EPDM valves

DN: 10 mm
Pressure: 0.3 bar - 10 bar
Temperature: 5 °C - 60 °C

... , the final closing procedure is due to the buoyancy of the float body. Valves of this design are single chamber valves with the inlet ninety degrees to the outlet. The valve, having ...

DN: 200, 300, 250 mm
Pressure: 16 bar
Temperature: -10 °C - 120 °C

Balancing valves, Balancing valves on cast iron PN 16 (EN-GJL-250) Balancing valve, series PN16. manufactured with body on cast iron EN-GJL-250, bonnet on nodular cast iron EN-GJS-500-7, ...

DN: 0.25, 0.5 in
Pressure: 40 bar
Temperature: -40 °C - 100 °C

... powered mass flow meters red-y compact series. Tightly Closing Valves The valves are tight-closing Different Device Setups The valves are available as straight valves ...

DN: 0.5 in
Pressure: 240 psi
Temperature: 250 °F

... NIBCO® circuit balancing valve features a dezincification resistant brass body, bonnet and trim. The low flow valve is fitted with two test points for differential pressure measurement. The valve ...

DN: 50, 15, 40, 25 mm
Pressure: 16 bar
Temperature: -15 °C - 130 °C

... and reliable control Features Regulating valve free of silicone grease with female thread DIN EN ISO 228-1 G for the control of cold/hot water in closed circuits In combination with AVP 142 and AV 43 valve ...

DN: 0.5 in - 2 in

... diaphragm valve body is of 1-piece molded construction and is not fabricated. For maximum corrosion resistance, the Type-14 diaphragm valve's rugged body and bonnet are manufactured of solid thermoplastic ...

DN: 25 mm - 150 mm
Pressure: 0 bar - 10 bar

Inexpensive shut-off fitting in the hygienic product and CIP section Solidly designed valve disk Safe guidance of the disk thanks to bushes in the housing Seal with a small volume and extension gaps for compensating ...

DN: 0.5 in - 12 in
Pressure: 6, 10, 4 bar

... diaphragm valves are: resisting to corrosion and abrasion, absoluta watertigh and litle cost for maintenance. Seal is done by a membrane that´s pressed by a special pattern embólus against a curve surface seat. Althoug ...

DN: 50 mm - 500 mm
Pressure: 10, 6 bar
Temperature: 180 °C

One-piece body, tight-closing, centric disc With blow-out proof shaft Design for mounting between flanges according to DIN EN 1092-1 Face-to-face length according to DIN EN 558-1-R20 Leakage rate A according to DIN EN 12266-1 For ...

DN: 100 mm - 500 mm
Pressure: 6 bar - 10 bar
Temperature: 60, 150, 185, 200 °C

... GUIDING :Packing gland (faramide / PTFE / graphite) / Slide railsSEALING :Profile sealing ring (PTFE / Murtfeld) and o-ring (EPDM / Viton, VMQ)TIGHTNESS IN THE PASSAGE :Gastight up to 3.0 barü to leak rate BTIGHTNESS ...

DN: 0.125, 0.375, 0.5 in
Pressure: -1 bar - 20 bar
Temperature: -20 °C - 84 °C

... differential pressure, the High Resolution Valve provides superior performance over legacy needle valves. The high resolution electronic flow control valve The High Resolution Electronic ...

... Blowout Proof Stem Optional Seat: EPDM, NRB, VITON, PTFE Double Shaft (2"~12") One Piece Shaft (14" and above) Position Indicator ISO 5211 Top Flange The NUTORK double offset butterfly valve is ...

DN: 150 mm
Pressure: 10 bar - 16 bar
Temperature: -20 °C - 90 °C

Butterfly valve DN 150 PN10-PN16 Lug type GGG40 with notch lever with grey sleeve EPDM DVGW drinking water, WRAS, ACS, W270 sleeves: - EPDM DVGW drinking water, WRAS, ACS, W270 body ...

DN: 50 mm - 300 mm
Pressure: 6 bar - 16 bar
Temperature: -20 °C - 180 °C

• wafer type butterfly valve designed according EN 593 • flange connections according EN 1092-2 - PN6/10/16, ASME/ANSI B16.5 class 150, ASME/ANSI B16.47 class 150 series A • face to face dimension according EN 558-1 ...

DN: 15 mm - 50 mm
Pressure: 16 bar
Temperature: -5 °C - 100 °C

Balancing valve, in dezincification resistant brass with threaded connections, for the flow rate regulation in heating systems.

... machined, and a flat valve face on the upstream and downstream sides of the valve, valves have threaded inserts at both sides of the valve body. This allows them to ...

DN: 1.5 in - 42 in

... for you! Types Ball Valves -Full Bore & Reduced Bore, Cast & Forged Steel, Side & Top Entry Butterfly Valves – Soft Seated & Metal Seated High Performance Gate Valves – Standard ...

DN: 50 mm - 800 mm
Pressure: 10 bar - 25 bar

Wafer type butterfly valve has simple structure, small in size, light weight and good flow control features. Can make wafer and lug types, available with soft seal and metal seal for used in different fields such as ...

DN: 0.5, 0.75, 1 in
Pressure: 1,000,000 Pa
Temperature: -15 °C - 90 °C

... current - < 800MA Open/close time - <15 Sec Life time - 70000 times Valve Body material - Stainless Steel 304 Actuator material - Engineering Plastics Sealing material - EPDM & PTFE Actuator rotation ...

DN: 50 mm - 2,200 mm
Pressure: 16, 10 bar
Temperature: -20 °C - 140 °C

A butterfly valve is a rotary valve (quarter turn valve) using a dise as the closure member. Butterfly valves can be either symmetric or eccentric (=offset), the latter ...

DN: 50 mm - 600 mm
Pressure: 1 MPa

Motorized High Vacuum Butterfly Valve used for Chip Production Industry Electric Butterfly Valve Application DCL electric motorized high vacuum butterfly valves are widely used ...

DN: 15 mm - 100 mm
Pressure: 16 bar
Temperature: 0 °C - 60 °C

EFFAST PVC-U valve BK1 is a true union ball valve ideal for heavy duty applications, chemical applications and water treatment. Technical features: Solvent welded sockets (ISO, BS, ASTM, JIS), threaded ...

DN: 50 mm - 1,000 mm
Pressure: 10 bar - 16 bar
Temperature: -30 °C - 100 °C

Resilient seat gate valves are type of gate valves with an elastomer lined wedge. They are especially used for waste water, drinking water supply fire protection and irrigation, pumping ...