Other electrical measurement equipment

The flexible fault annunciator series BSM-P - easily and flexibly adapted to your application. The BSM-P is available in 6 different sizes from 8 to 48 signal inputs. Because of its easy and intuitive handling and parameterisation via ...

The networkable annunciators of the series USM provide the functionality and flexibility of the series BSM and add communication interfaces for connection to superior or inferior systems. The new version 4.0 of the USM fault annunciator ...

EES has been known for over 40 years as a manufacturer of reliable and innovative fault indication technology. The indication modules are the simplest form of fault annunciating technology. EES is launching a new generation of the ...

Test equipment for respirator masks acc. to EN 149 Semi automatic equipment for breathing resistance tests consisting of • automatic Mask Test Device INTEGRA DFM 149 • Sheffield test-head acc. to EN 149, rotatable in 2 axis

Pressure: -1 bar - 400 bar

Leak standards / test leaks For the simulation of leaks and for monitoring and adjusting leakage testing systems • various connection possibilities included • pressure ranges from -1 to 400 bar • leakage rates from 0.01 ...

DIFFERENTIAL PROBE P9000 Easily Connect to Hioki Memory HiCorders and HiLoggers for High Voltage Testing Overview • - Compact probe for CAT III 1000V environments • - Wave mode: Observe instantaneous waveforms • - RMS mode: Observe ...

C METER 3506-10 Dual-band 1kHz/1MHz Capacitance Meter for High Speed Testing of Ceramic Capacitors on Production Lines Overview Hioki LCR Meters and Impedance Analyzers range from 1mHz to 3GHz devices to suit a wide range of applications ...

PINCHER PROBE L2001 Measure 0603 (EIA) Chip Components Overview The L2001 Pincher Probe can be connected directly to measurement terminals on Hioki LCR meters, impedance analyzers, and Capacitance HiTesters. Among the targets ...

The DT1102 (PS) Switch Selectable Input-Output Galvanic Isolator provides signal transmission and conversion between DC current or DC voltage signal source and signal processing units. The instruments feature complete 3-way isolation: ...

The DT1102 ROOT (PS) provides galvanic isolation and signal conversion between the transmitter (or another signal source) and the signal processing unit. The transfer characteristics is square root. See figure above for 4-20 mA input ...

The DT1122 transmits the signal of a transmitter (or other signal source) connected to its input to two galvanically isolated outputs. This feature may be required for applications where two parallel signal processors (PLC, DCS) are ...

SAT-AR Battery Internal Resistance Tester Internationally, resistance test is widely applied in daily battery maintenance instead of voltage check, because resistance is important parameter to test battery quickly and accurately worldwide.SAT-AR ...

SAT-AC Battery Conductance Tester is a multi-function and portable digital instrument to test lead acid stationary battery running condition and parameters quickly and precisely. It can display and record many key parameters for multi-groups ...

SAT-12B Double Clamps Earth Tester is widely used in the fields of resistance testing for earth resistance of various equipments and buildings. It also can test the soil resistively and leakage current of earth systems under different ...

Temperature: -35 °C - 85 °C

The LaserTRACER-NG was developed for calibration, monitoring and accuracy enhancement of measuring machines and machine tools. It is a self-tracking laser interferometer that automatically tracks a reflector, and hence allows for the ...

TSC200 is a 1-Wire current sensor with 0.3 to 15A working range and IP30 protection. TSC200-15 is a galvanic isolated 1-Wire current sensor. The sensor provides a low-cost option for AC or DC current monitoring. The 1-Wire sensor is ...

Primary current: 0 mA - 20 mA

TSA200 is a 1-Wire current loop transmitter with 0-20/4-20mA input and IP30 protection. TSA200 is 1-Wire current loop transmitter with 0-20mA/4-20mA input range. The current loop input is galvanically isolated from the interface. The ...

TSV100 is an AC voltage detector with galvanic isolation and IP30 protection. TSV100 is an AC voltage detector with optoisolated open collector output. It detects voltage in two ranges – from 85 to 250 VAC (default) and from 170 to 250 ...

System Test Unit Used for Telemir system, it tests and simulates the IR sensors on Marine version of Rafale.

Aircraft Brakes Tester Tool Test equipment to check aircrafts brakes health and perform preventive maintenance.

Primary current: 5 A - 2,000 A

Current transducer (10 mVAC/1 AAC, 200 A, Ø 15 mm) Model SP201 Jaw opening 15 mm Current transducer 200A AC Out put voltage 10mV AC/1A AC Bandwidth 40 Hz to 5 KHz Safety : for isolated conductor only

50V to 1000V Insulation tester, 600V TRMS Multimeter Model MW9090 Test voltage: 50V, 100V, 250V, 500V, 1000V Insulation resistance: up to 20Gohms Measurement of Polarisation Index (PI) and Dielectric Absorption Ratio ...

LCD voltage and continuity tester Model SEFRAM66 The new SEFRAM66 is an easy-to-use instrument. The SEFRAM66 has been designed, tested and approved according to the EN61243-3 standard. Designed with IP2X test probes, the user ...

Temperature: 5 °C - 40 °C
Pressure: 1.03 bar
Voltage: 100 V - 240 V

Sierra's CalTrak® 500 is an accurate primary standard gas flow calibrator for all inert gases. The 500 is used for calibration and verification of: Mass flow meters Controllers Variable area flow meters Precision in-situ ...

Temperature: 5 °C - 40 °C
Pressure: 1.03 bar
Voltage: 100 V - 240 V

Bring the world’s most accurate flow standard to your lab with the CalTrak® 800. The 800 is used for calibration and verification of: Mass flow meters Controllers Variable area flow meters Also used for the precision in-situ ...

Temperature: 0 °C - 70 °C
Pressure: 1,344 mbar
Voltage: 100 V - 240 V

The CalTrak® XL is the leading high-flow primary standard calibrator on the market today. The XL is used for calibration and verification of mass flow meters, controllers, variable area flow meters, and precision in-situ calibration of ...

Pressure: -1 bar - 250 bar

Modular built, automatic Pressure Calibrator ...MEASURE PRESSURE, VERY SIMPLE... TM40_web - Our modular built Pressure-Calibrator TM40 is unique in its conception. The device is built completely modular. 4 slide-in slots ...

The Transducer, manufactured by ENTES, generally functions by converting electrical signals on their input into analog signals. In addition, this type of transducer is typically applied in control as well as in automation devices.