|
|
|
CAT PUMPS triplex, high-pressure, liquid handling, PISTON PUMPS are available in five different frame sizes providing flows from 1 to 60 GPM with pressures up to 1500 PSI. Our triplex PISTON PUMP line includes brass Models 280,290,333, 430, 623,820,1010,1520,2520, 6020, 6040 and stainless manifold options for each. Our PISTON PUMPS provide strong suction capabilities and are ideal for CIP cleaning systems, metering and sanitizing applications. Our triplex high pressure PISTON PUMPS feature the UNIFLOW design using a dynamic seal that moves through a cylinder to deliver a constant flow. Our PISTON PUMPS also feature our patented sleeved-piston rods providing piston rod protection and fast, low cost servicing. Request a quote for a pump or custom pumping system.
|
|
GEHO TZPM
The GEHO TZPM pump is a crankshaft driven three-cylinder single-acting high pressure piston diaphragmp pumps. The unique preformed GEHO diaphragm separates the pumped slurry from all the pump moving parts. This range of pumps is ideal to handle abrasive and corrosive slurries against high pressures at the lowest possible total cost of ownership. High efficiency and reliability strongly contribute to this objective. The TZPM pump range is developed and manufactured by Weir Minerals Netherlands b.v.
Features / Benefits
- capacities up to 900 m3/h
- pressures up to 300 bar
- medium viscosity < 8000 mPas
- extreme abrasiveness
- high corrosiveness
- elevated temperature
- up to 8mm particle size
- up to 75% solids content
|
|
Triplex plunger pump for high discharge pressure and flow. Hi-Power pumps are used for various chemical processes and energy production.
* Maximum discharge pressure: standard 50 MPa; maximum discharge flow: 2000 L/min.
* Easy to use with low pulsation
* Various configurations are available to meet process requirements
|
|
Flow rate is based on 100% volumetric efficiency and 20°C ambient temperature
min. inlet pressure depending on fluid medium
min. rpm depending on rod loading
Gear with force-fed lubrication (> 110 kw with oil cooler)
Standard gear ratios: i = 3,00 - 3,14 - 3,39 - 3,76 - 4,13 - 4,50 - 4,93
Also available to API 674
Special medium such as sea water, glycol, methanol, oils, etc. on request
|
|
Flow rate is based on 100% volumetric efficiency and 20°C ambient temperature
min. inlet pressure depending on fluid medium
min. rpm depending on rod loading
Gear with splash lubrication
Standard gear ratios: i = 2,75 - 3,22 - 3,68
Also available to API 674
Special medium such as sea water, glycol, methanol, oils, etc. on requ
|
|
Flow rate is based on 100% volumetric efficiency and 20°C ambient temperature
min. inlet pressure depending on fluid medium
min. rpm depending on rod loading
Gear with force-fed lubrication (> 110 kw with oil cooler)
Standard gear ratios: i = 3,00 - 3,14 - 3,39 - 3,76 - 4,13 - 4,50 - 4,93
Also available to API 674
Special medium such as sea water, glycol, methanol, oils, etc. on request
|
|
Together with our standard stainless steel materials matching, we can offer special stainless steels, titanium or bronze.
Temperature ranges up to 350 degrees C. e.g. pumps for thermo oils.
High capacity - external gear pump
Gear dosing pump Stainless steel gear dosing pump in special design
HP radial piston pump (closed design)
High capacity internal gear pumps with integral pressure limiting valve for low noise operation
|
|
HDP 25 High Pressure Pump Series
Features
- Power ratings up to 30 kW
- Vertical 3 cylinder design
- Wide variety of complementary ancillaries
technical data
- Rod force: 17,6 kN
- Stroke: 30 mm
- Mean piston speed at n2; 625 r.p.m. = 0,63 m/sec; 750 r.p.m. = 0,75 m/sec; 900 r.p.m. = 0,90 m/sec
|
|
High Pressure Pump Series HDP 485
Features
- Power ratings up to 450 kW
- Vertical 3 cylinder design
- Wide variety of complementary ancillaries
technical data
- Rod force: 200 kN
- Stroke:100 mm
- Mean piston speed at n2; 315 r.p.m. = 1,06 m/sec; 380 r.p.m. = 1,27 m/sec; 445 r.p.m. = 1,48 m/sec; 465 r.p.m. = 1,54 m/sec
|
|
FORDIA’s Elepumps are the best light-weight, high pressure plungers in the industry.
ELEPUMP KF
The Elepump KF is a heavy-duty high pressure water pump designed for high-demand drilling. Its triplex water plungers offers up to 45 gallons per minute. The new design of the pump features new frame design for increased life expectancy; stainless steel manifold; and new leakage free seal design. The result is a pump that promises long life, minimal down time, and greatly reduced operating costs,
Designed for simple maintenance, Elepump KF requires only periodic oil checks and changes - and worn parts can be replaced quickly and simply without special tools.
|
|
The Hypro 2535S triplex plunger pump is designed for durability, top performance, and convenient servicing. It achieves up to 38 gpm (144 lpm) and 1200 psi (83 bar). The 316 stainless steel two-piece manifold minimizes washout and corrosion. A strong power end including oversized crankshaft, bearings, and connecting rods easily handles abuse caused by start-up and intermittent operation.
Backed by the best warranty in the industry, Hypro pumps are designed for, and not adapted to, the car wash industry, resulting in pumps that deliver higher pressure and increased reliability.
|
|
KD716 is a serial pump in sturdy design for low viscous liquids, available in various drive and liquid end configurations.
Options
- special lubrication for inclined pump installation
- integrated water/oil cooler
- integrated gear box for direct drive
- noise hood for power end
- suction valve release for by-pass operation
- pressure gauge connection on discharge side
- suction pulsation damper
|
|
|
WOMA designs, produces and sells high-pressure plunger pumps driven by electric motors or combustion engines. The can be run in stationary mode but are also suitable for mobile use. The pumps have power ratings up to 780 kW, operating pressures up to 3000 bar, and volumetric flow rates up to 1679 l/min.
|
|
Wright Flow Technologies proudly introduces its latest innovation in Positive Displacement Pumps for the Sanitary and Industrial Markets, the new RevolutionTM the first true CIP (Clean in Place) Hybrid Circumferential Piston & Lobe Pump.
The RevolutionTM merges the benefits of Lobe & Circumferential Piston technologies into one platform. This new platform delivers:
* Increased product yield
* Increased lifetime of components
* Reduced maintenance costs
* Outstanding CIP cleanability and higher standards of hygiene.
|
|
|
|
|
|
Universal application
ATEX-certification
Certificates for all European countries
Patented pre-chamber
Small. Strong. Durable
Since 1994 we have been producing a specially developed pump for vapour recovery. A small, robust unit. which is suitable for both new installations and retrofitting. It works precisely and reliably at temperatures between -40° C and +60° C.
Permits and advantages
ATEX certification in compliance with Directive 94/9/EC, which is binding within Europe as of June 30th 2003, is already standard.
Also standard is certification for all European countries, which have statutory regulations governing vapour recovery stage II.
The patented pre-chamber increases the durability of the pump against condensate and liquids. A clever drainage system protects the crankcase from the condensate created and also means the pump can be fitted in a range of positions.
Reliable and safe operation is absolutely vital. Tried and tested more than 150.000 times with a very high service life.
You can choose the type of drive: either direct or belt drive.
Flame arresters, which have been specially developed for our product, have been fitted to the intake and outlet side of these compact and lightweight pumps.
The MEX 0831-11 can be used both with mechanical and electrical proportional valves - speed regulation is available upon request. The UL licence is in progress.
|
|
THE LPRP PUMPS
This is the ideal pump for low flow rates and low discharge pressure.
Available flow rates: 2to 50 L/min
Pressure up to 150 bar at slow speed
Available for all cryogenic gases including LNG
Low operation cost
0 m of NPSH
Large scale of feature with numerous options
|
|
Positive constant displacement, rotary, three screw pump. Flow rate per revolution 9.8 - 307 cm3 in 14 steps.
The three screws, the central driven screw – the power rotor – which meshes with the two sealing screws – the idler rotors –are the only rotating components ot the pump. The axial pressure and friction loads on the pump rotors are hydraulically balanced. The power rotor is positioned axially by the selfcompensated thrust washer arrangement, being part of the hydraulic balancing system of the power rotor. The pump accommodates mechanical shaft seals complying with the DIN 24960 Standard.
|
|
|
High overall efficiency at very low speed. Low noise. High speed range. Above-average lifetime. Optimal price / performance ratio. Continuous self lubrication and cooling through the inflow.
|
|
|
Diener Precision Pumps manufacture the highest quality and most accurate precision reciprocating piston pumps in the world. With flow ranges from 0.01ml per stroke up to 5ml per stroke our pumps are designed to give optimum performance over a wide range of applications, including chemical dosing & metering where a controlled volume of fluid needs to be achieved consistently.
|
|
Micropump's valveless piston pumps offer a high level of accuracy and reproducibility when pumping both high or low viscosity fluids or thick and abrasive media. Pump designs feature a no-check valve construction that virtually eliminates clogging and maintenance concerns in a compact package size offering cost effective solutions from many applications
Performance Summary
- 0.94 ml/rev displacement
- 6.89 bar max. rated differential pressure
- Viscosity tested to 5000 cps
|
|
|
Kinney KC & KTC Series Multi-stage rotary piston vacuum pumps provide pumping speeds of 5-112 CFM (8-190 m³/h) with ultimate pressures of 0.2 milliTorr (0.027 Pa). Our KTC series vacuum pumps include our exclusive triplex piston design to eliminate vibration.
|
|
The outstanding performance and flexibility of Gast oilless Rocking Piston air compressors and vacuum pumps, available in standard, twin and miniature styles, make them the ideal choice for countless applications.
· Bonded piston rod and bearing assembly will not slip, loosen or misalign, providing years of trouble-free performance
· Exclusive long-life cup material ensures extensive service-free operation
· All wetted aluminum parts are treated for corrosion protection, offering greater durability in demanding applications
· Rigid motor shell and superior motor-to-pump alignment gives tighter tolerances and allows more consistent performance and noise levels
|
|
Swing Piston Compressors and Vacuum Pumps for Air
Swing piston compressors produce oil-free compressed air and vacuum. They will evacuate, transfer and compress air without contamination. The KNF swing piston system offers a higher flow rate for a given size than the corresponding diaphragm pumps.
|
|
|
|
|
|
Dual pump high flow high pressure pump unit type BMS
Whenever high flow and high pressure is required, the Resato BMS will provide it. Quick testing or testing of large objects is possible with an optional high flow low pressure air driven pump. This additional pump can be a single- or double acting one.
The Resato mobile pump unit is a self-contained air-driven unit of proven design. Not only can it be used to pressurize valves, fittings, hoses, piping, vessels and wellhead equipment, but is also suitable for supply of hydraulic power to operating cylinders, presses, rams, jacks, bolt tensioners and actuators.
All components, including the necessary connecting materials and tubing are built together in a stainless steel frame complete with stainless steel tank or direct water feed connection. The Resato Portable Power pack is manufactured according to European regulations and will be delivered including:
Operating-, Maintenance- and spare parts manual
Test certificate.
Calibration certificate for gauge and / or recorder.
WE ARE LOOKING FOR A DISTRIBUTOR IN ITALY. Please contact us if you are interested!
|
|
|
FMI pumps are modular in design.The Pump Head Modules can be easily removed for cleaning or replaced with a spare pump head for use with different fluids. Some customers have separate pump heads for use with each fluid handled or flow rate desired.
|
|
Dry running piston pump. Well suited for applications requiring high pressures. Mainly used as a compressor.
Free flow: 365 l/min
Pressure: 12 bar max.
|
|
|
These pumps are positive displacement pumps designed to economically transfer small volumes of fluid at low discharge pressures. The lightweight, compact pumps are self-priming, corrosion resistant and can handle viscous fluids. These features make the pumps ideal for high volume copy machines, scientific and laboratory instruments and other chemical dispensing applications.
|
|
|
ARO piston pumps provide industry proven dependability, economy, and precision control for the delivery of a wide range of flowable materials. The efficient, simple design and construction of ARO piston pumps are the reason they are recognized as one of the most dependable, versatile and accurate on the market. Whether you’ removing a small amount of low viscosity fluid a few feet or a large amount of high viscosity material a longer distance, ARO has a pump to meet your application needs.
|
|
|
Rotary piston pumps for corrosive media and very accurate dispensing, various pump heads are available, flow rates up to 2,3 liter/min
|
|
As well as diaphragm and cup seal pumps, we produce unique linear-shuttle pumps.
They have only a single moving part, making them far more efficient and reliable than traditional pumps.
The airflow of this linear piston models lies between 0,8 l/min up to 80l/min, the maximum ratet pressure is 2 bar.
Please get informed about the whole range of our pumps under www.nitto.de or have a look at the category catalogues here at direct industry.
|
|
|
|
Piston pumps, Plunger pumps
