Lubricant pumps

Flow: 5 l/min
Pressure: 2 bar - 7 bar
Head: 70 m

... New pump line with a brand new designing that offers reinforced pumping potentials. The updated designing provides even bigger performance provided with economy Benefits • Optimal performance • Economical air consumption, ecological ...

Flow: 0 m³/h - 42 m³/h
Head: 1.5 m - 16 m
Power: 0.75 kW - 1.5 kW

... fluids. It is also prohibited to position or to remove the pump by the electric cable. Maximum temperature of the pumped fluids: - Continuous duty: 50°C. Minimum pumping level: 10 cm. above the pump body. Maximum fluid ...

... setting of extremely small pressures. The technical data are based on an air inlet pressure of 8 bar. The pumps of course also function perfectly at low pressures. Krautzberger diaphragm pumps are also ...

Flow: 0 m³/h - 60 m³/h
Head: 0 m - 50 m
Length: 330 mm - 800 mm

... the range. There is also a model with a special flange support for hydraulic motors for installation on tanker trucks. These pumps are suitable for transporting various types of liquid, such as oil, wine, liquors and chemical products. ...

Flow: 8 m³/h - 260 m³/h
Power: 0 kW - 15 kW
Fluid temperature: 40 °C

... motor and water pump assembly into one, with simple structure, convenient installation remove, cover a small area, easy to use and maintain, safe and reliable operation, no water polluted, etc. Use Condition: The ...

Flow: 0.43 l/min - 30 l/min
Pressure: 465 psi - 42,500 psi
Width: 180 mm

... liquid pump for pressure testing, chemical injection and hydraulic power. Compact in size, minimal weight and ability to operate in many environments. Hydratron AZ-1 Single Acting Air Driven Liquid Pump ...

Flow: 20 m³/h - 125 m³/h
Pressure: 16 bar
Head: 20 m - 125 m

... base with the motor. How can centrifugal pump pump oil？The support of LQRY series waste oil transfer pump adopts the structure of double-end ball bearing support. The front end is lubricated with lubricating ...

Flow: 55, 70 l/min
Pressure: 8 bar
Head: 0 m - 70 m

... 1/2'' (12.7 mm) Alumınıum Body Dıaphragm Pump Maximum Capacity : 55 lt/min Fluid Inlet-Outlet : 1/2'' NPT Max. Fluid Outlet Pressure : 8 Bar Housing Material : Aluminium Center Section Material : Polypropylene Diaphragm Material ...

Flow: 0.1 m³/h - 300 m³/h
Pressure: 0 bar - 48 bar

... As sludge transfer pumps, the K range is high performance industrial progressing cavity pumps. This PCP, available in block or long coupled configuration, can be manufactured in different materials including cast iron, ...

Flow: 11 l/min
Pressure: 825 bar
Power: 0.37 kW

... self-priming electrig gear-wheel pumps EP are designed to transfer and dispense oil. An integrated bypass-valve limits the max. oil pressure. The pumps feature a protected switch and must be shut off after operation. ...

Flow: max 1200.0 us gal/min
Pressure: max 8.0 bar
Head: 310'00"

... QC Series Centrifugal pumps are built and designed in compliance with 3A Standards, with the following characteristics:• Open Impeller• Volute casing with central suction• Fittings: Clamp (standard), Flange, NPT thread, Weld, Bevel Seat ...

Flow: 0 l/min - 820 l/min
Pressure: 0 bar - 50 bar

... Pumped Liquid Hydraulic oils, synthetic hydraulic liquids, native oils, lubricating oils Main Fields Of Application For generation of pressure in oil-hydraulic systems, lubricating oil supplying, general industrial technologies ...

Flow: 330 m³/h - 48,000 m³/h
Power: 0.37 kW - 15 kW
Fluid temperature: -20 °C - 150 °C

... delivered to the outlet. With this circulation, the medium (material) is delivered through the pump continuously. Universal cam and rotor transfer pump is suitable to tenderly transfer high-viscosity matters or the ...

Flow: 430 m³/h
Pressure: 10 bar
Head: 90 m

... RN pumps Centrifugal pumps with closed impeller according to EN 733 norms. Discharge sizes from DN 32 to DN 150. Use RN pumps can handle clean and non-aggressive liquids for the pump ...

Flow: 0 us gal/min - 6,600 us gal/min
Pressure: 0 psi - 150 psi
Head: 0'00" ft - 300'00"

... TYPE MC Horizontal single-stage centrifugal pump in back pullout design. Pumping of abrasive and corrosive liquids All components which are in contact with the liquid are made of SICcast Suction flange: Axial Discharge flange: ...

Flow: 0 m³/h - 400 m³/h
Pressure: 0 bar - 16 bar
Head: 0 m - 150 m

... The chemical process pump "GCP" is widely used for chemical, Petrochemical industries. Media which can be easily pumped are Acids, Caustic, Amonia, Phoshate, Dyes, Oils, Solvants, Alcohol, Aromatics etc. Also suitable for Textile, Food, ...

Flow: 0 l/h - 43,800 l/h
Power: 0.37 kW - 3.5 kW

... Stainless steel low-speed rotary pumps with flexible impeller; particularly suitable for transfer of delicate, fragile and viscous fluids, also with solid parts in suspension. Our pumps are widely used in the OENOLOGICAL ...

Flow: 28 l/min - 148 l/min
Head: 15 m - 17 m

The best solution for suction and transfer of liquids, thanks to the strong self-priming capacity and the ability to run even with discontinuous presence of the liquid in the suction. The ECC series, made of brass CB754S with DC motor (12 or 24 Volt) ...

Flow: 350 m³/h
Pressure: 16 bar
Head: 100 m

... the seal chamber on these pumps. The ZN series are centrifugal, single stage, horizontal shaft pumps. They have a self-balancing impeller (the balance is achieved through the rear end impeller blades).The dimensions ...

... Please note that the media temperature shouldn't surpass 70° C for common pump and 300° C for anti-high temperature oil pump. The pump has safety valve itself for protection when the pumps ...

Pressure: 150 bar

... The Lubrication Pump AXSP-S with pressure ratio from 25:1 is ideal applicable as feeding pump for ABNOX metering valves or as filling system. ABNOX Air-operated Grease Pump from type ...

Flow: 30 m³/h - 100 m³/h

... DESCRIPTION Advanced OHV, reliable performance, easy start Forged light and strong aluminium alloy Forged iron volute impeller High quality ceramic plunger, silicon carbide water seal Low oil consumption, low noise Suitable for garden, agricultural ...

... peripheral granulated impurity. This device is made up of brass and is designed with a self-priming electric pump design. The self-priming electric pump design helps the device to lift water uo to 9 meters or 29 ft deep, ...

Flow: 60 m³/h - 1,000 m³/h
Pressure: 50 mbar

... appropriate oil lubrication are placed for synchronizing the claws rotation. A built in anti-suck back valve installed in inlet flange will prevent the air from flowing back into the vacuum chamber when the pump ...

Flow: 40 l/min - 86 l/min
Head: 10 m - 30 m
Power: 370 W - 1,500 W

... container without changing any setting. Working principle & Construction BESM pump is blades pump which construction between water ring pump and peripheral pump. So it can get ...

Flow: 0 us gal/min - 7,000 us gal/min
Fluid temperature: 550 °F

... Hot Oil Pumps Most of Cornell’s W, Y, RB and H series clear liquid pumps can be used in hot oil applications, allowing for flows up to 7,000 GPM and heads up to 540′. Features and Benefits: Uniform thermal ...

Flow: 0 m³/h - 550 m³/h
Head: 0 m - 110 m
Fluid temperature: 0 °C - 350 °C

... Heating of baking ovens and large frying units Tempering of tool moulds Production of edible oil and dry masses Heating of calanders, melting pots, agitators and mixing tanks in the leather, rubber and chemical industry and for the production of lacquers, ...

Flow: 0 m³/h - 300 m³/h
Pressure: 100 bar - 500 bar

... Diaphragm Triplex Pump is a fixed stroke reciprocating plunger pump where the process fluid is handled by means of a diaphragm actuated through an intermediate fluid. The reciprocating movement of the plunger displaces ...

Flow: 18 l/min
Pressure: 1 bar
Power: 25 W

... This DC Oil-submerged pump is suitable for use with diesel and biodiesel B30, with battery cable and clips. Do not run dry. Do not pump low ignition oil like Gasoline, Liquefied Petroleum Gas or Alcohol as well as high ...

Flow: 13 l/min
Pressure: 6.9 bar
Head: 67 m

... completely oil-less design. This design means: no oil misting into the environment, no unhealthy working conditions, no oil, lubricants or grease to contaminate your products. Our oil-less design results in lower operating and maintenance ...

... Submersible Slurry Pump by Kosun: 1. The pump shaft under the liquid has enough rigidity. No bearing is set between impeller and pump. 2. Shaft seal is not adapted, the medium with dense solids can ...

Flow: 3 m³/h - 102 m³/h
Pressure: 0 Pa - 1,600,000 Pa
Head: 12 m - 50 m

... drive pump is the new product tested and researched on the basis of CQ type magnetic power drive pump and absorbed the advanced international technique by the technicians of our company according to the requirement of ...

Flow: 3 l/min - 12 l/min
Pressure: 450 mbar - 1,300 mbar

... Pressure/Vacuum Pump Model Series 15000 12VDC Powered Rotary Vane Pumps Gas Flow to 12 LPM DESCRIPTION Model series 15000 rotary vane pumps are an excellent pressure/vacuum source for gas analyzers, ...

... glandless transformer oil pumps. We offer a large range of such pumps, from which customers can choose a type that suits their specific requirements and ensures optimum operating conditions. Get in contact Compact ...

Flow: 0.35 m³/h - 98 m³/h
Pressure: 280, 230, 250 bar
Weight: 0.38, 0.39 kg

... Speed from 500 to 7000 RPM Cost effective design for circuits with a lower operating pressure High quality aluminum alloys pump with axial play compensation Service life for 1 800 operation hours Volumetric efficiency up to 96 % ...

Pressure: 250 bar
Fluid temperature: -29 °C - -17 °C

... and inexpensive alternative to glandless centrifugal pumps. The eSPU6 pumps are not self-priming, which means that the pump circuit must be well vented. Advantages Canned pump: ...