Refrigeration system components

Temperature: -45 °C - 700 °C

JOFRA DLC Dynamic Load Compensation Systems compensates for the negative effect on calibration accuracy that heat exchange between a dry-block calibrator and the sensor-under-test creates. When a sensor is inserted into a dry-block ...

Pressure: 16 bar
DN: 0.5 in - 4 in
Flow rate: 4 m³/h - 436 m³/h

- Long welded ends to ASMEBPE, ISO 1127 - Clamp ferrule to ASME-BPE, DIN 32676-B - Electropolished surfaces SFV4 (Ra 15 µinch, corresponds to Ra 0.4 µm) - PTFE seal with minimal dead space (PTFE cavity fillers) - FDA-compliant ...

Temperature: -30 °C - 200 °C
Pressure: 0 bar - 30 bar
DN: 13 mm - 50 mm

- Port DN 13, 1/2"; DN20, 3/4"; DN25, 1"; DN32, 1 1/4"; DN40, 1 1/2"; DN50, 2" - G-thread to DIN ISO 228-1 or NPT-thread to ANSI/ASME B 1.20.1 or Rc-thread to DIN 10226-2 - Medium pressure 0 ... 30 bar - Valve function 2/2, NC (Normally ...

Temperature: 0 °C - 150 °C
Pressure: 0 bar - 6 bar
DN: 6 mm - 25 mm

The easy way to control media flows Whether you're looking for normally closed or normally open solutions, the pneumatic pinch valve VZQA enables you to control media flows – such as granulates, liquids containing solids or highly viscous ...

Temperature: -40 °C - 400 °C

The compact infrared temperature sensor has the measuring range of -20°C to 350°C. With an optical resolution of 10:1, its spectral range is 8 to 14µm. It works in ambient temperatures up to 75°C without cooling. It is equipped with an ...

Temperature: -40 °C - 1,030 °C

The thermoMETER CSmicro is a temperature sensor manufactured by Micro-Epsilon. It is suitable for applications with limited installation space. The device can measure temperatures within a range of -30°C to 1600°C, with a maximum temperature ...

Temperature: -40 °C - 100 °C

Model TF41 ambient temperature sensors are used for temperature measurement in external areas as well as in cold rooms and production and storage facilities. The extremely small housing even enables mounting in locations where there is ...

Pressure gauge cocks provide the opportunity to either vent the connected pressure gauge according to the position of the handle (venting position), i.e. put it into a pressure-free state, or to vent the pressure measuring instrument ...

The 316L stainless steel AVM7 is a maintainable thermostatic air vent for removing air and other non-condensable gases from clean steam systems. Featuring minimal crevices, the AVM7 operates close to steam temperature.

Current: 23 A - 1,600 A
Power: 7.5 kW - 800 kW

The DIGISTART D3 electronic controller is optimized for use in transient operations in conveyors, compressors, pumps, fans, grinders, kneaders, and the like. The D3's compact design features automatic start optimization, and an incorporated ...

Current: 32 A

The Compressor Soft Starter CSS-25U / CSS-32U is used for switching, protecting and starting current limitation of single phase compressors in residential heat pump applications. Features • For motors with maximum operating current ...

The products in the T-series are valves of type take-apart, which come with an adjustable superheat feature, and interchangeable, replaceable components. Suitable for field replacements, as well as other applications such as heat pumps, ...

TX7 series of Thermo™-Expansion Valves are designed predominantly for AC, heat pumps, close control and industrial process cooling applications. The TX7 is ideal for those applications requiring hermetic / compact size combined with stable ...

Temperature: -50 °C - 100 °C

The Danfoss Temperature sensor type AKS 11 and AKS 21 are devices built for accurate temperature monitoring. Both variants has framework that strictly complies with an IP 67 protection class and temperature tolerance requirements of DIN ...

Temperature: -40 °C - 80 °C

The AKS 12, PT 1000 temperature sensors from Danfoss can be helpful in providing better functions for monitoring temperature. This sensor has air temperature with average temperature range and average time constant. The sensor has a resistance ...

AVTA thermostatic valves with temperature sensitive sensors are made use of around the world. They are designed to be used in various kinds of equipment and installations which require effective and reliable cooling and precise self-regulating ...

Temperature: -196 °C - 25 °C

The T10 temperature sensors are NTC (Negative Temperature Coefficient) thermistors, meaning that the resistance of the NTC decreases with increasing temperature. The T10 temperature sensors are compatible with the RMS-MLOG-T10-868/915 ...

SAMPLING COCK FOR WINE TASTE - STAINLESS STEEL 316

SWEP has achieved a breakthrough in compactness with ADWIS, one of the smallest air dryers on the market. The ADWIS combines two BPHEs (a refrigerated heat exchanger and a recovery unit) sandwiching an integrated separator in a modular ...

Temperature: -200 °C - 0 °C

The long-range wireless data logger LoRa® SPY T3 measures and records ultra-low temperature thanks to an external probe Data are sent to the JRI secure Cloud by LoRaWAN™ network of the telecom operators members of the LoRa Alliance™, ...

Temperature: -50 °C - 105 °C

The long-range wireless data logger LoRa® SPY T2 measures and records temperature in the refrigerator thanks to an external probe Data are sent to the JRI secure Cloud by LoRaWAN™ network of the telecom operators members of the LoRa ...

Temperature: -30 °C - 70 °C

The long-range wireless data logger LoRa® SPY T1 measures and records temperature and door opening at each step of the supply chain Data are sent to the JRI secure Cloud by the LoRaWAN™ network of the telecom operators members of the ...

At Frick® by Johnson Controls, we engineer our Vertical Accumulators to provide protection for refrigeration vapor compressors by preventing occasional liquid in the suction line from entering the suction of the compressors. Our high ...

Operating pressure: 1 bar - 13 bar
Discharge capacity: 0 kg/h - 167 kg/h
Operating temperature: 2 °C - 65 °C

Automatic mechanical condensate drain AOK 13PA has been developed for fully automatic discharging of condensate or any other non-aggressive fluid from compressed air system. The unit can be installed as external drain on any application ...

Tapping of water is also possible during frost periods because the hydrant is completely emptied when in „closed“ Position. Simple emptying per Drainage. Wear-free operation due to the use of ceramic disks. Water jet and flow rate are ...

Constructed with either PE, PP and PTFE polymers, the StopCock spigot is designed for installation on containers with 3/4 in (19 mm) connection threads. Its rotating spout guarantees drip free use and water tight installation. Also, when ...

Developed and engineered by Bürklem, this compact range of stopcocks for barrels and canisters are characterized by their miniature build. The compactly built discharge component is designed to not stick out beyond the container's lower ...

Specifically made to be sturdy and a high quality ball valve, the IBC discharge valve have a hose connection and connection adapter. It is suitable for connection threads with S 60x6 external or 2" internal sizes. it has a discharge valve ...

Form J Push-in RTD temperature probes with extension tube（TM1403) Applications: HVAC, Heating systems, Refrigeration and mechanical equipments etc. Technical data Protection tube：stainless steel 304/316 Sensor element: Pt100, ...

Temperature: -30 °C - 105 °C

MFE-1 series temperature sensor is plastic overmoulding sensor. TPE, PVC material as standard material, with different mounting request it can be injected into different size and type. NTC, RTD elements are most popular sensing element. ...

Temperature: -40 °C - 105 °C

MFT series temperature sensor using the NTC resistance element, according to the different temperature environment or application, through the mature technology, fabricate into a variety of specifications of the sensor, customers can ...

Temperature: -30 °C - 150 °C

MFP-2 series temperature sensor using the NTC resistance element, according to the different temperature environment or application, through the mature technology, fabricate into a variety of specifications of the sensor, customers can ...

Operating pressure: 10, 3 bar

NUTSCHE PRESSURE FILTER AND VACUUM DRYER The Nutsche Filter Vacuum Dryer is a high-quality equipment used in processes of separating solids from liquids. Bachiller's Nutsche Filter / Filter Dryer is designed to perform extraction, ...

PSL’s unique lab filter dryers range called the GFD® is an innovative solution to small-scale synthesis / filtration and drying process development. The GFD is a miniature version of a production filter dryer, allowing scalable lab filtration, ...

PSL’s Filter Dryers are innovatively designed and engineered to a highly ergonomic and efficient standard. 30 years’ experience provides advanced filtration and drying performance along with high levels of safety and quality that meet ...

Operating pressure: 4.5, 6 bar

PSL’s range of Agitated Nutsche Filter Dryers (ANFD) includes small-scale, pilot plant up to production sizes. Thanks to a unique under-plate heating system and special agitator design, PSL Filter Dryers are providing high-performance ...

Temperature: -50 °C - 150 °C

The IST AG 150 °C Pt Temperature Sensor Series offers excellent long-term stability and fast response time with low self-heating within a temperature range of -50 °C to +150 °C. ​The sensors are developed with an insulated enameled Cu-wire, ...

Temperature: -50 °C - 200 °C

The IST AG 200 °C Pt Temperature Sensor Series offers an excellent long-term stability and fast response time with low self-heating within a temperature range of -50 °C to +200 °C.​ The sensors are offered in various standard lengths ...

Temperature: -200 °C - 300 °C

The IST AG 300 °C Pt Temperature Sensor Series offers an excellent long-term stability and fast response time with low self-heating within a temperature range of -200 °C to +300 °C.​ The sensors offer a stable performance at a low price ...

The GIA PREMIX 755 9750 series safety mixers, with ½” BSP, are in fact thermostatic valves, specially made to temper water to eye/face washes. The mixed water can be adjusted by and adjustment screw, although it is set by ...

Universal Mounting Capability Positive Shut-off of Hot Supply when Cold Supply is Lost Built-In Cold Water Bypass Assures Cold Flow Easy Installation and Serviceability Dial Thermometer Rough Bronze or Chrome Plated Finish

Universal Mounting Capability Positive Shut-off of Hot Supply when Cold Supply is Lost Built-In Cold Water Bypass Assures Cold Flow Easy Installation and Serviceability Dial Thermometer Rough Bronze or Chrome Plated Finish

Pressofiltro® Series PF 2000 - PF 14000 Chemical design Chemical design Pressofiltro® agitated Nutsche filters, suction filters or filter dryers are versatile units equally suited for monoproduction applications and for multipurpose ...

Agitated Nutsche Filters, Filter-Dryers Pressofiltro® Series PF 5 - PF 6000 with Containment systems Pressofiltro® agitated Nutsche filters or filter dryers with containment systems provide protection of the operators against ...

Pressofiltro® Series PF 50 - PF 6000 Steam sterilizable design Steam sterilizable Pressofiltro® agitated Nutsche filter dryers are designed to maintain full sterility during the entire process, from inerting through slurry feeding ...

Operating pressure: 42 bar

Features Features removeable end plate for core change access NPT access port for transducer Unique sealing cup design to clean internals when withdrawn Internal spring bearing plate and core mounting kit included

Features Fine oil line filtration Molecular seive beads for POE drying Rugged powder coating

Features Internal U tube design Copper connectors Screened orifice to prevent clogging Rugged powder coating Stud mounting