : pressure, air velocity, airflow with Pitot tubes, Debimo and other coefficients, integration of measure, self-calibration, measuring correction factor, temperature compensation : manual or automatic (thermocouple K input).
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
ComfortSense
Thermal comfort measurement according to EN 13182, ISO 7736 and ASHRAE standard 113
Dantec Dynamics’ ComfortSense system is designed for research and development of heating and air conditioning systems requiring multi-point measurements of air velocity and temperature. Draught measurements require omnidirectional sensors with a frequency response of at least 2 Hz, which is fulfilled by the present system.
ComfortSense elements
The ComfortSense system consists of a main frame with anemometer circuits for up to 16 probes. The omnidirectional probes measure both air velocity and temperature. Six frames can be connected so that up to 96 probes can be monitored simultaneously. The ComfortSense main frame has a built-in A/D converter with USB 2.0 interface.
Easy-to-use
It is easy for the user to setup a measurement sequence and make a measurement grid with selection of probes from a user library. The software delivers statistical results based on user-defined measurement cycles. The ruggedly designed probes and cables are perfectly suited for large test rooms.
|
|
The Activa Sensor Array provides fl ow,
temperature and pressure signals in a compact
unit that requires only one hydraulic line break.
Each sensor transmits an output signal that is
easily integrated with PCs, PLCs, recorders or
panel displays. Signals can also be transmitted to
Flo-tech’s F6700/F6750 Series digital displays.
|
|
| ... products without technical information |
| |
|
|
|
|
Measuring range : from 0/+10 Pa to -10 000/+10 000 Pa
Configurable intermediary and central zero ranges
Air velocity and airflow functions
Interchangeable measuring sensor (SPI technology)
Simultaneous display of 1 to 4 parameters
External transmitter unputs (KIMO class 200 and 300) and thermocouple K
2 output 4-20 mA or 0-10 V (4 wires), RS 232, 2 RCR relays 6A/230 Vac
2 visual (dual color LED) and audible (buzzer) alarms
Software, keypad or remote control configuration
MODBUS network RS 485 system (optional)
ABS or ALU IP 65 housing, with or without backlit gaphic display
Mounting with the 1/4 turn system with wall-mount plate
CP301 : -100/+100 Pa (resolution : 0.1 Pa)
CP302 : -500/+500 Pa
CP303 : -1000/+1000 mbar
CP304 : -10 000/+10 000 mbar
• Barbed fittings Ø 5,2 mm
• Unit of measurement : Pa, mmH2O, mbar, inWG, mmHG
• Power supply : 24 Vac /Vdc, 115 Vac or 230 Vac
• Outputs : 2 x 4-20 mA or 2 x 0-10 V
• Functions : pressure, air velocity, airflow with Pitot tubes, Debimo and other coefficients, integration of measure, self-calibration, measuring correction factor, temperature compensation : manual or automatic (thermocouple K input).
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
ComfortSense
Thermal comfort measurement according to EN 13182, ISO 7736 and ASHRAE standard 113
Dantec Dynamics’ ComfortSense system is designed for research and development of heating and air conditioning systems requiring multi-point measurements of air velocity and temperature. Draught measurements require omnidirectional sensors with a frequency response of at least 2 Hz, which is fulfilled by the present system.
ComfortSense elements
The ComfortSense system consists of a main frame with anemometer circuits for up to 16 probes. The omnidirectional probes measure both air velocity and temperature. Six frames can be connected so that up to 96 probes can be monitored simultaneously. The ComfortSense main frame has a built-in A/D converter with USB 2.0 interface.
Easy-to-use
It is easy for the user to setup a measurement sequence and make a measurement grid with selection of probes from a user library. The software delivers statistical results based on user-defined measurement cycles. The ruggedly designed probes and cables are perfectly suited for large test rooms.
|
|
The Activa Sensor Array provides fl ow,
temperature and pressure signals in a compact
unit that requires only one hydraulic line break.
Each sensor transmits an output signal that is
easily integrated with PCs, PLCs, recorders or
panel displays. Signals can also be transmitted to
Flo-tech’s F6700/F6750 Series digital displays.
|
|
|
|
|
|
Measuring range : from 0/+10 Pa to -10 000/+10 000 Pa
Configurable intermediary and central zero ranges
Air velocity and airflow functions
Interchangeable measuring sensor (SPI technology)
Simultaneous display of 1 to 4 parameters
External transmitter unputs (KIMO class 200 and 300) and thermocouple K
2 output 4-20 mA or 0-10 V (4 wires), RS 232, 2 RCR relays 6A/230 Vac
2 visual (dual color LED) and audible (buzzer) alarms
Software, keypad or remote control configuration
MODBUS network RS 485 system (optional)
ABS or ALU IP 65 housing, with or without backlit gaphic display
Mounting with the 1/4 turn system with wall-mount plate
CP301 : -100/+100 Pa (resolution : 0.1 Pa)
CP302 : -500/+500 Pa
CP303 : -1000/+1000 mbar
CP304 : -10 000/+10 000 mbar
• Barbed fittings Ø 5,2 mm
• Unit of measurement : Pa, mmH2O, mbar, inWG, mmHG
• Power supply : 24 Vac /Vdc, 115 Vac or 230 Vac
• Outputs : 2 x 4-20 mA or 2 x 0-10 V
• Functions : pressure, air velocity, airflow with Pitot tubes, Debimo and other coefficients, integration of measure, self-calibration, measuring correction factor, temperature compensation : manual or automatic (thermocouple K input).
Join our distribution network all over the word....Contact us !
|
|
|
|
|
|
ComfortSense
Thermal comfort measurement according to EN 13182, ISO 7736 and ASHRAE standard 113
Dantec Dynamics’ ComfortSense system is designed for research and development of heating and air conditioning systems requiring multi-point measurements of air velocity and temperature. Draught measurements require omnidirectional sensors with a frequency response of at least 2 Hz, which is fulfilled by the present system.
ComfortSense elements
The ComfortSense system consists of a main frame with anemometer circuits for up to 16 probes. The omnidirectional probes measure both air velocity and temperature. Six frames can be connected so that up to 96 probes can be monitored simultaneously. The ComfortSense main frame has a built-in A/D converter with USB 2.0 interface.
Easy-to-use
It is easy for the user to setup a measurement sequence and make a measurement grid with selection of probes from a user library. The software delivers statistical results based on user-defined measurement cycles. The ruggedly designed probes and cables are perfectly suited for large test rooms.
|
|
The Activa Sensor Array provides fl ow,
temperature and pressure signals in a compact
unit that requires only one hydraulic line break.
Each sensor transmits an output signal that is
easily integrated with PCs, PLCs, recorders or
panel displays. Signals can also be transmitted to
Flo-tech’s F6700/F6750 Series digital displays.
|
|
|
|
see the results for the following category : 
