The ROYALPROBE™ HFX is the world’s first liquid NMR probe switchable between single tune and dual tune mode on the High Frequency coil without compromising the NMR performance. The ROYALPROBE™ HFX operating in single tune mode has the performance for ...
Jeol
... Overview
The TetraCon® 700 IQ is a submersible, electrode‑style conductivity probe designed for continuous, reagentless monitoring with the IQ SensorNet process monitoring system. Its 4‑electrode measuring cell minimizes polarization and reduces ...
YSI
... Salt Water Conductivity sensors from Aanderaa are compact, fully integrated sensors for measuring water conductivity. Measuring conductivity of salt water is a key parameter for in-situ measurements of several fundamental physical properties of water. For ...
... The Honeywell 5000TC conductivity sensors are specifically designed for monitoring conductivity, chemical concentration or salinity in complex processes where coating, fouling, corrosion or high temperatures and/or pressures are a concern. Conductivity ...
... Optical dew-point sensor for online measurement Hygrophil DTP 1500-10 HYGROPHIL DTP works according to the patented method of internal total reflection. The sensor can be installed directly into the compressed-air line and thus determins the exact pressure ...
BARTEC
... This is a four-pole graphite conductivity smart sensor using RS485 communication interface and Modbus RTU standard protocol. Corrosion-resistant shell, built-in PT1000 temperature sensor and compensation algorithm, suitable for various harsh working ...
Fully Integrated: With the ProBus™ interface, the AP033 becomes an integral part of the oscilloscope. The probe sensitivity and offset can be controlled from the oscilloscope front panel, the probe front panel, or by using remote control commands (GPIB ...
Teledyne LeCroy Europe
... Overview The FES-210L Series sanitary conductivity sensors are electric sensors that target sanitation issues by employing a flat structure that keeps dirt from adhering to the tip of the sensor, and they enable continuous, high accuracy measurement ...
ETS-Lindgren's Model 91550-1 and 91550-1L Current Probes are extremely broad frequency range sniffer probes covering 20 Hz to 100 MHz. Both series of current probes have a calibration available down to 20 Hz, which make them ideal test equipment for such ...
... Myron L® Company’s 900 Series multi-parameter water quality monitor/controller is easy to install, easy to use, and does the job of seven separate instruments single-handedly.
Precisely monitor and control an array of critical water and wastewater ...
... Field Proven Electronics
The unique circuitry of the 750 Series II Conductivity/TDS Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation ...
... Cuts Water Consumption by up to 85% The Myron L® CONTROLSTIK II™ Rinse Tank System dramatically reduces the amount of water used in continuous flow rinse tanks. At the same time, it automatically maintains optimum water purity, ensuring effective rinsing. How ...
Open clamps can be used to measure current in points where the power supply can not be interrupted
Measuring range: -100 °C - 20 °C
The SUTO dew point meter / sensor S220 provides reliable and long term stable dew point monitoring in industrial applications, with a range of -100 … +20 °C Td. It makes it an ideal choice for dew point measurements in high tech requirements and conditions. ...
SUTO iTEC GmbH
Measuring range: -60 °C - 20 °C
... The new generation of the dew point sensors offering compressed air users a plug & play solution to monitor their compressed air quality according to the ISO 8573-1.All transmitter models are available with 2-wire or 3-wire analog 4... 20 mA output signals, ...
SUTO iTEC GmbH
Measuring range: -20 °C - 50 °C
... The SUTO dew point meter / sensor S215 provides reliable and long term stable dew point monitoring in industrial applications, with a range of -20 … +50 °C Td. It makes it an ideal choice for dew point measurements in fridge dryers. The new generation ...
SUTO iTEC GmbH
Measuring range: -80 °C - 20 °C
... Digital sensor for dew point, air humidity, temperature • Pressure-sealed variant with screw thread. • The dew point sensor is intended for continuous monitoring of the dew point in industrial applications. Compressed air systems (refrigerant and ...
Ahlborn Mess- und Regelungstechnik GmbH
... Global Radiation Probe Head / Illuminance measuring head / UVA / UVB Radiation Probe Head • Measuring head in anodized aluminium housing with a plastic dome that is transparent to UV light. • Rain and splash-proof system, additionally with desiccant ...
Ahlborn Mess- und Regelungstechnik GmbH
... pH and Redox Probes • pH One-Bar Measuring Chains • pH Insertion Electrode • Redox-One-Bar Measuring Chain By using reference solutions the calibration of pH and redox probes can be started with the push of a button. As the adjustment is stored ...
Ahlborn Mess- und Regelungstechnik GmbH
... The ParaDish2 works with the SDT340, the SDT270 and the SDT200. It makes long-distance ultrasonic detection possible, allowing you to hear ultrasound waves from more than 300 feet/91 meters away. It’s equipped with an optical viewfinder and integrated ...
... The Flexible Sensor is designed to make airborne ultrasound detection as easy as possible. This sensor is mounted to the end of a flexible, metal tube. Compatible with the SDT340, the SDT270 and the SDT200, the Flexible Sensor bends, allowing you to ...
... With the SDT340 or the ULTRAChecker, the AIRSense can be used for close and mid-range airborne ultrasound and is compatible with the precision indicator set as well as the Extended Distance Sensor. AIRSense is an optional accessory for both ultrasound ...
... HEATED SAMPLING SYSTEM The LCPD BOX is a full extractive sampling probe assembly which extracts the sample gas through a probe & heated filter to remove particulates. FEATURES & BENEFITS The LCPD BOX sampling system uses the Hot Wet Extractive (Wet ...
Soil electrical conductivity (EC) is a measure of the amount of salts in soil (salinity of soil). It is an important indicator of soil health. Soils containing excess salts occur naturally in arid and semiarid climates. The salinity of the soil, irrigation ...
WS102-EC is a smart water quality analysis sensor for Electric Conductive, which can be used to detect and distinguish pure water, mountain spring water, mineralized water, purified water, tap water, sewage, etc. At the same time built-in temperature ...
... PAT Testing Accessories High voltage test probe for Supernova PAT testers ...
Seaward
Earth Probe for use with the HAL 103, HAL 104 and HAL LED available in different lengths.
Seaward
Hipot probe for use with the HAL Series, B255, SafeCheck 8 and STM/L hipot testers available in different lengths.
Seaward
To obtain spectral information of diffuse or specular materials, reflection probes are used. The light from a light source is sent through six illumination fibres to the sample and the reflection is measured by a 7th fibre in the centre of the reflection ...
Avantes
... In order to correct fluctuations and drift from your light source, periodic referencing is required. To facilitate this, Avantes offers this series of reflection probes with a self-referencing feature. The light coming from the light source is bundled ...
Avantes
For some measurements, a reflection probe is needed that can be coupled to two spectrometers and a light source. A good example is a reflection measurement in the UV/VIS and NIR range. For these situations, Avantes offers our reflection probes with multiple ...
Avantes
Measuring range: -100 °C - 20 °C
When purchasing a SHAW dew point sensor, you are buying into over 60 years of proven technical experience. The aluminium oxide sensing technology, used to measure trace moisture in dry compressed air and process gases, is a great example of why you can ...
Measuring range: -120 °C - 20 °C
... The SHAW AcuDew high performance dewpoint transmitter. A robust and reliable, 2 wire, 4-20 mA loop powered transmitter. Utilising the ultra high capacitance SHAW moisture sensing technology, the AcuDew offers superior sensitivity, accuracy, repeatability ...
Measuring range: -100 °C - 20 °C
Intrinsically safe dewpoint transmitter, reliable and accurate, designed to meet the stringent demands of industrial applications. Suitable for the continuous measurement of trace moisture in dry compressed air and industrial process gases. Ideal for ...
Measuring range: -110 °C - 20 °C
... The DS4000 Dewpoint Hygrometer is a panel mounted single-channel Indicator specifically designed to work with an Alpha Moisture Systems online Transmitter for continuous trace moisture measurement in gases and dry compressed air and dry rooms/chambers. The ...
Alpha Moisture Systems Ltd
Measuring range: -120 °C - 20 °C
Accuracy (temperature): 2 °C
... Product overview
The AMT dewpoint transmitter is a compact, loop-powered instrument for continuous trace moisture measurement in process gases and compressed air. It uses ultra-high capacitance aluminium oxide sensing technology for high sensitivity, ...
Alpha Moisture Systems Ltd
Measuring range: -110 °C - 20 °C
The AMT-Ex edition Dew-point Transmitter is utilized for uninterrupted measurement of moisture content in a process gas and can also be employed in compressed air applications. The transmitter has a continuous 4-20 mA output signal in correlation to the ...
Alpha Moisture Systems Ltd
... Application: The voltage take-off punch is able to make an insulated piercing on a low voltage wire to plug a measurement device. Insulated body. Female socket for safety test probe Ø 4 mm. Features: MS-62: cable clamping capacity ...
... Accucarb ZCC probe with zirconium oxide The ZCC probe is a high-accuracy oxygen probe, with zirconium oxide, designed for the heat treatment industry. Introduced directly into the oven, at the same working temperature, it performs the measurement ...
ASCON TECNOLOGIC
... Separate electronics for harsh environmental conditions: In-situ zirconium oxide probe for direct and continuous measurement of the percentage of residual oxygen in the combustion fumes, in harsh environmental conditions where high temperatures and/or ...
ASCON TECNOLOGIC
... Separate electronics for critical process conditions: Extractive zirconium oxide probe for direct and continuous measurement of the percentage of residual oxygen in the combustion fumes in critical process conditions. Equipped with separate management ...
ASCON TECNOLOGIC
... SuperView WX100 White Light Interferometry Probe Functions Measurement function: it can realize high precision Z scanning of sample surface and obtain 3D image. Analysis function: It can obtain 2D and 3D data such as surface roughness, micro-nano-level ...
... The Sonospot - Snaphone, manufactured by Sonotech® is a sound detector of emissions in the ultrasonic frequency range caused by compressed-air leakages and electric partial discharges. It allows a reliable and precise detection even over longer distances. ...
SONOTEC GmbH
... SONOSCAN TS5H Ultrasonic transducer for high temperature Testing Also available as complete set with SONOWALL 70 A-/B-Scan thickness gage, temperature compensation function, armored cable, heavy-duty impact protector, and free SONOGRID corrosion management ...
SONOTEC GmbH
Pipelines, particularly in the petrochemical industry, are often exposed to high pressures, extreme temperatures and aggressive media. In order to avoid accidents, constant quality control is essential. This is done automatically with so-called smart ...
SONOTEC GmbH
The IST AG LFS1305 conductivity sensor offers a typical cell constant of 0.86 cm-1 and a conductivity measuring range from 100 μS/cm to 200 mS/cm within an operating temperature range of -30 °C to +100 °C. However, it easily withstands temperatures over ...
The IST AG LFS1505 conductivity sensor offers a typical cell constant of 0.68 cm-1 and a conductivity measuring range from 100 μS/cm to 200 mS/cm (extended range from 10 μS/cm to 200 mS/cm possible with cell-constant correction) within an operating temperature ...
The IST AG LFS1710 conductivity sensor offers a typical cell constant of 0.44 cm-1 and a conductivity measuring range from 0.2 mS/cm to 200 mS/cm within an operating temperature range of -30 °C to +100 °C. However, it easily withstands temperatures over ...