Regulating valves

DN: 0.125 in - 0.25 in
Pressure: 2 bar - 10 bar
Temperature: -10 °C - 60 °C

The selective valve is mainly used to guide or control two different inputs which either chooses one or another but uses only a single a way out.

DN: 3 mm
Pressure: 16 bar
Temperature: -10 °C - 80 °C

VQS condensed drain valves are necessary to secure the optimal status of all different components of a compressed air treatment system. Electric and timed, it’s programmable to discharge the drain in a specific time ...

Pressure: 17.2 bar

... can independently activate an actuator to open the deluge valve: a pneumatic Dry Pilot detection Line and/or an electric solenoid, connected to sensorst hrough a control panel. Once open, the valve reduces ...

DN: 40 mm - 300 mm
Pressure: 25, 10, 16 bar
Temperature: -29 °C - 80 °C

... low flow The hydraulic control valve is the most effective device for automating industrial and municipal water supply sytems or any other system that requires control of changing operating conditions. The hydraulic ...

DN: 50 mm - 900 mm
Pressure: 16 bar - 64 bar
Temperature: -29 °C - 90 °C

... Actuated Hydraulic Control Valve for use in waterworks for pressure reducing, pressure sustaining, pressure relief, flow control, surge anticipation, level control and other control applications. The hydraulic control ...

DN: 40 mm - 1,600 mm
Pressure: 2.5 bar - 100 bar
Temperature: -10 °C - 200 °C

... the request of customers . The gate valve body is made of cast steel and it is suitably dimensioned to assure a high safety factor. The thicknesses are always higher than the mini-mum ones established for GATE VALVE ...

DN: 100 mm - 1,400 mm
Pressure: 2.5 bar - 64 bar

... to utilize devices able to control the distribution of the water without wasting it. Needle valve is especially designed to realize the function of regulating the water flow, maintaining an easy handling ...

DN: 100 mm - 3,000 mm
Pressure: 16, 10, 25 bar
Temperature: -40 °C - 200 °C

... be used as a safety valve (positive safety valve able to close even in case of tampering) In addition to the above mentioned technical advantages there is a remarkable economical benefit as this valve ...

Pressure: 0 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C

This Exhaust Needle Valve controls the exhaust flow rate. The valve can be attached directly to a solenoid valve. Best suitable in case a cylinder, etc has no sufficient space around ...

DN: 3 mm - 12 mm
Pressure: 0.1 MPa - 0.7 MPa
Temperature: 5 °C - 60 °C

Best suitable for high-speed drive cylinder. Possible to control high-speed cylinder. Exhaust needle valve type, whose exhaust port incorporates throttling function, is available. Tube O.D. 3mm is available for ...

DN: 4, 6, 8, 10, 12 mm
Pressure: 0 MPa - 0.6 MPa
Temperature: 0 °C - 60 °C

Pressure control valve saves compressed air consumption. In driving an actuator under high pressure, compressed air can be saved by use of the pressure controller to reduce the pressure only during home return. Controls ...

DN: 10 mm - 40 mm

3 way FFF PVC Diamant ball valve with manual override 3-way FFF PVC with connection kit and emergency manual override Version with threaded or to-be-glued connections Available with T or L sphere

DN: 15, 20, 25 mm
Pressure: 16 bar
Temperature: -10 °C - 110 °C

2 way MM BRASS Diamant ball valve 2-way MM BRASS with caps and tangs Full bore PN16 Code - Size - DN - PN - KVS DC2A2A - 1/2" - 15 - 16 - 16,3 DC2B2A - 3/4" - 20 - 16 - 29,5 DC2C2A - 1" - 25 - 16 - 43

DN: 20, 25 mm

3 way MMM BRASS Diamant ball valve 90° – DIVERTING / MIXING 3 vie MMM in OTTONE con codoli e calotte Passaggio totale PN16

DN: 0.125 in - 1 in
Pressure: 0.8 bar - 10 bar
Temperature: 0 °C - 70 °C

... unidirectional connection, non-return valves, slide valve, quick exhaust valve Flow regulators 041, 042, 043 Unidirectional flow regulator (block shaped) Valves in ...

DN: 0.125, 0.25 in
Pressure: 0 bar - 8 bar
Temperature: 0 °C - 70 °C

... unidirectional connection, non-return valves, slide valve, quick exhaust valve Flow regulators 041, 042, 043 Unidirectional flow regulator (block shaped) Valves in ...

DN: 50 mm - 1,200 mm

Gate Valve with a drain valve body material: Carbon steel /Stainless steel / Alloy steel /Special (Monel /Inconel /Hastelly etc.)/alloy steel/ Al-bronze end connection: RF/RTJ/BW operation: Hand ...

DN: 50 mm - 900 mm
Pressure: 16 bar - 250 bar

... Entry ball valve body material: Carbon steel /Stainless steel / Alloy steel /Special ( Monel /Inconel /Hastelly etc.) end connection: RF/RTJ/BW operation:Lever Gear motor/pneumatic actuators product overview:Athena ...

DN: 50 mm - 1,400 mm
Pressure: 16 bar - 420 bar

... soft-seated trunnion mounted ball valves are designed according to API6D standard and be offered two-piece and three-piece split body designs. The valves can be applied in wide pressure and temperature ...

Pressure: 1.2 bar - 10 bar
Flow rate: 0 l/min - 300 l/min

Pressure: 13 bar - 50 bar
Temperature: -29 °C - 204 °C

DN: 80 mm - 300 mm
Flow rate: 20 m³/h - 1,200 m³/h

This valve is operated by line pressure by means of a 3 way selector valve, this selector has the positions “open”, “close” and “auto”. In the “open” position the valve is fully opened, ...

DN: 1.5, 2, 2.5, 3, 4 in
Flow rate: 5 m³/h - 150 m³/h

Hydraulic control valve used to reduce the inlet pressure to a preset lower level pressure in the outlet by means of a three way plastic reducing pilot incorporated. This valve controls the outlet pressure ...

DN: 2, 3, 4 in
Flow rate: 5 m³/h - 150 m³/h

This valve is operated by line pressure by means of a 3 way selector valve, this selector has the positions “open”, “close” and “auto”. In the “open” position the valve is fully opened, ...

DN: 40, 300 mm
Pressure: 10 bar
Temperature: -10 °C - 150 °C

Cast iron (GJL 250) PN 10 gate valve flat body inside screw stainless steel (AISI 304) trim 150°C (max) Main characteristics • Manufactured in Italy in accordance with EN 1171 • Face-to-face length according to EN ...

DN: 50 mm - 600 mm
Pressure: 40 bar
Flow rate: 16 m³/h - 5,400 m³/h

PROPORTIONAL PISTON ACTUATED VALVE DESIGNED FOR HIGH DIFFERENTIAL PRESSURES The valve maintains downstream pressure to a constant and pre-set rate of upstream value. No pilots needed. The valve ...

DN: 80 mm - 300 mm
Pressure: 1 bar - 16 bar
Flow rate: 10 m³/h - 1,600 m³/h

PRESSURE REDUCING VALVE The valve reduces high upstream pressure to a pre-set lower and constant downstream pressure level, regardless of fluctuating flow or varying upstream pressure. A hydraulic ...

DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h

PRESSURE REDUCING VALVE The valve reduces high upstream pressure to a pre-set lower and constant downstream pressure level, regardless of fluctuating flow or varying upstream pressure. A hydraulic regulating ...

DN: 6.35 mm
Pressure: 250, 160 psi
Temperature: -29 °C - 66 °C

... Pressure Control Valve provides regulated pressure to operate a variety of Williams pneumatic metering pumps. It features an economical pressure regulator capable of output pressures of 0-125 psi (0-862 Kpa). The Pressure ...

... operation is accomplished by using the geared limit switch and the torque switch inside the Limitorque, to move the poppet valve. The rotary vane air motor is compact and powerful. SMBA is ideal actuator for the use ...

DN: 0.375 in - 2 in
Pressure: 10 bar
Temperature: -20 °C - 150 °C

... Coil: The solenoid valve has an electromagnetic coil wrapped around a ferromagnetic core. When an electrical voltage is applied to the coil, it generates a magnetic field around the core. Armature or piston: Inside the ...

DN: 0.375 in - 2 in
Pressure: 10 bar
Temperature: -20 °C - 150 °C

... monitor and adjust the valve position as needed. Fluid Flow: When the engine opens the valve, fluid can flow through the valve opening. The size of the opening can be adjusted continuously ...

DN: 0.25 in
Pressure: 0 bar - 200 bar
Temperature: -20 °C - 70 °C

The rossignol metering valve will be fitted di- rectly to the cylinder valve. Due to the slim conus of the metering spindle the rossignol valve guarantees precise metering. As an ...

DN: 15 mm - 65 mm
Pressure: 0 bar - 10.2 bar
Temperature: 0 °C - 180 °C

... position feedback signal 0-10 V / 4-20 mA (after automatic balance) Control element 2-port/2-way valve, NC (normally closed) as standard, as option 3-port/2-way valve for mixing different media, with ...

DN: 15 mm - 80 mm
Pressure: 16 bar
Temperature: 0 °C - 110 °C

... sensor or thermometer can be added using immersion sleeve spindle thread not in contact with medium wear-resistant valve seat made of stainless steel up to DN 50 with a black handwheel free from dead ...

DN: 15, 20, 25 mm
Pressure: 16 bar
Temperature: 50 °C - 90 °C

thermostatic balancing valve for hydraulic balancing of riser and distribution pipes for hydraulic balancing of hot water return systems (PWH-C), supports thermal disinfection wetted metal parts made from ...

DN: 15, 20, 25 mm
Pressure: 16 bar
Temperature: 50 °C - 90 °C

thermostatic balancing valve for hydraulic balancing of riser and distribution pipes for hydraulic balancing of hot water return systems (PWH-C), supports thermal disinfection wetted metal parts made from ...

DN: 6 mm
Pressure: 700 bar
Temperature: -20 °C - 60 °C

Our manual valve is designed for reliable use with single or double acting hydraulic systems. If desired, it is available with a lock function for secure load holding. Technical data Mounting face Cetop C DIN ...

DN: 0.5 in - 6 in
Pressure: 1 bar - 13 bar
Temperature: -15 °C - 180 °C

Model RET-DS / REF-DS are the Direct Acting Pressure Reducing Valve designed with Duplex Stainless Steel material providng more options for different industries. Pressure Reducing Valve protecting the ...

DN: 3, 4, 6 in
Pressure: 14.2 psi - 170.6 psi
Temperature: -15 °C - 80 °C

... Application of Groove End Pilot Control Pressure Reducing Valve Our Groove End Pilot Control Pressure Reducing Valves are most suitable for Hydraulic systems. Hydraulic Pressure Reducing Valves ...

DN: 1.5 in - 56 in
Pressure: 0.3 psi - 8 psi
Temperature: -15 °C - 80 °C

... Presssure Sustaining Valve, also known as Back Pressure Valve, or Back Pressure Sustaining Valve, is a valve that maintain required pressure of inlet port by opening ...

Pressure: 262 bar

Pneumatically actuated discharge valve for use in systems such as HANDY-H single-line hydraulic barrel pumps or pneumatic pumps. Supply air pressureMax:8 bar Lubrication pressure 241bar Hydraulic pressure required ...

Pressure: 262 MPa

Hydraulically actuated discharge valve for use in systems such as the HANDY-H single-line hydraulic barrel pump. Product main features: Input hydraulic pressure Max: 103 bar Hydraulic oil pressure required to ...

DN: 0.5, 0.375 in
Pressure: 13.8 bar
Temperature: 198 °C

... housing temperature control valve designed to monitor and regulate the flow of steam to maintain a desired temperature inside the enclosure at all times. Operation The TV/SC-I (Tube Valve/Steam Control ...

DN: 3.88 in

... standard GURU® Plug. This thermostatic drain valve responds to the engine coolant temperature and will pop open to rapidly drain the system before freeze damage can occur when the coolant reaches the valve’s ...

Temperature: 35, 40 °F

The GURU® Valve DL2.1 CH and CHS Plugs are self-operating drain valves that are easily retrofitted into water-cooled air compressor heads to protect the compressors from freeze damage when a locomotive ...