|
|
Description:
LOW NOISE AMPLIFIER Performance Data
Frequency: 50.0 - 1000.0 MHz
Gain: 21.0 dB Min (Flatness 1.0)
Noise Figure: 3.5 dB Max
P1dB: 12 Min
VSWR: 2.0 Input Max, 2.0 Output Max
Power Supply: 12.0 Volts DC 100.0 mA
Operating Temperature: -30.0 - 70.0 ?C |
|
| Pasternack offers RF Amplifier products to satisfy a wide range of applications. Standard products include In-Line Amplifiers with 18dB of gain and frequencies of 0.5-2 GHZ; General Purpose Amplifiers offering up to 18db gain and frequency operation from 10 MHZ - 3 GHz; and Low Noise Amplifiers (LNA) offering up to 21 db Gain and frequency operation from 0.5-18GHz. |
|
PCB Automotive Sensors Debuts High Temperature Preamplifier
Operating to +120 °C for NVH Powertrain & Vehicle Underhood Testing
The Automotive Sensors division of PCB Piezotronics (PCB®) has announced release of a new high-temperature preamplifier, designed to overcome high temperature testing challenges associated with NVH powertrain and vehicle underhood testing applications, and to broaden options for NVH test engineers collecting acoustic data in high temperature areas.
Automotive engineers routinely perform NVH tests in areas around the powertrain, where elevated operating temperatures can present major measurement challenges. Underhood temperatures can peak at +125 0C under normal driving conditions, and can be significantly higher near turbochargers and exhaust system components, such as manifolds and diesel particulate filters. In the past, test engineers were limited by preamplifiers offering temperature ranges to + 70 °C. Model HT426E01 is a 1/2" preamplifier operating from ICP sensor power, terminating with BNC connector and utilizing standard coaxial cables. The model features a low attenuation factor (-0.06 dB) and low noise characteristics, 4.9 µV, based on an A-weight scale.
Common applications include underhood measurements for benchmarking and issue identification, including engine radiated, induction, ancillary and turbocharger noise; near-field measurements on manifolds; mufflers; exhaust after treatment components; and tailpipe noise. NVH groups within OEMs and Tier 1 suppliers involved with testing of powertrain components will benefit most from this product. |
|
| Incorporate personal video recording capability into cable and DBS set-top boxes and consumer digital video products using Broadcom's MPEG-2 digital video/audio encoder and multiplexer chips. These advanced chips enable manufacturers to develop entertainment systems that support such features as watch and record, selective viewing, fast forward, fast reverse, skip forward, skip back, slow motion and frame-by-frame viewing. |
|
Choose from the industry's largest selection of analog multiplexers in leading-edge small packages. ADI offers multiple configurations from four channels to 32 channels in standard plastic packages as well as in space-saving LFCSP and WLCSP packages. Ron performance is industry-best, with the ADG708 series multiplexers offering 2.5 ohms typical and ADG804 series < 1 ohm guaranteed over the full voltage range and temperature specification.
|
|
We offer the industry's broadest selection of low-on-resistance, high-performance analog switches and multiplexers. Products are available for general-purpose use and specific applications.
|
|
| Analog Devices' amplifiers are the number one selling brand of amplifiers in the world today. Nobody sets more performance standards for next generation designs, with the widest portfolio of leading-edge products. Designers who want dependable, reliable parts that enable the highest performance from their design, come here for the ultimate source in high-speed, precision, rf, broadband, instrumentation, and other amplifiers. |
|
Linear Technology manufactures a broad line of high performance operational amplifiers (op amps) each one designed for the unexpected. Fully specified over temperature, look to Linear for signal conditioning solutions when performance matters. Amplifier product families include high speed amplifiers, precision amplifiers, low noise amplifiers, and micropower amplifiers as well as special function amplifiers such as current sense, programmable gain and differentail high speed analog to digital converter (ADC) drivers.
|
|
Maxim offers the widest selection of operational amplifiers (op amps) and comparators for audio and video applications, battery and power management, and signal conditioning.
|
|
| The VIP50 vertically integrated PNP (VIP) process technology is optimized to perform well at 3.3V and 5V supply levels, enabling direct interfacing with advanced analog-to-digital converters while maintaining a very high signal-to-noise level. The products span a 0.9V to 12V supply voltage range that covers both standard DC single-supply voltage standards and +5V/-5V split supplies common in precision amplifier applications and battery chemistries such as Li-Ion and NiCAD. |
|
Op Amps - Audio-Video Amps - Comparators - Compandors:
ON Semiconductor offers operational amplifiers, audio amplifiers, video amplifiers, transconductance amplifiers, compandors, and comparators. |
|
| The XC221ASeries are input/output railtorail CMOS Op Amp. Operating voltage is 1.2V to 10V in single cell and, 0.6V to 5.0V in +ve /-ve supply. Since the XC221 comes in an ultra small SOT-25 package, theSeries is particularly suited for use with various typed of portable phones. |
|
AMMC-6120
8-24 GHz Frequency Multiplier (Doubler)
Features
Input frequency range: 4-10 GHz
Broad input power range: -11 to +7 dBm
Output power: 14 dBm (Pin = 2 dBm)
Fundamental Supression of 25 dBc
50 ohms Input and Output Match
Supply bias of -1.2V, 4.5V and 85mA
ApplicationsMicrowave Radio Systems
LMDS and Point-to-Point Millimeter Wave Long Haul Platforms
Satellite Communications |
|
Product Overview :
The Optopatch patch clamp amplifier from Cairn Research is a general purpose amplifier, incorporating a number of unique features in order to optimise its performance across a wide range of applications. The amplifier is designed for patch clamp recording, with the unique addition of a lock-in amplifier to enable measurement of membrane capacitance and resistance. This built in device has a unique "track-in" mode that keeps the lock-in amplifier in perfect balance, maintaining discrimination between resistance and capacitance and providing linear calibrated resistance and capacitance outputs. The Optopatch includes several other unique features, including our patented optical technique for measuring small currents over a wide bandwidth (up to 200 KHz), and circuitry for protection against overcompensation of series resistance and electrode capacitance, safeguarding your cells during a recording.
Applications :
Single channel recording
Whole cell recording
High resolution capacitance measurement
Fast, high impedance amplifier
Voltammetry |
|
| Pasternack's Phase Shifters are essential elements in RF coax applications such as phase modulators, frequency up-converters, testing instruments, and phased array antennas with operational frequencies from DC - 40GHz. |
|
Integer-N Phase Locked-Loop (PLL) Frequency Synthesizers
Get maximum signal clarity with our ultra-low phase noise PLL synthesizers: the Integer-N family for demanding LMDS, MMDS, WLL and other base station systems, and our Fractional-N family for handheld and mobile wireless devices. UltraCMOS technology allows monolithic integration for a variety of programming options including embedded field-programmable EEPROM capable of frequency synthesis up to 2.7 GHz and permanent store of control bits. |
|
| ADI offers a variety of PLL synthesizers for use in applications such as wireless base stations, LAN, mobile handsets/PDAs, broadband wireless access, I&I and test equipment, satellite, sonar and CATV. We offer both single and dual PLLs as well as Fractional-N and Integer-N, featuring best-in-class performance, phase noise and integration. |
|
High performance and wide frequency range (765 MHz to 2790 MHz) for various applications requiring a low-noise local oscillator.
Typical Applications:
- 3G basestations
- Data converter clocking
- Wireless LAN
- Broadband wireless acce
- CATV equipment
- RFID
- Bar code scanners
- Automotive applications |
|
A family of RF power detector integrated in loop controllers for PA power control applications in cellular handsets.
|
|
Control Modes Torque
Command Interface UV externally commutated torque commands
Current limit
Feedback None
Configuration Potentiometers
DIP switch
Solderless component header (preconfigured option)
I/O Digital inputs: reset, enable, motor overtemperature
Digital outputs: amp OK, normal, current limited
Analog monitor: actual current (U and V)
Internal Edge Filter Optional - append F to model number
Dimensions 191 x 176 x 69 mm (7.5 x 6.9 x 2.7 in) |
|
|
|
Amplifiers, Analog filters, Digital filters, Signal converters
