- Detection - Measurement >
- Electrical Measurements >
- Other electrical measurement equipment
Other electrical measurement equipment
Voltage: 0 V - 1,000 V
Multifunction calibrator 9010 is designed as universal calibration tool for electrical calibration laboratories, covering most of their workload like multimeters, clamp meters, ohm meters, power meters and power analysers, energy meters, ...
Meatest spol. s r.o.
Voltage: 0 V - 1,050 V
Multifunction calibrator 9010+ is designed as universal calibration tool for electrical calibration laboratories, covering most of their workload like 6½ digit multimeters, clamp meters, ohm meters, power meters and power analysers, energy ...
Meatest spol. s r.o.
Voltage: 0 V - 1,000 V
M143/143i Multifunction calibrator is cost saving solution for calibration of meters of electric quantities. It offers basic accuracy 0.01% in DC voltage needed for calibration of 3½ and 4½ digit multimeters. Resistance function is covered ...
Meatest spol. s r.o.
Temperature: 5 °C - 45 °C
Voltage: 9 V - 28 V
Introduction Engine RPM Sensor Based on Vibration and Noise Gasboard—8110 adopts advanced design of hardware together with integrated software analysis technology. Petrol engine or diesel engine‘s RPM is obtained through analysis of ...
Temperature: -10 °C - 50 °C
Noise level: 120 dB
Voltage: 9 V
HD9120 is an acoustic calibrator that, in accordance with the Circular Prot. RU 34143 of 02 December 2011, allows qualified technicians to perform calibrations of sound level meters for comparison with a reference sound level meter. The ...
Delta OHM
Extrusion lines for the production of PROFILES The patented MULTIDRIVE technology of the Bausano MD Plus extruder range and a long-standing experience in plastic processing allow Bausano to ensure high performance and great reliability ...
The new AXOS 5 - Compact integrates all of the best features of our stand alone test systems into one single economic solution. It is capable of 5kV EFT/Burst, 5 kV Combination Wave (1.2/50 us & 8/20 us), AC/DC Dips & Interrupts (requires ...
Haefely AG
The Expert Key devices have been specially developed for use in PC-based measurement data acquisition and testing technology. With the appropriate measurement technology software, you can start immediately and record measured data without ...
The universal test device is designed for a wide range of measurement and automation tasks in the laboratory and in testing. Thermocouples, RTDs and other sensors can be connected directly and also electrical AC/DC quantities can be recorded. Various ...
The luminaire testing device, as a compact testing device, enables the heating test of the luminaires to be carried out fully automatically and flexibly. EN 60598-1 standard for CE marking To obtain a CE marking, detailed information ...
Application : Calibration System for Bottom Bracket Bearings Technical Details : Calibration of torque sensors in bottom bracket bearings for bikes. Range up to 100 N·m at 150 min-1. Measurement of torque, speed and angle impulses. Determination ...
Temperature: -10 °C - 55 °C
Voltage: 115, 120 V
The LCc-II load cell calibration indicator uses microprocessor technology to store ten individual, ten point linearized, load cell calibration curves. This capability allows this device to be used as a calibration force measurement ...
Vishay Nobel Transducers
Wire Mapper Pro Model CA7028 The Wire Mapper Pro Model CA7028 is a hand-held structured cable mapping and troubleshooting tester designed for use on UTP, STP, FTP, and SSTP cabling equipped with RJ-45 connectors and wired to either TIA568A/B ...
AEMC Instruments
Easy location of ferromagnetic objects The FerroTec FT 10 helps you safely and reliably locate concealed shaft covers, sliding rods and caps, as well as pavement markers and other objects. The only requirement is that they are made ...
The load cell tester 1008 allows to test and calibrate a four load cell system in only few minutes, using a simple but practical serial cable connection. The LCT 1008 allows for download of measurement results to a PC via an USB or RS232 ...
Nobel Weighing Systems
Temperature: 18 °C - 28 °C
Epsilon’s very high resolution calibrator features 20 nanometers (0.8 microinches) resolution and has 50 mm (2 inches) of measuring range. The 3590VHR calibrator meets the accuracy and resolution requirements for ASTM E83 Class B-1 for ...
Epsilon Technology
Temperature: 18 °C - 28 °C
Epsilon’s standard calibrator features 0.001 mm (50 microinches) resolution and has 50 mm (2 inches) of measuring range. The autozero button and digital display greatly simplify calibration of extensometers. The 3590 calibrator is useful ...
Epsilon Technology
Temperature: 18 °C - 28 °C
Epsilon’s axial/torsional calibrator features 0.001 mm (50 microinches) resolution, and has 50 mm (2 inches) of measuring range axial and torsional rotation where 1.27 mm (0.050 inch) of linear motion equates to 1° angle of twist. The ...
Epsilon Technology
2 to 6 configurable digital inputs number of channels depend on configuration, counter, frequency, PWM, differential or single ended Adjustable thresholds in 256 steps Differential inputs: -20 V up to + 20 V single-ended Inputs: 0 ...
Digital Wattmeters The M4Y/M4W/M5W/M4M series digital wattmeters can measure the electric power in watts and display the values in numeric form. All models feature a 7-segment LED display for clear indication of measured values. The ...
ElectroForce 3300 Series III instruments are well-suited for a variety of tests that include ASTM and ISO standards for materials and biomaterials characterization and long-term durability tests of materials, components and devices. The ...
Using proprietary ElectroForce controls and linear motor technology, the DuraPulse™ Heart Valve Test (HVT) instrument achieves smooth waveform fidelity and precise control for accelerated heart valve durability testing. Automatic PeakIQ™ ...
Temperature: 0 °C - 50 °C
Voltage: 9 V
HI931002 is a portable simulator designed to monitor and regulate 4-20 mA from practically any process meter with or without a voltage generator. HI931002 can measure incoming current, provide power, and simulate 4-20 mA output to calibrate ...
Slotted transparent, with push-on clip Tracks the voltage. Increases your efficiency Unique Wiha handle-length concept for optimum balance of torque and control. Protects your health With the patented SoftFinish® handle design, ...
Mains tester screwdriver for detecting voltage within the 150-250V range Ideal for quick and safe domestic electrical fault finding Clear transparent plastic handle that includes a neon indicator Plastic protection up ...
MULTI-GAS CALIBRATOR FOR AMBIENT AIR GAS ANALYZERS' The MGC101 system automatically performs zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, 03, hydrocarbons and other gases. The MGC101 system automatically ...
Voltage: 230 V
MANUAL CALIBRATION SET FOR UT-3000 This accessory meant for manually calibrating the UT-3000 Mercury Ultratracer The calibration unit is connected to the UT-3000 Ultratracer. With a special syringe a defined volume of mercury containing ...
Voltage: 230 V
This is an accesory for the UT-3000 Mercury Ultratracer in monitoring systems at low to intermediate mercury concentrations The Mercury Instruments Automatic Calibration Unit consists of a specially designed mercury vessel containing ...
Temperature: 5 °C - 35 °C
Multipoint dilution and permeation system developed in collaboration with the METAS (Swiss Federal Institute of Metrology). The most complex configuration consists in a double stage dilution and permeation system. The device can be available ...
LNI SWISSGAS
The Sonimix 3012 / 3022 is a device crafted to manually calibrate or by remote control up to 6 monitors installed in an air pollution monitoring station to measure gases such as SO2, HC, BTX, CO, NOx and O3. It is a multigas calibrator ...
LNI SWISSGAS
The Multipoint Multigas Calibrator Sx 6000C1 is engineered to calibrate either manually or by remote control, up to 5 gas screens setup in the AIR contamination scanning panel like such as SO2, HC or BTX, CO, NOx and O3. With its ...
LNI SWISSGAS
The DTU6 can detect the slightest break in the insulation of a diathermy instrument. Such a break can be very difficult and time consuming to detect visually, yet may be sufficient to give a patient serious burns or the surgeon a distracting ...
Buckleys (UVRAL) Limited
The seam probe electrode is used to test seams and lap joints in single ply membranes. The tool fits directly into the handle or the extension rod of the Dry Roof Pro2, enabling the user to test lap joints/ seams from a standing position, ...
Buckleys (UVRAL) Limited
Voltage: 0 V - 40,000 V
The Buckleys Calibration Meter Pro’ offers a quick, accurate and cost-effective method of checking the calibration state of high-voltage DC equipment. It has been primarily designed for use with the Buckleys’ PHD Pro’, PD and PHD range ...
Buckleys (UVRAL) Limited
For lead-acid batteries until 100 Ah. • Test the starting capacity of the battery. • Indicates the state (good or bad) of the battery. • Test the alternator voltage. It detects if there is aproblem in the load circuit of the vehicle ...
For lead-acid batteries until 160 Ah. 4 FUNCTIONS • Test the starting capacity of the battery. • Indicates the state (good or bad) of the battery. • Test the charge level of the battery • Test the alternator voltage. It detects ...
Very powerful, the battery tester BTW 300 is designed to test the battery and the charging system of a vehicle via a smartphone or a tablet equipped with Bluetooth technology. Easy to use with its dedicated application (to download), ...
Ateq presents CDF60 leak/flow calibrator. It is used to check the calibration of leak and flow measurement instruments. It is also used for testing calibrated leaks and jets. The calibrator is lightweight, small and easy-to-use. It is ...
ATEQ
Temperature: 5 °C - 45 °C
The CDF7000 allows you to check the calibration of leak and flow measurement instruments, as well as calibrated leaks and jets. This portable, compact and user-friendly instrument lets you adjust very accurately your leak or flow rate ...
ATEQ
ATEQ presents CDP60 leak/flow calibrator. It has been dedicated to calibration. It is highly dependable and is traceable to international standards. The calibrator is used for testing the pressure calibration of leak/flow testers. CDP60 ...
ATEQ
TDB series sensors are able to measure AC and DC currents with a DC-10kHz bandwidth, and 1mA resolution. TDB sensors have an integrated degauss function with DC ofset zeroing, which is by relay command. This function sets to zero the ...
FRER
Sensor ø28mm for Type B Earth Leakage Relays B series sensors are able to measure AC and DC currents with a DC-10kHz bandwidth, and 1mA resolution. TDB sensors have an integrated degauss function with DC offset zeroing, which is by ...
FRER
Sensor ø60mm for Type B Earth Leakage Relays TDB series sensors are able to measure AC and DC currents with a DC-10kHz bandwidth, and 1mA resolution. TDB sensors have an integrated degauss function with DC offset zeroing, which is ...
FRER
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining