Chemical pumps

Flow: 681 m³/h - 1,703 m³/h
Head: 23 m - 125 m

... The Magnum XP pump is single-stage, single-suction centrifugal mud pump. It is suitable for handling big capacity of abrasive, corrosive and plain tough slurries. The small footprint design is specially ...

Flow: 3.62 l/min
Pressure: 830 bar

... The chemical reagent injection system can be used to inject special chemical reagents into the blocked production wellhead to unblock the production wellhead. The device uses compressed air as the driving source and has ...

Pressure: 1,500, 107 psi

... The Air Assist Airless pump from C.A.T. is an all stainless 14:1 ratio pump for production fine finish spraying of wood or other fine finish applications. The new 14:1 Peak Performance Series pump incorporates ...

Flow: 15, 11, 6 us gal/min
Pressure: 307, 207, 172 Pa
Weight: 14.8, 17.2, 15.9 kg

... The Muncie Power S Series hoist pump was designed specifically for use on small single or tandem axle dump trucks. The S Series hoist pump features a roller bearing design and can be air, lever or ...

Flow: 30 l/min
Pressure: 0 bar - 6 bar

... 30 L Double Membrane Pump. Medium production. For finish and primers. High precision product regulator. Anti-pulsation system and double paint filter. Lacquers, clearcoats, basecoats, enamels. Medium viscosity products. ...

Flow: 3 m³/h - 1,680 m³/h
Head: 4 m - 152 m
Power: 0.37 kW - 350 kW

... • The pump shall be designed for clear, clean liquids which are non-aggressive to the wetted parts and non-explosive, without any solids or fibers • Water supply • Pressure boosting for high rise buildings, hotels industry etc. • ...

Flow: 2 m³/h - 75 m³/h
Pressure: 4.5 bar
Fluid temperature: 100 °C

... progressive cavity pumps are used to transfer products of low and high viscosity as well as products containing soſt particles. These food-grade progressice cavity pumps are also recommended for use with edible oils, ...

... mode. Control is easy because all operations are automated. It operates normally in atmospheric pressure state. Emergency manual operation is available . (needs not by-pass line) Body:SCS13A, Ball:Durability is good and strong against corrosion ...

Flow: 0 l/min - 1.6 l/min
Pressure: 10 bar - 200 bar
Fluid temperature: -30 °C - 130 °C

... The HPP 200 is a very compact high-pressure pump that is particularly suitable for pressurization when pumping low-viscosity liquids. The basic version of the pump is designed for a continuous operating ...

Flow: 0 m³/h - 200 m³/h
Pressure: 24 bar
Fluid temperature: 100 °C

... Food-safe pumps with a large suction chamber. Made in polished AISI 304 and/or 316 stainless steel for transferring products of low/medium viscosity. ...

... Pneumatic dosing pump made of stainless steel AISI 316 for doling out chemicals and fluids Main Features Stainless-steel in AISI316 (1.4408) Double- and single-acting versions Seals in PTFE and FPM Packing in ...

Flow: 0.018 l/min
Power: 70 W

... Our peristaltic pumps are used in all fields of analytical and preparative chemistry and in production operations. In particular, they are used in instrumental analysis, biotechnology, bioanalysis, fluid chromatography, ...

Flow: 0 us gal/min - 65 us gal/min
Head: 0'00" ft - 20'00"
Power: 0.4 ch

... Handling fluid temperatures of up to 200°F, Liberty Pumps HT40-Series submersible pump is designed for hot water applications such as boiler blow-down pits, condensate pits and high temperature water transfer. Other features ...

Flow: 10 m³/h - 1,300 m³/h
Head: 7 m - 40 m
Power: 15 kW - 75 kW

... well. It can be used to pump water water containing alkali or acid, such as waste water from building, chemical plant, food factory or sea water treatment. WQ stainless steel sewage pump features 1.The ...

Flow: 75, 160, 210, 245, 280 l/h
Head: 1, 2, 3, 4, 4.8 m
Power: 60 W

... condensing furnace and condensing boiler equipment. ■ External test/run lever ■ Slim footprint ■ Vertical centrifugal pump design ■ Stainless steel motor shaft ■ Automatic start and stop operation ■ Galvanized steel “quick ...

Flow: 100 m³/h - 280 m³/h
Power: 3 kW - 37 kW
Fluid temperature: 80 °C

... made this pump the standard in the industry. The combination of different sized pumps, impeller trims and speed variations ensure that the correct capacity pump will be matched to the exact requirements ...

Flow: 3 m³/h - 3,000 m³/h
Head: 0 m - 150 m

... Capacity: 3~3000m³/h with 2950RPM,1450RPM,980RPM. Max head: 150M Medium Temperature: -20℃~80℃ Material: Cast iron-HT200,HT250;SS304,SS316,SS306L,Duplex SS,Bronze; Motor: 380V,415V,660V;IP54,IP55;50HZ,60HZ; ...

... saving - More hygienic pump - Fully drainable - Semi-open impeller. - Greater efficiency - Volute casing - Up to 800 cP - Design that complies 3A and EHEDG standards - Same footprint of a QC+ Pump Advantages QIS ...

... shavings to be detected inside the pump, the main reason for causing pump damage in the past. managed to design an appropriate bypass in such a way that it can be mounted or replaced without having to take apart the ...

... Excellent for mixing, blending and recirculating a variety of fluids Ideal for the chemical and petroleum markets Cast iron helical gear pump Two-piece backplate for flexible sealing options Many parts ...

Flow: 2,400 m³/h
Pressure: 10 bar
Head: 40 m

... every seal arrengement. Use RB pumps can handle slightly contaminated liquids in waste water treatment plants, clean water for cooling towers or condensate recovery plants, viscous liquids in evaporators in food or chemical ...

Flow: 0 us gal/min - 15,400 us gal/min
Pressure: 0 psi - 1,450 psi
Head: 0'00" ft - 3600'00"

... TYPE HPH Multi stage centrifugal pumps in ring-section design. Pump inlet: axial or radial with flanges positioned at 90° increments Discharge flange: radial positioned at 90° increments Replacable rings in composite ...

Flow: 0 l/h - 43,800 l/h
Power: 0.37 kW - 3.5 kW

... Stainless steel low-speed rotary pumps with flexible impeller; particularly suitable for transfer of delicate, fragile and viscous fluids, also with solid parts in suspension. Our pumps are widely used in the OENOLOGICAL ...

Flow: 0 m³/h - 220 m³/h
Pressure: 0 bar - 40 bar
Head: 0 m - 400 m

... The Osna NMH is a multi-stage horizontal centrifugal pump that is suitable for pumping clear and slightly contaminated liquids in pressure boosting plants, central heating systems, cold and hot water circulation, water supply systems, ...

Flow: 28 l/min - 148 l/min
Head: 15 m - 17 m

The best solution for suction and transfer of liquids, thanks to the strong self-priming capacity and the ability to run even with discontinuous presence of the liquid in the suction. The ECC series, made of brass CB754S with DC motor (12 or 24 Volt) ...

Flow: 3,000 m³/h

... The EN 733 MU Series of End-Suction Centrifugal Pump, manufactured by Pompe Garbarino S.p.A., is specifically designed for fresh and sea water, condensate, oils, chemical and petrochemical products. It is mainly used ...

Flow: 1.4 l/min

... the main pump parts and enable the pumps to be used with strong acids, strong alkalis, and chemical solutions that erode general-purpose plastics. The heat resistance is also excellent, use in various ...

Flow: 750 m³/h
Head: 160 m
Power: 315 kW

... Vertical Reverse Circulation Pump This is a vertical-orientation, reverse circulation canned motor pump, typical for applications involving liquefied gases and refrigerants. Designed for zero-leakage operation in applications ...

Flow: 2.5 m³/h - 100 m³/h
Head: 80 m
Power: 750 W - 45,000 W

... MECHANICAL EQUIPMENT CO.,LTD provides good quality fluorine plastic lined centrifugal chemical pump. IHF single stage end suction fluorine plastic lining centrifugal pump is with disposable sintering. ...

Flow: 4 m³/h
Pressure: 160 bar

... SID SolidPumps is a specialist for piston pumps suitable for the most demanding industrial applications. An undeniable know-how and more than 30 years of experience enable SID SolidPumps to provide services corresponding to highest ...

Flow: 0.1 l/min - 30 l/min
Pressure: 5 bar

... Capable of Parts Replacement/Maintenance Without Removing The Chemical Piping The main body of the pump can be disassembled easily into eight components using only a couple tools. The pump head employs ...

... • Flow rates and prevalence on request • Made of PP or PVDF ...

Flow: 25 l/s
Head: 275 m
Power: 0.37 kW - 37 kW

... fire safety ‘jockey’ systems / system pressure upkeep; boiler feed water pumping DescriptionThe Armstrong 4700 MultiStage Pumps are designed for reliability and low maintenance cost MaterialsCast iron or stainless steel casing ConfigurationInside ...

... The OSIP ZS 65 - 75 - 80 - 100 - 120 - 125 - 180 - 200 - 220 is a low pressure industrial electronic pump. This device is used for pumping liquid coolants and lubricating mixtures. The ZS Series is applicable for systems with high flow ...

Flow: 500 l/h - 1,080 l/h

... head pressure. Its inlet and outlet threaded ports are approximately 1/2". The body uses brass and steel component. The pump may be used with both balanced and normal bypass valves. NBR, EPDM and VITON gaskets and mechanical seals ...

Power: 0 kW - 150 kW

... CENTRIFUGAL PUMP (NM) ASV Stubbe produces pumps for aggressive or corrosive liquids. We offer an extensive product range of horizontal or vertical pumps made of the most resistant materials – both related ...

Flow: 0 l/min - 100 l/min
Pressure: 10 bar
Head: 5 m - 50 m

... The NGM pumps are with one or two impellers. The two impeller pump can gain bigger flow rate. In fact they consist of two pumps connected in series, one is ejector- pump and the other ...

Flow: 3.4 m³/h - 227.1 m³/h
Pressure: 250 psi

... refrigeration pumps have been used successfully in a variety of applications including cold storage, food processing, refrigeration, ice production and turbine inlet cooling. Introduced more than 50 years ago, Cornell CB Series refrigerant ...

Flow: 0 l/h - 0.06 l/h

... to 1500 mL/hr (60 mL syringe) Pumps continuously until you stop the pump Infusion rate can be changed while pumping Syringe purge mode Power failure mode allows pump to continue pumping ...

Flow: 0 l/min - 18 l/min
Head: 0 m - 40 m
Power: 0.35, 0.25, 0.5 kW

... laboratory applications Advantages Suitable for the delivery of gas shares Steep characteristic curve High pressures with compact design ...