|
|
PL PUMPS
Fixed displacement
For open loop circuits
Up to 450 bar [6 530 PSI] pressure
Sizes 10 to 444 cm³/tr [0.63 to 27 cu.in/rev]
In line radial pistons
High speed for engine drive
High efficiency
High durability
Independent output flows
|
|
The F1 offers many additional values for operators of cargo cranes, hook loaders, skip loaders, forest cranes and heavy duty demanding truck applications.
Higher selfpriming speeds
Operating pressures to 400 bar
New frame sizes to meet market requirements
Higher overall efficiency
Increased reliability
Reduced noise level
Smaller installation dimensions
Series F2 is a further development of the twin-flow version of Series F1, the very first bent-axis truck pump on the market with two entirely independent flows. Typical applications include large truck loaders, forestry cranes, hook loaders, refuse collecting vehicles, concrete mixers and tipper/crane combinations.
Less energy consumption
Reduced risk of system overheating
Lower weight
Smart system solution means easier installation
High overall system efficiency
|
|
Gear pumps and motors made of cast iron in two pieces.
A rigid and compact structure that makes it possible to incorporate a number of functions in a limited space.
Wide range of displacements: from 0.30 in³/rev (4,95 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30 and 40
Max. peak pressure up to 4785 psi (330 bar)
Max. speed up to 4000 min-1
High operating pressures
High efficiency at high temperature
Low noise emission
Exceptional working life expectancy
Solid and compact design
Custom design
|
|
G4 Standard Electric is Powered by a 115V - 60HZ, 1-1/2 hp induction motor (1,725 rpm); low startup voltage, draws 16 amps at full load (230V models available).
G4 Gas pump is powered by a 4 hp Briggs & Stratton gas motor.
Electric models are equipped with a 15’ remote power controlled pendant.
Reservoirs available in 1.5-20 gallons; welded steel designs.
Recommended for mid-sized or multi-tool operation - 55 cu.in. flow group
Ideal for remote service application or in-plant production applications requiring quiet – continuous cycling
|
|
The quality, expertise and experience to deliver to your precise requirements.
Hydrokraft piston pumps and motors are renowned worldwide for their robustness and reliability. Hydrokraft offers a complete range of open and closed circuit pumps and motors available in fixed and variable inline design from 66 - 750 cm3 per revolution. Larger displacements can be achieved using combinations of our pumps and motors.
Hydrokraft manufactures high-pressure axial piston hydraulic pumps, motors and transmissions for applications in stationary industrial equipment, marine, mining, chemical processing, primary metals and other markets in open circuit or closed circuit applications.
|
|
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has shown the K3VG to be a market leader.
The K3VG unit has been developed specifically for the industrial market where noise, efficiency, controllability, extended pump life and reliability are considered essential.
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
The present K3V is designed specifically for the earth moving and construction industries where in excess of 700,000 units have been supplied.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has enabled the K3V to be a clear market leader.
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
Features:
Volumetric efficiency is over 95% and overall efficiency is more than 90% at
1800 r/min.
High performance at maximum pressure 35MPa
A3H series are compact in size becauseoutput / mass ratio is large.
|
|
DVQ-25 DURABLE DESIGNED HIGH PRESSURE PUMP
The maximum pressue:250 bar
Displacement:18/22/26/32/38/43/47/52/52/60/65/75
Aplication:
Shoes making machine, Plastic and rubber molding mahcine,
press brake machine, press shear and steel sheet forming machine.
|
|
With its new PRO high-pressure range, KMT Waterjet Systems sets new standards in the field of waterjet cutting. PRO stands for waterjet cutting technology with operating pressures of up to 6200 bar. The new range of products includes of course all necessary components and accessories - from high-pressure generation units to orifices that guide the cutting jet with great precision onto the material. The maximum pressure of 6200 bar represents an increase of nearly 50% over pressures used in conventional equipment!
The advantages offered by this leap in technology are obvious:
- Higher cutting speeds
- Improved cutting edge quality
- Lower abrasive consumption
|
|
|
|
|
|
HS
Grundfos HS end-suction pumps combine compact design, economical cost and simple maintenance to provide high-efficiency performance in a wide variety of applications. And because they include the pump end, motor adaptor and standard NEMA motor, Grundfos end-suction pumps install easily with no baseplates, bearing frames, couplings or guards.
FEATURES
* Ideal for water supply, irrigation, commercial and industrial uses
* Cast iron and brass contruction
* Capacity ranges to 175 GPM and 160 feet of head at up to 7.5 horsepower
* 60 Hz models available in all voltages, with 2 and 4 pole and specified enclosure classes available
* Optional MLE variable-frequency drive motor offers maximum efficiency and energy savings
* Buna-N O-rings as standard with carbon/ceramic shaft seal
APPLICATIONS
The Grundfos HS range of compact horizontal, centrifugal pumps are designed for small domestic and industrial water supply systems.
Applications include
* Liquid transfer
* Transfer and circulation of liquids within light industry and farming.
* Pressure boosting
* Domestic water supply
* Water Fountains
* Cooling systems
* Air-conditioning systems
* Light irrigation
* In addition, the HS is suitable for incorporation in specialized OEM equipment
|
|
Feature:
Max. Pressure:245 kgf/cm2
Max. Speed :1800 RPM Min. Speed: 600 RPM
Application: Hydraulic press machine, fishing boat,
lift truck, plastic injection machine.
For detail product dimensions, performance characterisitics and order code, please visit our web site:www.kcl.com.tw
|
|
Serie L - Aluminium body
Pumps
Motors
Flow dividers
Gear Pumps and Motors >> Serie G - Cast iron body
Pumps
Motors
|
|
Rated to 3000 psi. Spline or keyed shafts, side or rear porting, dual rotation available on standard models. Pressure balanced loading plates on either side of gears for maximum efficiency.
|
|
Construction
- Close-coupled gear pumps (rotary pumps).
- Pump casing with suction and delivery connections with the same diameter and on the same axis (in-line execution).
Applications
-For fuel oil and liquids with lubricating properties.
|
|
Hydraulic Gear Pumps
- For truck applications
- From 16 c.c./rev To 80 c.c./rev
- Pressure up to 325 bar
|
|
|
Gear pumps with heavy duty body, side and rear ports. Double support by taper roller bearings on the shaft.
|
|
High capacity gear pumps
1 SPA ** / 2 SPA ** / 3 SPA **
• Displacement from 0,9 up to 61,1 cm3/rev.
• Working pressures up to 270 bar
4 ISP **
• Displacement from 60,3 up to 120 cm3/rev.
• Working pressures up to 190 bar
|
|
* Chemical gear pumps GX series
Internal gear pumps incorporating fine ceramic gears
Max. discharge capacity: 35.2/42.5 L/min
Max. discharge pressure: 1.0 MPa
Main materials: SUS316, SiC, PTFE
* Chemical gear pumps GM series
Magnetic drive sealless type internal gear pumps
Max. discharge capacity: 35.2/42.5 L/min
Max. discharge pressure: 0.7 MPa
Main materials: SUS316, SiC, PTFE
* Chemical gear pumps GM-J series
Exclusively designed for sodium hypochlorite
Max. discharge capacity: 20 L/min
Max. discharge pressure: 0.5 MPa
Main materials: PVC, SiC, CFRETFE, PPS
* Magnetic drive gear pumps MDG series
Compact gear pumps that completely eliminate leakage problems
Max. discharge capacity: 14/17 L/min
Max. discharge pressure: 0.6 MPa
Main materials: SUS316, CFRPEEK, PPS
|
|
Leakage free, sealless structure
The pump mechanism is the magnetic drive type. Free of leakage trouble, the pump is suitable to be incorpotated in various equipment.
Superior corrosion resistance
The wetted parts are manufactured from superior corrosion-resistant materials such as stainless steel, PPS, and PEEK. Therefore, the pump can be used to transfer various types of chemical solutions.
Long life design
Each part that is precision processed using Iwaki's original technology excels in thermal resistance, therefore does not cause pump troubles due to thermal expansion of the parts. Even when operated for long continuous hours, the pump should exhibit superior durability.
|
|
|
|
|
|
The SP700 and VP700 are new battery powered backpack units weighing no more than 18KG providing hydraulic power for cutting tools, and other hydraulic equipment such as Jaws of Life® and hydraulic jacks as used by emergency services and in many other situations.
Jon Lye, Managing Director of GSF explains: “The uniqueness of the Interfron range definitely improves emergency operations; it’s an innovation in design and one we believe will make a dramatic difference to the industry.”
Indeed the range of battery powered backpacks are unique in the respect that it gives emergency crews complete freedom from petrol driven or vehicle mounted power supplies; no hydraulic extensions and no attachments mean no entanglements, which, in low visibility high risk environments, reduce accidents and increase access to enclosed and otherwise inaccessible spaces.
At the heart of the range is the SP700 and the VP700, both of which can be fitted with the appropriate hydraulic connectors, enabling the units to operate rescue tools from all major manufacturers, including: Holmatro, Amkus, Lukas, Zumro, Weber, TNT, Lancier, Nike Centaur, ResOtec and Enerpac. The units can be adjusted to use hydraulic pressure at 5100, 9200 and 10500 psi. Each unit has a total weight (approx) 18kg (40lbs).
This Interfron range represents a very exciting addition to GSF’s long established market leadership on high strength shock resistant telescopic slides, and our state of the art Promounts range of mounting gear, used to secure every type of gear and equipment onto emergency and defence vehicles.
- Jaws of Life® is a registered trademark of Hale Products, Inc.
|
|
Our piston pumps is delivers high efficiency and low mantenance under the toughest operating conditions.
* Reliable fast response mechanism
* Special shaped fluid port reduces nosie
* High strength cast iron housing
* Designed to handle a various application.
For more model, specs. dimensions, please viist our
web site:www.kcl.com.tw
|
|
SUNFAB SL
Dual-flow pump with displacement from 20/20 to 53/53.
also some differentiated flows.
Perfect for demanding hydraulic mobile applications, up to 330-350 Bar.
|
|
GEHO DHT
This GEHO DHT pump is an industrial design hydraulically driven piston pump capable of handling extremly viscous slurries, sludge and paste, both organic and mineral, on a 24/7 operational basis. These pumps have excellent suction capabilities, are designed to handle large objects and to minimize wear. The DHT pump range is developed and manufactured by Weir Minerals Netherlands b.v.
Features / Benefits
- capacities up to 100 m3/h
- pressures up to 120 bar
- high viscosities up to 100.000 cP (mPas)
- moderate to high abrasiveness
- mild corrosiveness
- up to 120 mm particle size
- up to 90% solids content
|
|
- For agricultural and truck applications
- Axial. From 20 c.c./rev to 110 c.c./rev
- Radial. From 11 c.c./rev to 96 c.c./rev
- Pressure up to 350 bar
|
|
|
|
|
|
PH pumps are robust, reliable piston grouting pumps, offering the possibility of computer piloting, with many improvements in safety and piloting.
Use
PH pump range is very large and allows covering the complete grouting range, from fine ground treatments to drilling injection. All pumps can grout loaded mud or great c/w slurry. PH 15 or PH 125 or PH 160 body can be directly mounted on drilling rigs. PH 2x5 and PH 15 can be mounted in one container, with integration of mixer and grout machines, eventually piloted by one computer for complete integration.
Versatility
The PH pump range is very easy to start and to maintain. All pumps are equipped with an automatic greasing unit. All pumps can be handled with a fork lift truck or with a crane. All pumps are equipped with a potentiometer in order to regulate the grouting flows.
Performance
The PH pump range has a large panel of grouting pressures (from 0 to 250 bar) and of flows (from 0 to 470 l/mn).
Safety
All PH pumps have been designed with automatic stop safety at the piston site, in case of opening.
|
|
Features
High efficiency
Under the conditions of pressure 16 MPa (2320 PSI) and speed 1800 r/min, the volumetric efficiency is over 98% and the overall efficiency is over 90%.
Low noise level
In the "A16" pump, the noise level is as low as 57.3 dB(A) [at the full cut-off pressure 21 MPa (3050 PSI) with speed 1500 r/min one metre (3.3 ft.) horizontally away from pump head cover.]
|
|
INDUSTRIAL PUMP
Leduc axial pumps are of the stationary cylinder block type. The inclined
swashplate is turned by the drive shaft, thus causing the alternate movement of the pistons. Fluid enters the pistons via a groove in the swashplate and is expelled via check valves, self–priming if required. The forces on the shaft are taken up by bearings. The pump body is made of forged steel.
A precise calculation of the stability of the films of fluid between the friction surfaces means that there is virtually no wear on the moving parts.
|
|
|
|
Hydraulic pumps
