Digital I/O

... TCW241 is an Ethernet IO module, the right choice for factory automation and distributed process control. TCW241 is an Ethernet IO module with Modbus TCP/IP support. It is intended to use for general remote Ethernet IO monitoring and control. The device ...

The ELPRO 115E-2 Ethernet Networking I/O and Gateway is a multiple I/O node that extends communications to sensors and actuators in local, remote, or difficult to reach locations. Designed to work with wired and wireless devices, the ELPRO 115E-2 is capable ...

The RIO40S remote I/O module, based on a CANopen architecture, ensures fast and reliable communication. Ultra compact, it can be easily integrated into any type of cabinet or electrical cabinet. Thanks to its RJ45 connectors designed for quick and easy ...

I-7000 and M-7000 remote I/O modules provide cost-effective protection and conditioning for a wide range of valuable industrial control system. The product line includes sensor-tocomputer, computer-to-sensor, digital I/O, timer/counter, RS-232 to RS-485 ...

... The DAT 3011 device is specially designed to acquire RTD or Tc sensors, mV, V or mA input signals connected to the universal analog input. It is also capable acquire up to 3 digital inputs and to drive one solid-state relay and two SPST relays and is ...

A highly cost-effective, dual-channel CAN card makes the connection between Copley Controls’ distributed control software and CANopen servo and stepper drives. The two independent CAN ports are galvanically isolated to provide greater noise immunity in ...

... Dedicated I/O expansion modules Various models available to I/O requirements Communications via CAN with Centurion™ controller Type J or K Thermocouples or 100Ω Pt 3-wire RTD temperature measurement B+ or B- Digital inputs Low Voltage Digital outputs ...

... Flexible inputs and outputs Integrate with lifts, heating, lighting and more Connects directly to LAN/WAN only 4 mains rated relay outputs per board 4 inputs per board For use with Net2 triggers and actions feature About - The Net2 I/O ...

... DeviceNet Digital Remote I/O (Terminal Block Type/Sensor Connector Type) The ARD-D series digital remote I/O units provide input/output expansion and communication for various devices using DeviceNet protocols. The ARD-D series is available in terminal ...

... Pluggable I/O Module for FP2 and FP4 Series Features Power from HMI Nominal Input Voltage 24VDC Nominal Output Voltage (PNP) 24VDC) Nominal Output Current 250mA @ 24VDC for PNP, 2A @ 230VAC & 24VDC for Relay Max. O/P frequency ...

... VPA 3CG Profibus Adapter VAMP protection relays can be connected to Profibus BP by using an optional Fieldbus card, or via this external device Relay can be monitored from the host system Fieldbus board can be installed inside a VAMP 200 Series relay Normally ...

This product is a remote I/O model CPU unit that has RS-232C *1 and LAN interfaces in addition to four expansion slots. If necessary, you can freely combine this product with CONPROSYS nano series I/O modules. In addition, this product can be controlled ...

... For the S-DIAS system, EPLAN Macros are available for simple integration into the control cabinet. Type - +24 V DC Input voltage - +24 V DC (+18-30 V DC) Input current - 3.5 mA at +24 V Input delay - typically 1 µs Type - +24 ...

... Unit that converts 1 CH of IO-Link ports in IO-Link Master to 16-point of digital I/O Expandable I/O up to 256 (16 x 16) points by connecting to IO-Link Master UR Series. Digital input is Sink(NPN) / Source(PNP), all terminals are switched at once. Digital ...

... The Eckelmann I/O system adapts to your application. From simple digital input, to analog modules, to special and safety modules for high-end applications, the UBM I/O system offers everything needed for an innovative machine concept. The strengths ...

... Module with 4 contact inputs (digital inputs). The monitored contacts are powered by the module. Characteristics • Product type: Datalogger • Usage: Multiple Use • Memory capacity: 10'000 measurement cycles per logger • Dimensions:140 x 70 ...

... 4-Port x4 PCIe interface to support a total bandwidth of 1GB/s Supports four (PoE4) independent GigE Ports Compliant with IEEE 802.3af Single maximum power consumption 23.5W Internal DC 12V Power Input External DC 19-36V Power Input ...

The 8012e Low Profile PCI Express digital interface provides eight optically isolated inputs and eight Reed relay outputs (SPST). The isolated inputs are non-polarized and rated for 3-30 VDC. Optical isolation protects the PC and other sensitive equipment ...

... The system comprises of 12 relay containing make and brake contacts. It also has 8 transistors for outputs and provides over voltage protection. It has a output current of 24V/2A or 48V/1A with a galvanic isolation of 1500Vrms. The output current ...

To transform Revolution Pi into an industrial control unit, various digital I/O modules can be connected to the base module RevPi Core. The I/O modules come in three versions. All have the same 28-pin I/O connector at the front (connector with two rows ...

... Voltage, current, resistance, potentiometer, RTD, thermocouple, strain gage (full-, half-, and quarter-bridge configuration), IEPE High-accuracy digitization 24-bit ADC, 100 kHz sample rate per channel Status, trigger, tare, alarm, command Signal ...

... The Astronics 1260-14 Digital I/O Switch Card provides 96 open collector channels in 12 groups of eight bits each. With the open collector version each independent group can utilize a separate internal or external pull-up supply up to 32VDC. Each channel ...

The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and ...

... -Wall mounting -Base supports 2 I/O modules only (not expandable) -Secure easy-to-use module mounting -Hot Plug-in of I/O modules -Automatic I/O module identification and scanning -Optional module keying Maxiflex 2I/O Master Base for PSU, CPU ...

The 905U and 805U simply and reliably communicate transducer and switch data by providing a 4-20mA, mV and digital interface in a small footprint radio. The sensor data is transmitted to a remote output as digital and 4-20mA effectively replacing the ...

... 10 XS12/8/4/2-SC Digital Inputs 12 Counter and encoder functions 4 Digital Inputs with additional functions Digital Outputs 8 Digital I/O 4 Analogue Inputs 2 CANbus 1 for communication by contact line (spec, driver) ...

... The P371 digital output slice connects the binary control signals from the Motion Coordinator to the machine’s output devices at 24V dc. All 16 outputs are source (PNP) type and have electrical isolation. Outputs and power connection are via 2 x single-row ...

... Overview
The iUSB modules are compact, industrial-grade intelligent I/O systems for measurement, control, regulation and monitoring tasks. Typical applications include industrial automation, laboratory and test automation, process control (MSR), ...

... Product overview
High connectivity, openness and configurability. The new generation of ESA I/Os is engineered to promote efficiency and digitization in accordance with Industry 4.0 and IoT. The ideal solution for distributed control of device ...

... Overview
ESP8266 is a compact MCU with integrated WiFi used to expand I/O for home or industrial automation. Creasol DomESP1 is an expansion board for ESP8266 NodeMCU V3 modules (900 mil header pitch) providing digital inputs, one analog input, ...

The SPiiPlus IOMnt-32-32 (Network Inputs and Outputs Module) is an EtherCAT digital I/O module with 32 inputs and 32 outputs. The input voltage is 24Vdc

... The PE16S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE16, the PE16S offers high performance pin electronics and an enhanced timing generator in a compact, 3U ...

The IOM-CH16 Digital I/O Module can acquire the status of 16-channel digital inputs, or 8-channel digital inputs and 4-channel relay outputs, or 12-channel high-voltage digital inputs, or 8-channel relay outputs. It also supports remote data acquisition ...

The GRV-IACIHVS-12 is an Opto 22 groov EPIC AC discrete input module that senses on/off status from up to 12 field devices using 180–280 VAC and provides channel-to-channel isolation. It is designed for simple on/off monitoring of pumps, fans, motors, ...

The SPC-SDIO-S0808SPK is an intelligent distributed IO module designed by SonnePower for industrial and vehicle control applications. With 8 flexible I/O channels, a CAN bus interface supporting CANopen, and built-in voice alarm functionality, this smart ...

Modular CsCAN remote I/O platform with seamless integration, functionality, and low cost in mind. OCS-I/O is a modular I/O system for OCS offering a fieldbus network (CsCAN). It is a flexible I/O system that can be applied as a local expansion I/O or ...

... 8-Fold Digital Input / Binary Input 10-30V DC for Smart Bulding, IoT, Industrial and Commercial. Industrial 1-Wire Bus. Supports EPuP, Auto-E-Connect Description With the 8-fold digital input module the status of 8 switches, reed contacts or all ...

The BACnet I/O modules allow digital and analogue input values to be connected using the BACnet communication protocol. MS/TP (Master/Slave Token-Passing) based on the RS485 standard is used here. This allows a total bus length of 1,200m per segment with ...

FD-16M Modbus Modular I / O module has designed from a different perspective to automation systems. The FD-16M hardware modular design allows you to solve both your systems in a cost-effective way and to design them in such a way that there are no spare ...

CAN-IO module CIO is a versatile I/O module for the CAN bus. Designed for industrial series applications it has a robust and cost efficient layout. CIO supports eight digital 24 V / 500 mA output and eight analog input channels. The inputs are split in ...