Regulating valves

Overview Bellows sealed globe valve for chemical applications with safety gland packing in straight type, y-type or corner-type; with flanges or buttweld ends; can be supplied in carbon steel 1.0619 / WCB, stainless ...

DN: 15 mm - 800 mm
Pressure: 40, 25 bar
Temperature: -10 °C - 200 °C

... 1092 full bore KLINGER Ballostar-KHI - 2-piece Ball Valve Ball valve for rough use! For use everywhere reliable functioning is required, where large nominal diameters are used and where ...

DN: 150 mm - 1,000 mm
Pressure: 25, 40 bar
Temperature: -10 °C - 200 °C

... customers requirements full bore KLINGER Ballostar-KHI - 2-piece Ball Valve Ball valve for rough use! For use everywhere reliable functioning is required, where large nominal diameters ...

DN: 15 mm - 50 mm
Pressure: 40, 16 bar
Temperature: -10 °C - 400 °C

KLINGER KVN DN15-50 Piston valves, flange design. Features DN 15 - DN 50 piston valve valve rings KX-GT piston made of special niro-steel FTF dimensions acc. to EN 558, GR.1 flanges ...

DN: 100 mm - 300 mm
Pressure: 102 bar
Temperature: 60 °C

... HBC 975 is a safety device, also called slam-shut valve, suitable to quickly interrupt the flow of a gas when the pressure existing in the control point reaches the set calibration value. It is a valve ...

DN: 1 in - 10 in
Pressure: 102 bar
Temperature: 60 °C

... slam-shut valve, the subséquent restoration of the normal operating condition, also cailed RESET operation , is carried out in a purely manual manner, after having verified and solved the causes that led to such tripping. SBC ...

DN: 1.5 in - 6 in

GAS VALVES Floating ball valves Ball valves are cut off devices suitable for use both on natural gas distribution network and for liquid service when high performance on thightness ...

DN: 50 mm - 400 mm
Pressure: 16 bar - 40 bar
Temperature: 280 °C

balanced straight-way valve for medium and very high flow rates | useable for liquids, gases and steam | body made of GGG-40 or GS-C 25 | high precision thanks to integral control behaviour | response time can be adjusted by damping

DN: 15 mm - 150 mm
Pressure: 16 bar - 40 bar
Temperature: 250 °C

single-seat straight-way valve for high flow rates with balanced cone | highest temperatures up to 350 °C | usable for steam | body made of GS-C25 or CrNiMo-steel | steel / stainless steel, stainless-steel-diaphragm body, ...

DN: 50 mm - 400 mm
Pressure: 16 bar
Temperature: 70 °C

Pilot-operated pressure reducing valve for high flow rates | specially developed for drinking water Applications | body made of GGG-40 Epoxy coated, meets the KTW recommendation of the German Ministry for Health | adjustable ...

DN: 6, 4, 8 mm
Pressure: 0 bar - 20 bar
Temperature: 0 °C - 140 °C

... Römer flow and stop valve program consists of throttle, shut-off and check valves. The function fittings offer fine adjustment possibilities for the precise regulation of fluid flows. Throttle valves ...

DN: 0.5 mm - 5 mm
Pressure: 8, 6 bar
Temperature: 0 °C - 80 °C

In the EFC Dispensing valves, the position of the precision throttle directly connected to a stepper motor determines the flow rate. This drive technology allows the set position to be held even without power. Variants ...

DN: 0.5 in - 2.5 in
Pressure: 16 bar - 40 bar
Temperature: -40 °C - 250 °C

Self-actuated flanged or threaded EN or ASA Pressure reducing valve, suitable for steam, gases and liquids for reduce pressure in lines, available in different materials and pressure ranges.

DN: 0.25 in - 0.75 in
Pressure: 40 bar
Temperature: -20 °C - 80 °C

Threaded BSP or NPT direct action pressure regulator valve for steam, gases and liquids for reduce pressure in lines available in different materials and pressure ranges self-actuated.

DN: 0.5 in - 1 in
Pressure: 16 bar
Temperature: 0 °C - 220 °C

Threaded BSP/NPT or flanged direct action pressure regulator valve for steam, gases and liquids for reduce pressure in lines available in different materials and pressure ranges self-actuated.

... aperture control and an externally mixing spray nozzle. The quantity of water injected is regulated by an upstream control valve. This valve adjusts the injection water pressure in front of the nozzles ...

DN: 10 mm
Pressure: 0 bar - 510 bar
Flow rate: 0 l/min - 400 l/min

The pressure relief valve for connecting the DN10 has a maximum liter capacity of 400 l /min. The operating pressure can be set max.510 bar.

DN: 12 mm
Pressure: 0 bar - 510 bar
Flow rate: 0 l/min - 400 l/min

The pressure relief valve for connecting the DN12 has a maximum liter capacity of 400 l /min. The operating pressure can be set max.510 bar.

DN: 1.5 in - 4 in
Pressure: 0.5 bar - 10 bar

... •Control of main valve: by built-in solenoid pilot valve •Applications : For water distribution, where downstream pressure should be reduced, the valve is commanded to open Description G500-PREL ...

DN: 50 mm - 3,000 mm
Pressure: 10 bar - 100 bar

Pressure / flow control valves. Main features : ■ significant reduction in turbulence, vibration and noise ■ fine regulation of the entire range of flow, made possible by the customized trim ■ high precision in ...

DN: 15 mm - 200 mm
Pressure: 0 bar - 40 bar
Temperature: 0 °C - 400 °C

... demands an automatic valve that can reduce steam pressure accurately, reliably and at a cost to suit the application. Self-acting valves (can operate without the need of external power). Pneumatic signal ...

DN: 1.813 in - 56 in
Pressure: 2,000 psi - 10,000 psi

Double Block and Bleed Valve is a side-entry ball valve, with either a bolted or welded body, designed for use in upstream, midstream and downstream oil and gas applications. It requires two in-line isolation ...

DN: 15, 20, 25, 32 mm
Pressure: 25 bar
Temperature: 5 °C - 120 °C

... Series 3-way threaded control ball valves are used either as mixing- or diverting control valves in closed loop hydronic HVAC systems, with chilled water or hot water, and glycol content up to 50% concentration. Valves ...

DN: 20 mm - 150 mm
Pressure: 52 bar
Temperature: -60 °C - 120 °C

The ICM motor operated valves from Danfoss ICV Flexline™ series are quick and simple to handle, install and service due to their low weight and compact design. The valve is designed to regulate the expansion ...

DN: 15 mm - 50 mm
Pressure: 25 bar
Temperature: -15 °C - 200 °C

Special features • - Consisting of single-seated globe valve and actuator • - Flanges or male thread connection and welding or threaded ends or female thread connection Accessories • - Type 2 NI Strainer Options ...

DN: 40 mm
Pressure: 0 bar - 0.6 bar
Temperature: 5 °C - 90 °C

2/2-way direct acting drain valve of nominal diameter DN 40 for controlling low aggressive liquid media, such as cleaning or disinfection agents. Valves of this type are medium separated having a single ...

Pressure: 4 bar - 6 bar

Jet Edge’s patented Dual Pressure Valve is a remotely mounted valve that allows waterjet operators to control water pressure independently of the intensifier pump. This enables operators to run a number ...

DN: 0.5 in - 4 in
Pressure: 17 bar
Temperature: -51 °C - 135 °C

... stringent requirements of the bioprocessing industry Weirless Radial diaphragm tank valves offer solutions to the most challenging applications. It is easy to weld our valves truly flush to the bottom ...

DN: 25, 50, 32, 40 mm
Pressure: 40 bar
Temperature: -60 °C - 450 °C

Blow down valve - straight through with flanges and pneumatic actuator eClass-No.: 37010201 Application: Selection criteria: boiler blow down Application: steam boiler engineering Medium: Cooling water, cooling ...

DN: 0.125 in - 0.75 in

... advanced high-pressure instrumentation needle vah/e for regulating service. The packing boit design, featuring easy mounting. provides the best solution for instrumentation panels. This compact valve ...

DN: 1.813 in - 11 in
Pressure: 2,000 psi - 20,000 psi

... gate valve is designed for positive control of high-pressure frac valves and for many subsea and drilling applications. This design is a combination of our field-proven FLS gate valve ...

DN: 15 mm - 100 mm
Pressure: 63 bar - 100 bar
Temperature: -40 °C - 200 °C

... excursions to which the valve is subjected Greater precision in the alignment of axes due to a unique positioning in the process machining from raw material to finished valve Longer lifetime of the valve Less ...

DN: 15, 20, 10, 25, 32 mm
Temperature: -40 °C - 120 °C

... a normally closed valve which means that it will move to a fully closed position in the event of a power loss. This feature reduces complexity by eliminating the need for an upstream solenoid valve or ...

DN: 8 in - 16 in
Pressure: 450 psi
Temperature: 121, 111 °C

... Type (S)ORIT evaporator regulating valves have a brass body and extended copper connections. They are available with a range of adjustable settings and pressure tap. The primary function of these valves, ...

DN: 0.25, 0.375, 0.5 in
Pressure: 0.1 MPa - 1 MPa
Temperature: -5 °C - 60 °C

・Improved foreign matter resistance ・Increase in condensate discharge 　Drain discharge: Max. 100 cm3/cycle (3 times that of the current model) ・Improved environmental resistance: Transparent bowl guard can protect the inner bowl ・Improved ...