Probes

Insertion length: 203.2 mm - 1,219.2 mm

... The GENIE 750 is a fixed probe with membrane for gas sampling. It is installed on a full-opening valve, and its insertion length ranges from 20 cm to 1.2 meters. Technical Specifications Maximum operating pressure 258.6 barg (3750 psig) Maximum ...

The ES-2 Electrical Conductivity and Temperature Sensor is designed to measure the electrical conductivity of water in a pipe or tank. When you pair the new ES- 2 with a TEROS 12 soil moisture sensor in the soil, you'll begin to develop a complete picture ...

... • High sensitivity gamma measurement • 2" x 2" NaI(Tl) • Belongs to CSP family • Calibration via PC • Dynamic energy discriminator button • Telescopic pole with H*(10) ambient gamma dose equivalent rate measurement probe • Gamma dose rate measurement ...

... DESCRIPTION Based on the ZrO2 C3M Electrolyte, the CarboProbe HT probe can handle temperatures up to 1700°C. All parts exposed to high temperatures are ceramic or platinum. This probe has a robust construction with a 15 mm diameter ceramic tube that ...

... Constant results even when hot The eddy current method can be used without compromise even under extreme conditions: material speeds up to 150 m/s and wire temperatures up to 1,200 °C prove no problem for DEFECTOTHERM sensors. The special thermal coils ...

Measuring range: 5 °C - 60 °C

... How energy efficiency is improved Effective protection from moisture damage and excessive cooling Areas of use Protects against dew formation on chilled ceilings. Controls a regulating unit via a holding relay that interrupts the cooling water flow ...

... Optimum accessories for the photometric quantities to be measured Instrument Systems offers a series of EOPs for measuring irradiance and universal radiation coupling. These differ mainly in terms of light throughput, degree of cosine correction and ...

... Mounted on workpiece surface or machine table, LED lamp illuminates immediately when the cutting edge touches the sensor plate and the position is detected. For conductive materials BASE MASTER For all materials BASE MASTER GOLD BASE MASTER MICRO ...

... Real Tech’s Ammonium Probe provides rapid real-time in-situ measurement of ammonium in water or wastewater. The sensor uses ion selective electrode (ISE) measurement technology to monitor ammonium continuously. The integrated automatic temperature compensation ...

... NEW! Second generation Hach LDO sensor technology. Since 2002, Hach has established itself as the premier provider of luminescent dissolved oxygen (LDO) technology, and only Hydrolab Series 5 sondes feature Hach LDO technology – designed, manufactured, ...

... Improve Operational Efficiency with Continuous Data With an easily scalable solution, the 2020 XT allows for the connection of up to 20 sensors. This modular plug-and-play system allows you to monitor the water quality in your wastewater system continuously ...

Contacting Conductivity Sensors measure conductivity of a solution via electrodes. They are ideal for use in cooling towers and boilers, reverse osmosis equipment, and other non-oily applications. A variety of cell constants are available to handle a ...

The FISCHER offers a comprehensive range of around 100 probes, designed to satisfy the requirements of an extremely broad application range. These units are designed to be very robust and highly resistant to wear and offer accurate measuring over an extended ...

... MFI magnetic field indicator – SAMFI Octagonal probe for checking the orientation of magnetic fields, quality of dry and wet magnetic powders and magnetization. Complying with standard ASME-ASTM-MIL-AMS. ...

The WS1806 online five-parameter monitor is a general-purpose controller, which can be connected to smart electrodes and multi-parameter electrodes and display the measured values and electrode status in real time. Compared with similar ones, this product ...

The AmpFlex® is an AC current sensor composed of a flexible Rogowski coil and an electronic module. The sensor permits measurements on conductors where standard clamp-on probes cannot be used. In particular, it can be installed in tight spaces, around ...

... Pocket sensors combine a simple-to-use menu system and intuitive user-interface, providing the ideal solution for quick and easy in-situ testing: Automatic standard recognition for straightforward calibration Automatic temperature compensation ...

... Unheated probe with outlet filter for indoor installation. The filter element can easily be removed by turning the handle 90°. For dust loads up to 2g/m³, non-condensable gases. The probe has no innate ignition source and is therefore ...

... Professional bromine probes Introduction Sealed-cell bromine sensor, 4-20 mA output and automatic temperature compensation with guaranteed accuracy and short response time, thanks to active amperometric measurement. This probe is suitable for process ...

SUP-PTU200 Suspended Solids Meter based on the infrared absorption scattered light method and combined with the application of ISO7027 method, can guarantee the continuous and accurate detection of suspended solids and sludge concentration. Based on ISO7027, ...

... The PhAT probe represents the in situ approach to Raman solids sampling. Solids sampling by Raman is prone to under-sampling. This problem is solved using the PhAT approach, which provides reproducible, representative, focus-free, quantitative Raman measurements. Traditional ...

... Cail & Fletcher Hydrotrac probe is a microwave probe which provides a direct reading of both Brix and temperature. It brings a range of functionalities more extensive than the Cail & Fletcher Monotrac probe. Ultimate performance for any type of application Cail ...

... We work closely with nuclear, automotive and energy industries and many other international companies. We make use of non-destructive testing to expand our product range to guarantee you a clear vision in all conditions. Guide tubes were conducted ...

Insertion length: 300 mm - 1,800 mm

... General information
ZIROX flue gas probes SS31/SS31H are robust oxygen sensors for lambda determination in large-scale combustion plants and for measuring the oxygen partial pressure in furnace atmospheres. The probes are calibration-, drift- ...

... During manual high-voltage testing, the test pistol is used to contact the test object. Various versions and cable lengths are available for a wide variety of applications. • Safety test pistols up to 10 KV and 12 KV • Safety test pistols with integrated ...