DN: 2.5 mm
Pressure: 2 bar - 10 bar
Temperature: 0 °C - 60 °C
... Microvalves with plug button 3/2 NO or NC with several actuation options, mechanical or manual. Thanks to the usage of the adaptor all actuators can be mounted on microvalves and it is also possible to combine two microvalves to obtain functions 5/2 ...
A&T Fluid solutions
DN: 0.125 in - 0.5 in
Pressure: 2 bar - 10 bar
Temperature: -10 °C - 70 °C
... The quick exhaust valve allows for rapid air evacuation from the cylinder to increase its speed. It is recommended to mount it directly on the cylinder’s air supply. ...
A&T Fluid solutions
DN: 0.375, 0.5, 0.125, 0.25 mm
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 70 °C
... The stop valve is a pneumatic device that locks the cylinder’s stroke in case of pressure loss in the system. The valves are mounted directly on the cylinder’s supplying ports and do not interfere ...
A&T Fluid solutions
DN: 20 mm - 100 mm
Pressure: 1.5, 10, 40, 25 bar
... range of ball valves with a variety of body and seal material combinations with female thread, male thread or flanged connections. The ball valve dimensions conform to the DIN standard (installation length and connection). Ball ...
DN: 4, 6, 8 mm
Pressure: 0.1 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C
... Orifice Flow Controller Preset Flow Control Valve (Tamper-Proof) preset flow control valve makes constant-flow in one direction and unrestricted flow in the opposite by an orifice restrictor. It is best suited for use ...
NIHON PISCO CO., Ltd.
DN: 3 mm - 12 mm
Pressure: 0.1 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C
... It prevents unnecessary manual adjustments during the operations. Use a slot screwdriver to adjust the needle (speed adjustment). Design without an external needle for speed adjustment. Approx. 2/3 height of the conventional Speed Controller.* Suitable ...
NIHON PISCO CO., Ltd.
DN: 6, 8, 4 mm
Pressure: 0 MPa - 1 MPa
Temperature: 0 °C - 60 °C
... relief mechanism for convenient adjustment of equipment. With reverse flow mechanism. Can be installed between a solenoid valve and an actuator and used as a check-type regulator. A type with a pressure gauge is also available. Mounting ...
NIHON PISCO CO., Ltd.
DN: 15 mm - 200 mm
Pressure: 16 bar
Temperature: -20 °C - 160 °C
... Internal-thread connection, Flange, Butt weld ends, Socket weld ends Design concept Drive: With electric actuator, With handwheel, With pneumatic actuator Casing material EN-GJS-400-18-LT, GX5CRNIMO19-11-2 Nominal ...
DN: 15 mm - 200 mm
Pressure: 0 bar - 16 bar
Temperature: -20 °C - 160 °C
... Weir-type diaphragm valve to DIN/EN with flanged ends, threaded socket ends or socket weld ends, in straight-way pattern; shut-off and sealing to atmosphere by supported and confined diaphragm; body with coating or lining, position indicator ...
AWF
Pressure: 13 bar - 50 bar
Temperature: -29 °C - 204 °C
AWF
Pressure: 3 bar - 35 bar
AWF
DN: 15 mm - 250 mm
Pressure: 10 bar - 100 bar
Temperature: -60 °C - 350 °C
... controller IPC Pneumatic and electro-pneumatic positioner type 8047 - 2-wire - Ex version Positioner with mounting acc. to NAMUR standard Accessories - Metal bellows Limit switch Position feedback Manual override Pilot valve . ...
Schubert & Salzer Control Systems GmbH
DN: 15 mm - 250 mm
Pressure: 10 bar - 40 bar
Temperature: -60 °C - 350 °C
... - IO-Link - Integrated process controller IPC Pneumatic and electro-pneumatic positioner type 8047 - 2-wire - Ex version Accessories - Metal bellows Limit switch Position feedback Pilot valve . . . ...
Schubert & Salzer Control Systems GmbH
DN: 15 mm - 125 mm
Pressure: 10 bar - 40 bar
Temperature: -60 °C - 230 °C
... This compact motor valve is used in a wide range of process engineering control tasks. It is particularly characterised by its very short design. Most media such as steam, fluids, gases, etc. can be excellently controlled with it. This ...
Schubert & Salzer Control Systems GmbH
Pressure: 0 bar - 2 bar
Flow rate: 0 l/min - 120 l/min
... Common industries that use pinch valves for the benefits of isolating fluid from a mechanical valve include: drug dispensing, laboratory equipment, waste water, medical devices, chemical, food and beverage equipment, ...
Clippard
Pressure: 30 psi
Temperature: 32 °F - 180 °F
Flow rate: 8, 0 l/min
... isolation valve like no other... Utilizing the industry's most robust and powerful miniature linear actuator, the patent pending stepper-controlled Eclipse proportional isolation valve leads the industry in performance ...
Clippard
Pressure: 2 bar
Temperature: 0 °C - 70 °C
Flow rate: 60 l/min
... NIV series multi-channel gradient valves feature multiple 2-way, normally-closed PTFE media isolation valves connected around a central body. This unique design provides significant reduction in internal volume with enhanced ...
Clippard
DN: 4 mm - 100 mm
Pressure: 0 bar - 10 bar
Temperature: -10 °C - 100 °C
... Diaphragm valve - 650 The GEMÜ 650 BioStar 2/2-way diaphragm valve has a stainless steel piston actuator and is pneumatically operated. The valve is designed for use in a sterile environment. All metallic ...
Temperature: -20 °C - 40 °C
... Vacuum Valves, 3 Channels, AG Series . Connection on the vacuum network . Electric control . Voltage: 12 VDC / 24 VDC ou 24 VAC / 110 VAC / 220 VAC . NO or NC for the vacuum or compressed air ...
DN: 0.063, 0.125 in
Pressure: 0.5 psi - 100 psi
Temperature: 40 °F - 120 °F
... and changes the pneumatic state. The signal pressure and pneumatic circuit are completely isolated from each other. The pneumatic circuit is normally open, which means the supply port is open ...
AIR Logic
DN: 0.063, 0.125 in
Pressure: 0.5 psi - 100 psi
Temperature: 40 °F - 120 °F
... moves and changes the pneumatic state. The signal pressure and pneumatic circuit are completely isolated from each other. The pneumatic circuit is normally closed, which means the supply port ...
AIR Logic
DN: 0.625, 0.125 in
Pressure: 22 psi - 116 psi
Temperature: 40 °F - 120 °F
... and changes the pneumatic state. The signal pressure and pneumatic circuit are completely isolated from each other. The pneumatic circuit is normally open, which means the supply port is open ...
AIR Logic
DN: 10, 7, 8, 12 mm
Pressure: 15 bar
Temperature: 0 °C - 90 °C
... – Various lines for flexible applications – Mini ball valves also with plug connection Operating pressure See table Materials Handle made of PA66 O-ring made of NBR70 Thread Cyl. thread, DIN EN ISO 228 Con. thread, DIN ...
DN: 10 mm - 45 mm
Pressure: 0 bar - 60 bar
Temperature: -20 °C - 220 °C
... – Various lines for flexible applications – Mini ball valves also with plug connection Operating pressure See table Actuation up to max. 8.4 bar Materials Ball made of brass (Ms58), chrome layer Handle made of aluminium, painted Seal ...
DN: 0.5 in - 2.5 in
Pressure: 3.5 bar - 7 bar
Temperature: -10 °C - 180 °C
... Body Material - SS ASTM A351 Grade CF8 / CF8M / CF3M Seal - PTFE / VITON Circumstance Temp: -10°C to 70°C Actuator Information > - Life: More than ten million cycle > - Other Technical Data: Available Available on request Adjust Stroke Limiter ...
DN: 0.5 in - 2.5 in
Pressure: 3.5 bar - 8 bar
Temperature: -10 °C - 180 °C
... Angle Seat Valve with Plastic Operator (NC/NO/Double Acting) > Body Material: - SS ASTM A351 Grade CF8 / CF8M > Seal: - PTFE / PEEK / VITON Actuator Information > - Cover: Nylon Glass-Filled (Corrosion résistive) with SS Liner > ...
DN: 2 in
Pressure: 4.5 bar - 7 bar
Temperature: -10 °C - 180 °C
... > - Port: Refer below technical data sheet (Available BSP / NPT) > - Body Material: SS ASTM A351 Grade CF8 > - Seal: PTFE / VITON > - CircumstanceTemp: -10°C to 70°C > - Leakage: As per ANSI B16.104 - 1976Teflon seating class IV. For other soft seating ...
DN: 6, 8, 4 mm
Pressure: 0.2 bar - 10 bar
Temperature: 5 °C - 80 °C
... CONTROL VALVES - WITH SWIVEL JOINT ► Configurable flow control valves for regulating the exhaust air ► Optimal for regulating the speeds during piston movements ► Angled version FLOW CONTROL VALVES ...
DN: 7, 4 mm
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 70 °C
... PRESSURE SAFETY VALVE ► For maintaining the position of a double-acting cylinder if the operating pressure drops ► The valve consists of 2 check valves that are unlocked pneumatically ...
Pressure: 10 bar
Temperature: -5 °C - 70 °C
... shortage. DATA SHEET Recommended tubings: accûrding to the fitting connected to the valve. Application field: pneumatic installations fed with filtered, lubricated air. ...
C.Matic S.p.A.
DN: 0.125 in - 0.75 in
Pressure: 2 bar - 10 bar
Temperature: -20 °C - 80 °C
... Quick Exhaust Valve This valve can easily vent the circuit in case of an air supply failure. If assembled on the cylinder port, it increases the cylinder speed. DATASHEET Recommended tubings: according ...
C.Matic S.p.A.
DN: 0.125, 0.25 in
Pressure: 0 bar - 8 bar
Temperature: 0 °C - 70 °C
... installée! in a pneumatic circuit, the pressure control sets the working pressure of ail the connected components. The pressure adjustment will be thereby kept steatfy for a long time. h can also be used as an economuer when connected ...
C.Matic S.p.A.
DN: 25 mm - 400 mm
Pressure: 0 bar - 10 bar
Temperature: 180 °C
... Energy saving valve for the precise and economical control at low loss of pressure of liquids and gases that can be either clean or contain particles. For : Air for aeration in wastewater treatment plant Gases Municipal ...
DN: 10 mm - 100 mm
Pressure: 6 bar
... for the toughest demands! For energy savers → 40% less compressed air consumption! Air operated Pinch Valves with Internal Thread Connection - VMC Series The air ...
Pressure: 7 bar
Temperature: -10 °C - 100 °C
Flow rate: 0 l/min - 250 l/min
... Overview
Proportional
valves convert an analog
electrical signal into a proportional
pneumatic output, enabling fine control of flow and pressure. In medical
air management, this ...
DN: 0.125, 0.25, 0.375, 0.5 in
... Valve Code 4R: 5/2 Hand Pull Valve 3R: 3/2 Hand Pull Valve Series Code 2:200 Series 3:300 Series Position 10: Single Head Double Position Thread Blank: G Thread T: NPT Thread PT: BSPT ...
DN: 15 mm - 100 mm
Pressure: 0 bar - 16 bar
Temperature: -10 °C - 180 °C
... The PJF Series Angle Seat Valve is designed for optimal flow control in industrial applications. It features a robust construction that ensures durability and reliability in demanding environments. The valve is suitable ...
DN: 10 mm - 200 mm
Pressure: 16, 25, 40 bar
Temperature: -20 °C - 180 °C
... The pneumatic ball valve is designed for efficient flow control in various industrial applications. It features a robust construction that ensures durability and reliability. The valve is easy to operate ...
DN: 16 mm
Temperature: -200 °C - 860 °C
... Overview
Air inlet
valve that allows
air intake into the system. The knurled knob facilitates operation even when wearing gloves.
Available items:
- VIA16KF-4/FKM — Materials:
DN: 50 mm - 2,000 mm
Pressure: 6, 10, 16 bar
Temperature: -30 °C - 750 °C
... damper valves type GDV and GDV-T serve mainly for the shut-off and/or flow regulation of different media such as air or process gas. The construction varies from, welded construction to divided structures for bigger ...
DN: 200 mm - 2,000 mm
Pressure: 6, 10, 16 bar
Temperature: -30 °C - 750 °C
... gases, these valves are generally installed on big bag filters or in waste heat recovery circuits, directing the gases to a heat exchanger, or alternatively, to the atmosphere through a chimney. Diverter valves, also ...
DN: 200 mm - 4,000 mm
Temperature: -20 °C - 750 °C
... Damper valves type DV-TD as D (Double) execution are of welded construction and are designed as 100% tight valves to shut-off media such as air or process gas. The design involves injecting air ...
DN: 10 mm - 100 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C
... • Pneumatic Actuator -OF -NC -NA • Robust pneumatic actuator, totally made of plastic • Includes visual indicator of open and closed position • Easy to replace the membrane, only remove 4 screws • Box with two ...
DIVATEC,SL
DN: 10 mm - 100 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C
... diaphragm valve has the highest closing forces in the GF Pipping Systems range of pneumatically operated diaphragm valves. It is available with FC (Fail Close), FO (Fail Open), DA (Double ...
DIVATEC,SL
DN: 10 mm - 100 mm
Pressure: 16 bar
Temperature: -25 °C - 120 °C
... Automatic Ball Valve with Actuators • Pneumatic actuator, double action -OF -NC -NA • Electric Actuator -220V -24V • Special voltages • Includes end of career – Micro switch – ...
DIVATEC,SL
DN: 25 mm - 200 mm
Pressure: 0 bar - 16 bar
Temperature: -20 °C - 60 °C
... flanged ball valves consist of a two-piece nodular cast iron body and are in fire-safe design. The floating ball inside the body, which is chambered on three sides, is adjusted with the handle. Optionally, the handle can be replaced by ...
Pressure: 3 psi - 30 psi
... proportionally to the air pressure: as the analog signal increases, the air pressure will rise and, consequently, as one of the two parameters decreases, the other will decrease. The signal will then flow into the pneumatic ...
DN: 10 mm - 50 mm
Pressure: 0 bar - 10 bar
Temperature: -20 °C - 150 °C
... diameter equal to the diameter of the pipe High flow capacity 2. Pneumatic actuator integrated in the valve Space saving (-60%) and reduced costs compared to an automated valve 3. Piston with ...
OMAL Spa
DN: 0.375 in - 2 in
Pressure: 0.2 bar - 20 bar
Temperature: -60 °C - 225 °C
... resistant stainless steel provides a solution. The sealed and gas-tight design covers an even wider application range. The valves can be conveniently adjusted or aligned using the external adjustment, which means that perfect alignment ...
Goetze KG
the best suppliers