Probes

... Completely field serviceable, the WDG Insitu is a direct-sensing oxygen (O2) probe suitable for applications where the flue gas temperature does not exceed 800oC (1472oF). With a range of different probe lengths offered, its unique inner/outer probe ...

Probes, coupled with a spectrometer, measure reflection, and fluorescence in solids, liquids, powders.

... The Conducell 4UxF is capable of measuring a broad range of conductivity (from 1 to 500’000 µS/cm (Analog) and 1 to 300'000 µS/cm (Arc)), making it suitable for both low and high conductivity measurements.   All wetted parts (DIN 1.4435, PEEK, EPDM) ...

... Radiometric probe for outdoor use for measuring IRRADIANCE in the UVA spectral range (315…400 nm). Supplied with Calibration Report. On request CPM12AA4… cables with 4-pole M12 connector. The LPUVA02 radiometer measures the broadband UVA irradiance ...

... Applications Water Technology Water Quality Monitoring Systems Process Monitoring Process Control Features cost-efficient measurement of process parameters display for measuring values and clear calibration instructions simultaneous temperature measurement 2 ...

... 24cm long probe with moulded handle 6mm diameter shaft ...

The TEGAM MCP-M2 miniature coaxial Kelvin probes come with a spring-loaded center pin for voltage detection, while the outer pin provides the reference current. The lead length is 2m (6.6′) and is terminated with an M12 connector. This probe comes with ...

... * Build in temperature sensor, ATC ( auto temperature compensation ). * 1.413 standard solution are standard accessories. * 4-wire installation. * Linear current output (4.00 - 20.00 mA) * Easy installation and connection. * Conductivity range 1 ...

... Product Details

• Underground bushing probe for Radio Voltstik.

• Model Number: 7-124
• Subtitle: Underground Bushing Probe
• Compatible with: Radio Linked Voltstik

Measuring range: -80 °C - 20 °C

... Dew point sensor FA 500 from -80 to 20°Ctd FA 500 is the ideal dew point sensor with integrated display and alarm relay for refrigeration, membrane and desiccant driers. Special features: -NEW: Modbus-RTU interface -NEW: Higher resolution ...

... DIFFERENTIAL PROBE P9000 Easily Connect to Hioki Memory HiCorders and HiLoggers for High Voltage Testing Overview • - Compact probe for CAT III 1000V environments • - Wave mode: Observe instantaneous waveforms • - RMS mode: Observe RMS value ...

... ATR tunnel cells provide a high degree of analytical accuracy. They are ideal for the chemical analysis of liquids in the IR range. ...

The PHT transmitter converts the high impedance voltage output of pH or REDOX (ORP) probes into standard current or voltage signal that can be safely sent over longer distances. The transmitter provides the necessary for the normal pH/ORP probe’s operation ...

Type 50GI is a sound intensity probe for direct connection to signal analyzers or data acqusition devices with IEPE inputs. The probe includes a pair of phase-matched prepolarized precision microphones which meet the requirements in IEC standard 61043 ...

... X1 Oscilloscope Probe Body. Cable type : Coaxial. Color : Black / yellow. Standard length : 120 cm (47 ''). Detail : Attenuation X1. Input impedance 45 pF. Bandwidth 25 MHz. Rise time 14 ns. ...

... Our 2-Electrode Resistivity Transmitters work best with these applications: Reverse Osmosis Systems Boiler Feed Water Pharmaceutical Water Deionization Systems Return Condensate Semiconductor Water Desalination Systems Our ...

... Measuring Item ORP Field of Use Sewerage Compact and robust aluminum case, simple operation on-site ORP meter. Automate standard solution check. Automatically determines the quality of electrode characteristics. The transmission output range can be ...

... AD1020 Professional Multi-Parameter pH-ORP-ISE-TEMP Bench Meter with RS232/USB interface & GLP AD1020 is a professional bench meter for pH, ORP (Oxidation Reduction Potential), ISE and temperature measurements. Relative mV readings are also provided. Up ...

... Used to locate buried plastic Water Pipes, Gas Pipes and any other non-magnetic utility, Sondes are self-contained transmitters that are used with our cable and pipe locators. Sondes are typically attached to a Flexrod, pushed along the pipe, and the ...

The Sentry custom-engineered steam and water analysis systems (SWAS) meet the most demanding and unique customer requirements for leading energy companies worldwide. Our sample panel systems provide the real-time data and critical insights needed to control ...

... An advanced Langmuir probe for plasma diagnostics Routine monitoring of the I-V plasma characteristic by the Hiden ESPion probe gives direct information relating to plasma stability and reproducibility. Automatic real-time extrapolation of plasma parameters ...

Insertion length: 203.2 mm - 1,219.2 mm

... The GENIE 750 is a fixed probe with membrane for gas sampling. It is installed on a full-opening valve, and its insertion length ranges from 20 cm to 1.2 meters. Technical Specifications Maximum operating pressure 258.6 barg (3750 psig) Maximum ...

The ES-2 Electrical Conductivity and Temperature Sensor is designed to measure the electrical conductivity of water in a pipe or tank. When you pair the new ES- 2 with a TEROS 12 soil moisture sensor in the soil, you'll begin to develop a complete picture ...

... • High sensitivity gamma measurement • 2" x 2" NaI(Tl) • Belongs to CSP family • Calibration via PC • Dynamic energy discriminator button • Telescopic pole with H*(10) ambient gamma dose equivalent rate measurement probe • Gamma dose rate measurement ...

... DESCRIPTION Based on the ZrO2 C3M Electrolyte, the CarboProbe HT probe can handle temperatures up to 1700°C. All parts exposed to high temperatures are ceramic or platinum. This probe has a robust construction with a 15 mm diameter ceramic tube that ...

Measuring range: 5 °C - 60 °C

... How energy efficiency is improved Effective protection from moisture damage and excessive cooling Areas of use Protects against dew formation on chilled ceilings. Controls a regulating unit via a holding relay that interrupts the cooling water flow ...

... Optimum accessories for the photometric quantities to be measured Instrument Systems offers a series of EOPs for measuring irradiance and universal radiation coupling. These differ mainly in terms of light throughput, degree of cosine correction and ...

... Mounted on workpiece surface or machine table, LED lamp illuminates immediately when the cutting edge touches the sensor plate and the position is detected. For conductive materials BASE MASTER For all materials BASE MASTER GOLD BASE MASTER MICRO ...

... Real Tech’s Ammonium Probe provides rapid real-time in-situ measurement of ammonium in water or wastewater. The sensor uses ion selective electrode (ISE) measurement technology to monitor ammonium continuously. The integrated automatic temperature compensation ...

... NEW! Second generation Hach LDO sensor technology. Since 2002, Hach has established itself as the premier provider of luminescent dissolved oxygen (LDO) technology, and only Hydrolab Series 5 sondes feature Hach LDO technology – designed, manufactured, ...

... Improve Operational Efficiency with Continuous Data With an easily scalable solution, the 2020 XT allows for the connection of up to 20 sensors. This modular plug-and-play system allows you to monitor the water quality in your wastewater system continuously ...

Contacting Conductivity Sensors measure conductivity of a solution via electrodes. They are ideal for use in cooling towers and boilers, reverse osmosis equipment, and other non-oily applications. A variety of cell constants are available to handle a ...

The FISCHER offers a comprehensive range of around 100 probes, designed to satisfy the requirements of an extremely broad application range. These units are designed to be very robust and highly resistant to wear and offer accurate measuring over an extended ...

... MFI magnetic field indicator – SAMFI Octagonal probe for checking the orientation of magnetic fields, quality of dry and wet magnetic powders and magnetization. Complying with standard ASME-ASTM-MIL-AMS. ...

The WS1806 online five-parameter monitor is a general-purpose controller, which can be connected to smart electrodes and multi-parameter electrodes and display the measured values and electrode status in real time. Compared with similar ones, this product ...

The AmpFlex® is an AC current sensor composed of a flexible Rogowski coil and an electronic module. The sensor permits measurements on conductors where standard clamp-on probes cannot be used. In particular, it can be installed in tight spaces, around ...

... Pocket sensors combine a simple-to-use menu system and intuitive user-interface, providing the ideal solution for quick and easy in-situ testing: Automatic standard recognition for straightforward calibration Automatic temperature compensation ...

... Unheated probe with outlet filter for indoor installation. The filter element can easily be removed by turning the handle 90°. For dust loads up to 2g/m³, non-condensable gases. The probe has no innate ignition source and is therefore ...

SUP-PTU200 Suspended Solids Meter based on the infrared absorption scattered light method and combined with the application of ISO7027 method, can guarantee the continuous and accurate detection of suspended solids and sludge concentration. Based on ISO7027, ...

... The PhAT probe represents the in situ approach to Raman solids sampling. Solids sampling by Raman is prone to under-sampling. This problem is solved using the PhAT approach, which provides reproducible, representative, focus-free, quantitative Raman measurements. Traditional ...