Temperature: -20 °C - 60 °C
Pressure: 1,000 bar
Voltage: 0 V - 10 V
... Accurate, high resolution, compact, rigid Pressure ranges from 0...250 mbar to 0...6000 bar, as well as vacuum, compound and absolute ranges Changeable reference pressure sensors LR-Cal LPC-S All standard pressure units (plus one self-definable) Conversion ...
DRUCK & TEMPERATUR Leitenberger GmbH
Pressure: 800 mbar - 1,150,000 mbar
... CO2 Zero Calibration Kit for the Guardian NG The Zero Calibration Kit acts as a convenient alternative to bottled gas for checking zero offsets and if necessary, zero calibration. It works by removing the CO2 from the air being drawn into the instrument, ...
... TSC200 is a 1-Wire current sensor with 0.3 to 15A working range and IP30 protection. TSC200-15 is a galvanic isolated 1-Wire current sensor. The sensor provides a low-cost option for AC or DC current monitoring. The 1-Wire sensor is based on fully integrated ...
Teracom
... P18 and P18D transducer are devices destined for the continuous measurement and conversion of relative humidity and ambient temperature into a digital or analog standard signal. Additionally P18D transducer is equipped in LCD display. The transducers ...
... P18 transducer is a device destined for the continuous measurement and conversion of relative humidity and ambient temperature into a digital or analog standard signal. The transducer programming is possible through the RS-485 interface and free eCon ...
DITEL
... Highly efficient pocket-size visual fault locatorthe ideal complementary tool for any fiber-testing technician. The FLS-140 is the easiest way to identify optical fibers from end to end and locate polished connector endfaces. Its red laser shines through ...
EXFO
... - Visually identifies and locates faults in fibre optic cabling - 2.5mm universal adaptor for all ST, SC and FC connectors - Useful over a distance of 5km (3 miles) - Up to 80 hours of operation - Ruggedised aluminium body The Visual ...
temperature calibratorTP 3M255E series
Temperature: -35 °C - 165 °C
Voltage: 110 V - 240 V
... Whether for on-site use in the workshop, in the measuring and test room or laboratory, SIKA temperature calibrators can be used everywhere. A wide range of industries and various application areas are covered. • assembly, commissioning • manufacturing, ...
SIKA
... 1.2/50µs lightning impulse generator up to 24 kV with 40Ohm impedance. High voltage outputs on top plate protected by TC-ST test cabinet. MIG2403 is a lightning impulse generator with voltage wave shape 1.2 / 50us. Applications range from insulation ...
... The heating device is heated by two sections of resistance radiation,it can realize 300-1000℃ experimental temperature, and have a good isotropical, temperature volatility and temperature gradient. In vacuum ,it can received GB. Use Level 0.1 AI Intelligent ...
Measuring transducers MT 4xx are intended for measuring and monitoring single phase or three-phase electrical power network. It has power accuracy class 0,5, according to the standard EN 60 688 and is intended for electricity distribution and energy production ...
Iskra d.d.
Temperature: 40 °C - 400 °C
... KT-H101/KT-H102 are small sized practical calibration equipment for temperature calibration of thermocouples and resistance thermometers. - Excellent temperature distribution is achieved by using a heat pipe. 100mm of long heat equalizing length ...
CHINO CORPORATION
... Digital Wattmeters The M4Y/M4W/M5W/M4M series digital wattmeters can measure the electric power in watts and display the values in numeric form. All models feature a 7-segment LED display for clear indication of measured values. The standard meters ...
... Copper earth bar 8 ways (M10 screws) with one disconnecting link. 8 way earth bar, made with 50 x 5 mm tape, enable connection of various cables or round conductors with tin-plated copper connection terminals (for instance, AT-093K). • Dimensions ...
Fully-automatic measuring dials and precision display testing device for analogue and digital measuring dials, as well as all types of measuring probes with a measuring range of up to 100mm. The measuring results are even more precise with image processing. ...
Steinmeyer Holding GmbH
Primary current: 1 mA - 200 mA
... •Small DC current' s measurements: DC1 mA~200 mA •High accuracy: ±1 %FS±20 mV •Least influence of magnetization: Less than DC1 mA in current level •Convenient Single Supply (+5 V) •Reference voltage (Vref) terminal is equipped. •For the detection of earth ...
... The TQC Low Voltage Pinhole detector enables the user to inspect various coatings on conductive substrates for small defects such as holidays and pinholes using the ‘wet sponge technique’. The grounding clamp is connected to an untreated piece of the ...
... Our kits are a great way to calibrate your Ion Science gas detector to ensure safe operation and functionality to meet your required regulations and code of practice. Our kits can be purchased with demand flow or flow regulators and can be supplied with ...
High-Current Test Probe up to 400 A for use in extreme production environments; compact design; Test of high currents possible; compensation for axial deviations and compensation of contact surfaces unevenness
PTR HARTMANN GmbH
... Handling Tools S&C Handling Tools provide convenient, easy operation of S&C fuses, cutouts, and disconnects, as well as those of other manufacture. Each tool consists of a detachable fitting specifically designed for a particular handling operation, ...
S&C Electric Company
Temperature: 20 °C - 30 °C
Transcom Electronic Calibration Modules (TECM) are ideal for users who want fast and easy calibration of various VNAs. (Refer to 1.2 Vector Network Analyzer Compatibility). This TECMs are powered up via USB or 5.5 DC connector and communicate with VNA ...
Sonel MPI-540-PV is an extremely universal meter, designed in particular for testing photovoltaic installations. The device allows a complete set of tests on the DC and AC side – in accordance with the guidelines of EN 62446 standard. Measuring parameters ...
Sonel SA
The Tester 1006 is made controlling 4 load cells of any weighing system at real time. This unit may be used as either calibrator or peak detector. It is fitted with an upload function for tools like DAT and MC 302. Also, this product is supplied with ...
Primary current: 100 A - 2,000 A
... •Closed loop (compensated) current transducer using an extremely accurate zero flux detector •9-pin D-Sub male secondary connector •Status signal to indicate the transducer state •LED indicator confirms normal operation •Metal housing to improve immunity ...