Probes

CO2 probe for class 320 transmitters Main applications: CO2 monitoring (IAQ) in VAC systems of office buildings, commercial buildings, education facilities. Plastic body, Ø 29.5 mm, length: 175 mm. - Technical Data sheet - ...

Thermocouple temperature probes with sensitive element as per IEC 584-1, 2 and 3 standard

Kimo's gas leak probe is used for all kind of boilers. It detects hydrocarbon and CH4 gas leaks.

The HV-44A is a self-contained instrument that measures high DC voltages up to +40KV. This probe is typically used to measure high voltages in TV sets, power supplies, laboratories and for general high voltage commercial applications.

Accucarb ZCC probe with zirconium oxide The ZCC probe is a high-accuracy oxygen probe, with zirconium oxide, designed for the heat treatment industry. Introduced directly into the oven, at the same working temperature, it performs ...

Separate electronics for harsh environmental conditions: In-situ zirconium oxide probe for direct and continuous measurement of the percentage of residual oxygen in the combustion fumes, in harsh environmental conditions where high ...

Separate electronics for critical process conditions: Extractive zirconium oxide probe for direct and continuous measurement of the percentage of residual oxygen in the combustion fumes in critical process conditions. Equipped with ...

The InPro6860i is an optical dissolved oxygen sensor which offers highly accurate oxygen measurements with enhanced stability, suitable for biopharma applications. Immediate Sensor Availability Calibration data are stored in the sensor. ...

Accurate Measurement of Water Purity. The InPro 7000-VP is a 2-electrode conductivity sensor designed for high accuracy measurement in very low to medium conductivity water. Meets Chemical Industry Needs This sensor is available ...

The InPro 7108-VP-PEEK utilizes 4-electrode technology to expand its measurement range in medium to high conductivity solutions. Wide Measuring Range WideRange technology makes the sensor suitable for many applications; rinsing, control ...

• Ideal for honeycomb composite skin-to-core disbonds. • High sensitivity and crisp signal and response. • Detects near side and far side defects in most applications. • Compatible with pitch-catch RF, IMPULSE or SWEPT methods. • ...

• Ideal for honeycomb composite skin-to-core disbonds. • Works well to detect disbonds in crushed core conditions. • Sensitive to smaller defects. • Allows for easy identification of repaired (potted) areas over disbonds. • Suitable ...

• Ideal for detection of skin-to-skin disbonds (metal-to-metal) • Ideal for detection of delamination in composite • Phase analysis allows evaluation of defect location or part thickness • Detects corrosion between layers • Easily ...

The TB4042 conductivity cell expands the advancements in process conductivity measurement initiated by ABB with four-electrode conductivity measurement. Unlike four-electrode sensors, toroidal sensors have no electrodes. The TB4042 toroidal ...

The TB451 conductivity cell has an integral Tri-Clamp fitting and is designed for use in sanitary applications. ABB offers two styles of these sensors. The first is a flush-face style that meets the process at the Tri-Clamp fitting. The ...

The TB457 conductivity cell has a 316 stainless steel body and integral Tri-Clamp fittings and is designed for use in sanitary applications. The electrode tips and electrodes are sealed with Food and Drug Administration (FDA) approved ...

New features and functions – a major step for the DULCOMARIN®. A gigantic step for your pool system. The measuring and control system DULCOMARIN® 3 is a reliable system for the treatment of swimming pool water. The intuitive menu guidance ...

Water parameter analysis made easy – with the DULCOMETER® diaLog DACb The controller DULCOMETER® diaLog DACb is our compact all-rounder for water analysis. With its specially designed functionalities, e.g. processing or interference ...

Conductivity sensors for optimum process integration: DULCOTEST® sensors meet a wide range of measuring requirements and allow the best solution to any given measuring task to be achieved. Online measurement of electrolytic conductivity ...

The TOP 200 has been completely redesigned and is currently based on Pritchard style optics with an integrated alignment camera. Typical uses for the TOP 200 telescopic optical probe include testing of displays and panel graphics. Unlike ...

LED 25 optical probe is based on a 25mm inner diameter integrating sphere and 1cm² measurement port. It was conceived as a modular system and can be used with distance spacers for “Averaged LED Intensity” measurements compliant with the ...

Instrument Systems provides a range of optical probes for measuring irradiance and illuminance, and also for general coupling of light into the spectrometer. These probes differ in the degree o f light throughout, the spectral range and ...

This is a four-pole graphite conductivity smart sensor using RS485 communication interface and Modbus RTU standard protocol. Corrosion-resistant shell, built-in PT1000 temperature sensor and compensation algorithm, suitable for various ...

This is a fluorescent dissolved oxygen intelligent sensor using RS485 communication interface and Modbus RTU standard protocol. Corrosion-resistant shell, with atmospheric pressure, salinity, temperature compensation calculation.

This is the ammonia nitrogen sensor with RS485 communication interface and Modbus RTU standard protocol. It has built-in PT1000 temperature sensor and compensation algorithm and can replace the membranous head, no reagent, no secondary ...

Conductivity measuring cell made of stainless steel with cell constant c = 0.1 cm-1, with integrated Pt1000 temperature sensor and fixed cable (1.2 m) for connecting to an 856 Conductivity Module. This sensor is suitable for measurements ...

JUMO digiLine Ci now enables inductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to ...

The conductivity sensor has 4 electrodes made of robust special graphite and is characterized by a wide measuring range. It is therefore predestined for determining the conductivity of high salt concentrations. This is why it can be used ...

JUMO digiLine Ci now enables inductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. In addition to the JUMO digiLine interface, system integration can now also take place via an IO-Link ...

Description - Dissolved oxygen probe - Membrane-covered polarographic Clark probe - PVC body more rugged in use - Varied use: in the laboratory, in the field or in industry Dissolved oxygen probes comprise two precious-metal electrodes ...

Conductive conductivity sensor for water, wastewater, process water or pure water • For use with analytical transmitter • Process connection: G1⁄2, G3⁄4, G1, 3⁄4 NPT (male) • 0.05 μS/cm…20 mS/cm; Max. +135°C / +275°F • With two stainless ...

Inductive conductivity sensor for water, wastewater and chemical applications • For use with analytical transmitter • Process connection: G11⁄2 union nut and immersion versions • 1…2000 mS/cm; Max. +100°C / +212°F • Electrodeless ...

Potentiostatic amperometric disinfectant sensor for water and wastewater applications • For use with MAC 100 analytical transmitter • Process connection: PG13.5 • Cl2: 0.03…20 mg/l; ClO2: 0.05…5 mg/l; O3: 0.05…5 mg/l; Max. +70°C / ...

Our GUIDED WAVE™ Single-Sided Transmission (SST) Probe is our most popular fiber optic probe. On the market for over 3 decades, it has been the most widely copied probe design in the industry. Rugged and reliable, it’s ideal for continuous ...

For a complete laboratory measurement solution, our GUIDED WAVE™ Gold Braze Sealed QC LAB SST probe was designed to work with the fiber optic-based LAB NIR-O Analyzer or other FT-NIR Process Spectrometers. The LAB SST probe’s high optical ...

Our GUIDED WAVE™ O-Ring Single Sided Transmission Probe (O-SST) is the ideal in-process fiber optic probe for corrosive process streams containing strong acids, bases, or cyanides. The O-SST performs similarly to our popular gold alloy ...

FTC offers six Perspex and one stainless steel conical probes with angles ranging from 15° to 90°. Cone penetrometry is traditionally used within dairy products to assess hardness and spreadability. It has also found application in ...

Food Technology Corporation’s heavy duty range of probes are made from stainless steel and can be used for higher force or corrosive applications where strength and robustness are critical. Ideal for compression, penetration and puncture ...

Available in either 1mm or 2mm diameter, the FTC needle probes are used on fruits, vegetables, confectionery, cosmetics and fats. Values relate to firmness, yield, consistency and even skin or coating characteristics. Solid cosmetic ...

The head transmitter is designed for direct mounting on the pH- or redox (ORP) electrodes with input lock nut connector B. The output signal is located at output connector A. The electric connection is realized with a standard 8-pin round ...

The pH and ORP converter UNICON-pH is suitable for pH and ORP measurement in food technology, chemistry within pharmaceutical and sewage-water technology. The converter works with all common pH- and ORP electrodes. ●Field or head ...

The GPHU is used in control, measurement and monitoring tasks, e.g. in environmental and medical technology. Any standard pH electrode with a BNC or Cinch socket can be used for the GPHU. In addition, the GPHU has a Pt1000 temperature ...