Air nozzles

... Aerobell 168 offers a wide variety of bell cups and shape air rings that provide optimum performance and flexibility when coating anything from large panels to intricate shapes. MonoFlex shape air technology provides ...

Orifice diameter: 66, 40 mm
Flow: 0.83, 30 l/min
Pressure: 0.2, 1 bar

... a sintered nozzle (brass on U025, polyethylene on U060) has to be screwed onto a supplied steel nipple which previously has to be welded on the outside of the silo, bin or weigh hopper cone. Subsequently, connection with the compressed ...

Orifice diameter: 6.3 mm - 406 mm
Flow: 127 l/min - 1,614 l/min
Media temperature: 538 °C

... conveying

• Reduced compressed air consumption compared with open tubes
• Approx. 10 dBA average noise reduction (model-dependent)
• Improved

Orifice diameter: 0.64 mm
Flow: 495 l/min
Pressure: 5.5 bar

... Flat Super Air Nozzle Works
Compressed air enters the nozzle plenum and is directed through a precise slotted orifice. The primary airflow follows a flat surface creating a uniform ...

Orifice diameter: 0.64 mm
Flow: 1,039 l/min
Pressure: 5.5 bar

... li>Part ejection

• Lower compressed air costs
• Typical noise reduction of ~10 dBA
• Conserves compressed

Orifice diameter: 1.3 in - 4.3 in
Pressure: 0.5 bar - 10 bar

... GZS air steam flat fan tip is ideal for gas application. They are widely used in drying processes, water removal from surfaces, flocks and water blow off. ...

Flow: 5.5 l/h - 340 l/h
Pressure: 4, 3, 2, 0.7 bar

These single orifice set-ups produce a flat fan shaped atomized sprays.More precise details on the spray dimensions are given in the table on the right side of the page.The spray length can reach from 1.800 to 5.200 mm depending upon the set-up type and ...

Flow: 2.5 l/h - 93 l/h
Pressure: 0.7, 2, 3, 4 bar

These single orifice set-ups produce narrow-angle, full cone shaped, atomized sprays with a spray angle of about 20°.More precise details on the spray dimensions are given in the table on the right side of the page.The spray length can reach from 2.500 ...

... boron carbide, this abrasive blast nozzle offers chemical and wear resistance properties, making it ideal for abrasives such as garnet, aluminium oxide and steel grit to enter the nozzle. Boron Carbide Venturi Nozzle ...

Orifice diameter: 8, 6.35, 11, 9.5, 12.5 mm

... Double Venturi Blast Nozzle with Aluminium Jacket This abrasive blast nozzle offers a 35% larger blast pattern than a standard Venturi nozzle with only a small loss in abrasive velocity. Tungsten ...

Orifice diameter: 3.2, 4.8, 6.35, 8, 9.5 mm

... small parts, this abrasive blast (sandblast) nozzle features a tungsten carbide liner encased in an aluminium jacket, offering the greatest resistance to impact or flexing. Tungsten Carbide Straight Bore Nozzle (for ...

Flow: 2,200, 2,300 m³/h
Pressure: 2.5 bar
Media temperature: 60, 65 °C

... Coating Nozzle™ offers total control for demanding applications where control over a viscous media is required, including those in the pharmaceutical, food, and engineering industries. The VCN’s design allows the width of the spray, the ...

Flow: 0.46 l/min - 19.89 l/min
Pressure: 0.9 bar - 36.2 bar

... Dovetailed tip design for use with special threaded/welded bodies and caps, providing positive alignment. Available in flow sizes from 2 - 50 with spray angles of 0, 25, 40, 50, 65, 80, 90°. Orifice is offset 5° to axis of dovetail plus ...

Flow: 11.3 l/min - 315 l/min
Pressure: 1.4 bar - 43.8 bar

... Spray Characteristics The Delavan AL air atomising series spray nozzles offer the user a wide variety of spray patterns, flow rates and atomisation. Unlike hydraulic or pressurized nozzles where the ...

... mm for air heaters, GRAND, Oval-G and Vento-G (Item no.: 4021) Nozzle 150 x 10 mm for air heaters, GRAND, Oval-G and Vento-G (Item no.: 4022) Nozzle ...

... Tubular nozzles Nozzle 5 mm round (Item no.: 4000) Nozzle 5 mm round 150 mm length (Item no.: 4000.V) Nozzle 15 mm round (Item no.: 4005) Nozzle M 10 / Adapter ...

... Our speed welding nozzles and tacking nozzles in a variety of sizes for processing plastic welding wire; can be slid onto a 5mm tubular nozzle or screwed onto an M10 nozzle adapter. Speed ...

Orifice diameter: 10 mm
Flow: 3.4 m³/h - 59.5 m³/h
Pressure: 80 psi - 100 psi

... and More Cold Air Guns use vortex tube technology and filtered compressed air to produce sub-freezing air as low as -30 deg F (-34 deg C) for numerous industrial spot cooling applications. ...

Flow: 6.8 m³/h
Pressure: 80 psi - 100 psi
Media temperature: 21 °C

... is limited. The Mini Cold Air Gun uses only 8 SCFM of compressed air and produces temperatures as low as 0 deg F. The Mini Cold Air Gun is available with a single nozzle ...

Orifice diameter: 20 µm - 60 µm

... entrained by high velocity compressed air to create a range of micron-level spray droplets, resulting in greater surface coverage than conventional nozzles. With this more efficient use of the liquid, ...

Orifice diameter: 0.13 mm - 1.4 mm
Flow: 0.1 l/min - 11 l/min

... Exitflex, is an air assisted airless tips that integrates high-quality tungsten carbide inserts. It is capable of providing optimum erosion resistance in all situations. Even though it has a robust design this product ...

Orifice diameter: 0.13 mm - 1.4 mm
Flow: 0.1 l/min - 11 l/min

... Exitflex, is an air assisted airless tips that integrates high-quality tungsten carbide inserts. It is capable of providing optimum erosion resistance in all situations. Even though it has a robust design this product ...

Orifice diameter: 0.13 mm - 1.4 mm
Flow: 0.1 l/min - 11 l/min

... Exitflex tip for EcoGun, Optima 2100 Wi Optima 2100 and Trilogy AAA Super Finish 63-589 (TC preorifice) ...

Pressure: 7 bar
Media temperature: 0 °C - 55 °C

... emitter points of the HE air nozzle is current limited. Being installed outside the air flow, the high-voltage points are hardly subject to fouling, if at all. The single point nozzle ...

... ionizing air nozzle is used to clean and neutralize electrostatically charged surfaces. The use of compressed air allows awkward places to be neutralized and cleaned as well. Connected ...

Pressure: 6 bar
Media temperature: 0 °C - 55 °C

... This nozzle has been designed especially for neutralising and cleaning (small) bottles on the inside, etc. Ionisation takes place at the end of the tube from which the air is blown. The high-voltage point is not shockless. ...

Orifice diameter: 5 mm

Orifice diameter: 7.5 mm

Flow: 190 l/min - 575 l/min
Pressure: 0 bar - 8 bar

... amplifies the surrounding air, providing exceptional energy efficiency while significantly reducing compressed air consumption. Main features : - Coanda Effect : amplifies the airflow several times compared ...

Orifice diameter: 9.5 mm
Flow: 140 l/min - 490 l/min
Pressure: 0 bar - 8 bar

... and Air Amplification The Adjustable Transvector Jet TV-R series is an innovative solution for industrial blowing, suction, cooling and air amplification. Designed to deliver an airflow amplification ratio up to 25:1, ...

... suspended in a gas or on a surface, without the addition of air or external gas. This technology is used for many applications: defoaming, particles agglomeration, inert blowing… No air supply • No contamination • ...

Orifice diameter: 0.25 in

... capacity hollow cone spray nozzle with the finest atomization among hydraulic nozzles. • Capable of generating extremely fine spray. • Minimal clogging with free passage diameter 1.3–2.6 times bigger than that of conventional ...

Orifice diameter: 0.8, 1, 2 mm

... New TAIFUJet® series, Air booster nozzles, Compact, Shorter body (35mm long) compared to the conventional TAIFUJet 42mm wide type with the same performance. Features - This compact air nozzle ...

Orifice diameter: 2, 1, 0.8 mm

... Minimal Air Consumption saves on Air cost • Taking in surrounding air and boosts multiplied air flow. • Uniform distribution resulting from the unique flat design. • Low Noise Level, ...

Flow: 54 l/min
Pressure: 3 bar - 6 bar
Media temperature: -25 °C - 80 °C

... well-metered quantities. The fluid is properly and economically fed into the centre of the air stream. With the air and fluid choke (see picture) the amount of air and fluid is finely adjustable. Containers, ...

Flow: 60 l/min
Pressure: 3 bar - 6 bar
Media temperature: -25 °C - 80 °C

... in reference to air and fluid connection. How it works: The fluid hose is either laid into a pressure-free tank or connected. The atomizer should always be fixed a little above the maximum fluid level in the tank. With compressed ...

Flow: 54 l/min
Pressure: 3 bar - 8 bar
Media temperature: -25 °C - 80 °C

... °C: ISOVG150 - - 2.1 ml at 5 bar compressed air - - 1.9 ml at 3 bar compressed air - - Water - - 62 ml at 6 bar compressed air - - 48 ...

Orifice diameter: 3 mm - 10 mm

Venturi type, flanged, tungsten carbide with external aluminium cover, for small and medium productions

Orifice diameter: 5.5 mm - 12.5 mm
Flow: 850 l/min - 9,700 l/min

... Venturi type, threaded, tungsten carbide with external aluminium and polyurethane cover, for large productions Venturi type, threaded, boron carbide with external aluminium and polyurethane cover, for large productions ...

Orifice diameter: 6.5 mm

... boron carbide ∅ 6.5 mm banana type, threaded, tungsten carbide ∅ 6.5 mm ...

... supply by means of a high-tension cable and to compressed air via a common 6 mm air hose. We recommend the use of an air filter in such a way as to prevent the nozzle ...

... The nozzle entrains the surrounding air and creates a concentrated air stream, making it more economical. The nozzle is also very quiet. Like other active anti-static equipment, also ...

... of a high-tension cable and to compressed air via thread G1/8” and an air hose. We recommend the use of a 5 micron or smaller air filter in such a way as to prevent the nozzle ...

... . This counterflow sprayer nozzle can distribute the water uniformly into the cooling tower fill and non-clogging. Counterflow Sprayer Nozzle Counterflow cooling Towers Sprayer is an efficient, non-clogging nozzle ...

... tower nozzles are high-temperature resistant and have a non-clogging design. This three splash nozzle is made by the PP and ABS material, it is widely used in the counterflow cooling tower nozzle. Advantages ...

Orifice diameter: 30, 38 mm
Flow: 10 l/min

... This Cooling Tower ABS Spray Nozzle is one of three-splashed nozzles, which are made from ABS material. This spray nozzle is made by disposable injection molding, so it is suitable for the hydraulic ...