|
|
Loc-Line® Acid Resistant Hose is excellent for rinsing cycles in plating operations.
Acid environments won't corrode the Loc-Line® Acid Resistant Hose because of its polyester composition.
CAUTION: Loc-Line® Acid Resistant Hose is not intended for conveying acids or high pressure applications.
Common Compatability with Polyester Products Acid Resistant Loc-Line® Yellow Color
No Acetone Yes Acids, (Less than 150° F)
No Acids, (Greater than 150° F) Yes Alcohols
Yes Aromatic Solvents No Chlorinated Hydrocarbon
No Bases, Strong No Ethyl Acetate
Yes Gasoline Yes Greases
Yes Hydrocarbons Yes Oils
Yes Salt Solutions No Water (Greater than 150° F)
|
|
SpiralAirTM (SA)
High-flow Air Atomizing Spray Nozzles
Design Features
* A two-fluid nozzle using any gas as the atomizing fluid
* Three-stage process that uses atomizing air more efficiently than conventional designs
* Two-phase atomization for highest performance
* Designed for high reliability in extremely hostile environments
* Efficient design reduces compressed air consumption
* Standard and custom lance designs are available for any application
* U.S. Patent #5,240,183
Spray Patterns: Full Cone and Flat Fan
Spray Angles: 20° to 90° (Other angles available by special order)
Flow rates: 0.33 to 26 gpm (2.0 to 80 L/min)
|
|
Air nozzles, flat jet
16 orifices. Uniform layer of air. Limited noise. Flow rate range: 9 - 33 cfm @ 15 - 75 psi. Material: polyacetal resin.
Typical applications: blow off, cooling, drying cleaning.
|
|
According to occupational health and safety standards (in Germany), a sound level of 85dB(A) may only be exceeded in case of justifiable exceptions. Excessive noise presents a health hazard to workers as well as impairing communication and performance. Elring multi-channel nozzles serve to achieve a major reduction in sound levels.
Enhanded Effectiveness Using Pinpointed Blowing Power
Aerodynamically adapted air supply to the nozzle channels increases effectiveness, while the laminar air flow of Elring multi-channel nozzles also produces a strong effect beyond the delivery end of the nozzles. This results in a further efficiency increase as well as allowing conveyance of heavier production parts.
Benefits
- cost savings in work environments requiring noise protection
- cost savings through reduced consumption of compressed air
- enhanced performance through optimized compressed air delivery at the nozzles
- pinpointed blowing action through adjustable compressed air nozzles
|
|
TYPICAL APPLICATIONS
Asphalt or tar laying, bottle washing, coal and gravel washing, degreasing, dishwashing, foam control, industrial washers, metal
cleaning-rinsing and washing, spray coating, vehicle washing, water misting and water fountains.
|
|
These units are purposely designed items for use in paint spraying and coating applications. Additional special
purpose air assisted tips are also shown for reference.
|
|
OUR RANGE INCLUDES
FULL CONE PATTERN:
Full cone flange connection / full cone vaneless - off line / full cone three piece nozzles / full cone square spray / square spray - large flow / full cone injector nozzles / full cone off line spray / full cone nozzle tips / multiple full cone - standard spray angles / multiple full cone wide spray angle / full cone spiral nozzles / full cone spiral - extra wide angle.
FLAT JET PATTERN:
Flat jet high pressure washing nozzles / flat jet standard flow rates / flat jet large flow rates, flat jet low flow rates / flat jet tips - standard flow / flat jet tips / large flow / dove-tail tips - standard flow / dovetail tips - large flow / flat jet - large spray angles / flat jet - high impact (spoon nozzles). Also pencil jets.
HOLLOW CONE PATTERN:
Hollow cone - wide spray angle / hollow cone moulded plastic nozzles / hollow cone large flow rates / hollow cone - in line spray / hollow cone deflected spray / hollow cone - low pressure nozzles.
|
|
Ultrasonic Nozzle
Full cone air-atomizing type. Very small drops (smaller than those from any other type of air-atomizing nozzle). High noise level. Uses supersonic air pressure waves to create small drops. Flow rate range: 0.3 - 46 gph.
Spray angle: 15º.
Materials: 303 stainless steel (head), 303 stainless steel and brass (body).
Typical applications: humidification.
|
|
MicroWhirlTM (MW)
Atomizing Spray Nozzles, Misting Nozzles, Fog Nozzles
Design Features
* Outstanding atomization
* Rugged pinless design
* Drip-free performance
* 70 micron polypropylene filter
* Safety wire hole available
* U.S. Patent #7198201
* Minimum operating pressure 100 psi (7 bar)
Spray Characteristics
* Mist at low pressure; fog at high pressure
Spray pattern: Cone-shaped Fog
Flow rates: 0.009 to 0.151 gpm (0.032 to 0.517 L/min)
|
|
Ultrasonic Oscillators offer a new method of atomization. Electric waves are transformed into mechanical oscillations. Within the atomizer, these oscillations cause a regulated thin film of liquid to experience a minute wave action. These oscillations act to shear the liquid into finely atomized droplets.
Generally, Lechler ultrasonic atomizers are suited to atomize liquids that are free of solids and have a viscosity no higher than 50 centipoises.
Typical applications are:
. Air humidifying
. Product moistening
. Injecting gas into liquids and degassing liquidsn
. Adding liquids during stirring and mixing operations
. Medical technology
|
|
Spraying Systems Co. offers tens of thousands of products, along with an abundance of technical information and problem-solving ideas to help you optimize your spray application. From spray nozzle basics to automated spray systems, it is highly likely that you'll find the products you need. And, in many instances you'll find more than one product that is suitable for your application. If you're not sure which product is best for you, just give us a call, in the U.S. at 1-800-95-SPRAY (outside the U.S. call -630-665-5000) or visit our Web site at www.spray.com. We have hundreds of technical experts that can help you determine which of our over 80,000 nozzles will yield the performance you require.
|
|
Our UniJet spray nozzles allow for quick and easy spray tip replacement. Spray tips can be removed by simply unscrewing the existing retainer cap, removing the existing spray tip by hand and installing the new tip. There's no need to replace the nozzle body.
Some UniJet nozzles are designed for use with compressed air for blow-off and drying applications. TK spray tips feature a round orifice and a large, unobstructed air volume passage with a wide angle, medium-velocity spray. UniJet blow-off nozzle assemblies feature a horizontal slot across the tip of the nozzle and delivers a uniform flat fan pattern.
UniJet spray nozzles are available with a large choice of interchangeable spray tips, body types, sizes, spray angles and spray patterns. Material options include brass, 303 stainless steel and hardened stainless steel. A wide variety of accessories is available. Choose from strainers, check valves, jet stabilizers, adapters, plates, fittings, mounting and cap options and more.
|
|
SC
Cast Metal Alloy, Full Cone Nozzles
Design Features
* Complete line of full cone nozzles made in cast metal alloys
* Internal removable vane
* Male and female connections
* Flanged connections available
* For plastic nozzles, see NC or MaxiPass nozzles
Spray Characteristics Spray pattern: Full Cone with uniform distribution
Spray angles: 60°, 90° and 120°
Flow rates: 1.68 to 2150 gpm (6.25 to 8180 L/min)
|
|
Spin spray applications produces a sharpl edge and is scarcely visible on the substrate. Spray nozzles can dispense less glue on large areas. The size of the applicated glue depends on the hot air pressure.
Offered nozzels are:
* Braas nozzles with 7 or 12 air orifices left or right twisting, some have special wide air orifices from 0,3 to 2mm
* Brass nozzle plates from 0,3 to 1,25mm
* Stainless steel nozzles with 7 or 12 air orifices left or right twisting, some have special wide air orifices from 0,25 bis 1mm
|
|
|
Ultrasonic Oscillators offer a new method of atomization. Electric waves are transformed into mechanical oscillations. Within the atomizer, these oscillations cause a regulated thin film of liquid to experience a minute wave action. These oscillations act to shear the liquid into finely atomized droplets
|
|
SPRAY & SPYRO NOZZLES
They are particularly indicated for depositing glue on a wide space with a minimum thickness. The Spray version nozzle is used for an even spraying of the product, while the Spyro series allows you to obtain spiral-shaped glue strips. Different diameters and air cap shapes give the customer the perfect solution to all gluing problems.
|
|
TYPICAL APPLICATIONS
Asphalt or tar laying, bottle washing, coal and gravel washing, degreasing, dishwashing, foam control, industrial washers, metal
cleaning-rinsing and washing, spray coating, vehicle washing, water misting and water fountains.
|
|
|
The design of the tubes of Drying by Atomization DELAVAN, refers of it in the field of the Manufacture of Powder. We to you propose a complete range of Haute-Pression tubes (SDX) and Bi-Fluids (Swirl-Air)
|
|
In any dryer good mixing and efficient liquid-gas contact are of basic importance to assure rapid drying. The height of the dryer system is largely determined by the time required to dry the largest particle produced by the atomizer, while other important parameters are represented by the inlet-air temperature and the properties of the product being processed.
Spray drying has several advantages, the main one being the ability to handle heat-sensitive products such as food and pharmaceuticals. This is due to the fact that the drying process of a drop happens by loosing water on the external layers, and this keeps the inside material in the drop cool or at least protected against excessive heat.
|
|
TW
Tank Washing Nozzles, Clog Resistant Nozzles
Design Features
* Clog-resistant spiral design
* Energy efficient; uses less water than conventional designs
* Compact design; fits small openings
Spray Characteristics
* Easy to maintain
* Unique patterns that spray in opposing directions
* See LEM for other tank-washing applications
Flow rates: 3.0 to 163 gpm (11.4 to 260 L/min)
|
|
Twist & DryTM (TD)
Spray Drying, Hollow Cone Nozzles
Design Features
* Patented locking mechanism for quick and easy change-out and maintenance
* Choose TD-K to operate at high pressures for greater yield capacity
* PEEK backup ring with Viton® 90 or Silicone O-rings (for higher temperatures)
* Female-threaded or butt weld pipe connections
* Easy assembly, no special tools required
* Orifice size: 0.034" through 0.157" (0.864 mm through 3.99 mm)
* Interchangeable swirl and orifice discs for variable patterns and flow rates
* More information on the TD-K nozzle
Spray Characteristics:
Spray pattern: Hollow Cone
Spray angles: 50°, 55°, 60°, 65°, 70°, 75° and 80°
Flow rates: 8.94 to 1570 gph (35.3 to 5970 L/h)
|
|
SPRAY CHARACTERISTICS:
F-Series spray nozzles produce a flat, fan-shaped spray pattern, with spray angles available from 0° solid stream to 110° fans measured at 40 psi. Spray angles generally increase with pressure.
TYPICAL APPLICATIONS:
Suitable for a variety of washing and spraying applications.
- Parts Cleaning
- Metal Washing
- Foam Control
- Asphalt Spraying
- Gravel Washing
- Vehicle Washing
- Fertilizer Spraying
- Dishwashers
|
|
Design Features
* Multiple flat fan patterns/li>
* Solid one-piece construction
* Female connection
Spray Characteristics
* Relatively small droplets
Spray pattern: Dense Full Cone
Spray angles:
SS4.8 through SS25 - 35°
SS35 through SS70 - 45°
Flow rates: 2.40 to 157 gpm (9.16 to 618 L/min)
|
|
SPRAY CHARACTERISTICS:
0° F-Series spray nozzles produce a high impact sold stream. Used in situations where maximum impact is required over a very small target area.
TYPICAL APPLICATIONS:
- Metal Washing
- Agitation
- Mixing
|
|
|
Recent enhancements make our SprayDry nozzle better than ever. New features allow more user configurability, reduced maintenance time, improved wear resistance and more.
|
|
TYPICAL APPLICATIONS
Chemical processing, continuous casting, cooling castings and moulds, curing concrete products, evaporative coolers, foam control,
incineration, quenching, spray coating, spray drying, flue gas desulfurisation.
|
|
TYPICAL APPLICATIONS
Aerating water, brine sprays, chemical processing, coil defrosting, dust control, evaporative condensers, evaporative coolers, industrial
washers, roof cooling, spray ponds, spray coating, gas scrubbing and washing, humidification, gas cooling, cooling towers, coal washing,
degreasing, gravel washing, dishwashing, foam control, industrial washing and water fountains.
|
|
Aerating water, brine sprays, chemical processing, coil defrosting, dust control, evaporative condensers, evaporative coolers, industrial
washers, roof cooling, spray coating, gas scrubbing and washing, cooling towers, coal washing, degreasing, gravel washing, dishwashing,
foam control, industrial washing and water fountains.
|
|
TYPICAL APPLICATIONS
Aerating water, brine sprays, chemical processing, coil defrosting, dust control, evaporative condensers, evaporative coolers, industrial
washers, roof cooling, spray ponds, spray coating, gas scrubbing and washing, humidification, gas cooling, cooling towers, coal washing,
degreasing, gravel washing, dishwashing, foam control, industrial washing and water fountains.
|
|
Various types of fixed and rotating spray heads are specified in this section and are designed to suit a wide range of
applications and installations.
|
|
|
|
