Other welding and soldering equipment

After many years of faithful service, it was time for the “36X” range to evolve to take into account feedback gathered from users from all over the world. >An all-new design to maintain user satisfaction: the Express design team has ...

After many years of faithful service, it was time for the "36X" range to evolve to take into account feedback gathered from users from all over the world. An all-new design to maintain user satisfaction: the Express design team has made ...

The Burner 4722 introduced by EXPRESS is ideally designed for copper pipe brazing, heating, conditioning, and sanitation areas. It features a 16-22 mm copper tube length with a 2,9 - 9900 BTU at 4 bar power rate and a flow level of 214 ...

Current: 5 A - 1,000 A

- The DC1013-T and DC613-T are high-performance 1000 amp precision Linear DC spot welding power supplies that combine touch-panel integrated database process control and monitoring with a high-accuracy, zero-ripple linear transistor ...

Laser Weld Monitor MM-L300A The monitor detects welding defects and errors such as gaps between parts, missing parts, weld depth over-penetration, incorrect focus point and cover gas absence. It provides feedback to operators on the ...

High Frequency Inverter Spot Welding Power Supply - HF27, HF25 The controls found on the HF25 series closed loop welders address the challenges of micro joining. Miniature welds are highly sensitive to small heat profile fluctuations ...

The 4400 is the most accurate and reliable monitor available for dust and opacity measurements in combustion applications not requiring automatic calibration checks. Optimised for multi-process plants, 4400 delivers you immediate performance ...

Designed specifically to provide the unique but vital measurement of sulphuric acid dewpoint temperature, the portable Lancom 200 supports boiler efficiency checks, corrosion protection and the management of high-cost fuel additives. Easy-to-use ...

4650-PM provides the stable, accurate low-range measurement of particulate matter in stacks and ducts where water droplets are not present in the flue gas. Consisting of a stack-mounted probe and separate control unit, 4650-PM’s forward ...

Width: 28, 45, 80 cm

Silicone pressure rollers from our own production Pressure roller 28 mm 1 axle ball-bearing mounted (Item no. 6994) Pressure roller 45 mm 1 axle 45° ball-bearing mounted (Item no. 6995) Pressure roller 80 mm ball-bearing mounted ...

Pressure roller convex 30 mm for inside corners, roofing, heavy-duty tarpaulins (Item no.: 6993)

Width: 7, 9 mm

Customs seal pressure rollers from our own production Customs seal pressure roller 7 mm (Item no.: 7007) Customs seal pressure roller 9 mm (Item no.: 7009)

A2 welding controller (PEI) is the control system for ESAB A2 tractors and A2 welding heads. The controller is connected to the power source by a control cable and can be connected to ESAB LAF 631 and LAF 1251.

ESAB has been developing robot welding equipment in cooperation with ABB since the beginning of the 80s. The introduction of the Arcitec software at the end of the 90s supported an efficient communication between the robot control ...

Lift height: 5,445, 6,445 mm

The Column & Boom CaB 44, 55, 66 and 77 is purposely designed and robustly built to withstand the rugged environment in the welding industry. • A smooth 360-degree locable rotation. • All vertical and horizontal guidings are precisely ...

Easy Touch Control ETC5000 Easy Touch Control ETC5000 is the plug + play basis for a complete format adjustment system. The intuitively operated control systems of ETC5000 is designed to control up to 31 bus-compatible position indicators ...

Technical characteristics - Single phase network with earth - Supply voltage: 110 to 230 V +/-15% - Input current consumed 23A at 230V and 32A at 110V - Frequency: 50/60Hz - Second gas line as an option & - Wifi antenna as an ...

Current: 32, 25 A

Technical characteristics - Single phase network with earth - Supply voltage: 110 to 230 V +/-15% - Input current consumed 25A at 230V and 32A at 110V - Frequency: 50 / 60Hz - Wifi antenna as an option: remote control of the screen ...

Current: 24 A

Technical characteristics - Three phase main with earth - Supply voltage : 400 V +/-15% - Maximum current on main : 24A - Frequency : 50/60Hz - Wifi antenna as an option: remote control of the screen on smartphone or tablet via ...

The automation and supervision of SMI conveyors are controlled by the VLS (VaryLine System) PRO, an advanced hw/sw system designed by SMI and based on PROFIBUS field bus. The VLS PRO can control up to 121 inverter-equipped motors and ...

The volumetric dosing system with gravimetric calibrator. Using the DOSIMAX MC 30, the dosing process is executed in three steps: 1. Placing the dosing unit on the calibrator and entering the production values. 2. The calibration ...

This 2-way solenoid valve is pilot-acting. With a body constructed from stainless steel, and a stainless steel stem and viton diaphragms, its valves are normally closed (NC) and are internally piloted. The solenoid valve is ideal for ...

Parker Kittiwake's MHC Bearing Checker is an innovative hand-held device that provides engineers with the capability to quickly and accurately analyze bearing condition and lubrication state. Allows for up to 1000 measurements between charges.

HVAC Explosionproof Control Systems. The ExReg controller system has been designed for use in Ex areas for all gases, mists, vapours and dust. In combination with Ex-Max actuators it is a closed loop control system for volume flow ...

Control component packages are a part of any actuator / valve installation. Rotork has extensive experience in the design and assembly of all types of fluid power control systems to satisfy any customer requirement for on / off, modulating ...

Rotork has been providing critical components and safety systems to the rail industry for over 20 years. They range from a simple manual system to an advanced full automated control system. - Specialist freight rail wagon door systems - ...

The The Ultra-Trak™ 750 shows the user an early warning signs of Mechanical failure, Valve leakage, Flow disruption and rcing by detecting changes of ultrasonic amplitude. The UE Ultra-Trak™ 750 Features, Demodulated Output for Analysis, ...

Listen to the bearing, start lubricating and determine when to stop! The Ultraprobe® 201 Grease Caddy is uniquely designed to allow an operator to si­multaneously lubricate and monitor ultrasound levels to prevent over-lubrication. As ...

Manage your lubrication program with the Ultraprobe® 401 Digital Grease Caddy Pro and reduce bearing failure. The Ultraprobe 401 Digital Grease Caddy provides all the data you’ll need to optimize your lubrication program. Whichever ...

EQ RC18 Integrated Dispense System Low Pressure 0 - 0.7 bar The Integrated Dispense System is connected to an external pneumatic supply. It regulates the adjusted dispensing pressure and controls the dispensing during the selected ...

BONDERITE E-CO DMC These days creating added value involves more than just an excellent product profile. You also need a partner who understands your business and your products, and who can develop new production techniques, optimise ...

Be in touch with your filter Highlights The ControlPro is the new filter control system of Plymovent and designed with the user in mind. ControlPro can control your extraction system automatically. Description A filter system ...

Product Information Safe and easy dispensing of liquids from bottles without compromise The new Varispenser 2 and Varispenser 2x are the ideal choice for dispensing aliquots of liquid from supply and reagent bottles. Advanced sealing ...

Voltage: 230 V
Power: 1,600 W
Temperature: 40 °C - 700 °C

TRIAC ST by Leister is primarily used for welding and welding and plastic processing. While in the development, a planned option has been designed to do devoid of additional technical characteristics. Alternatively, it is recognized by ...

Voltage: 230 V
Power: 1,600 W
Temperature: 45 °C - 620 °C

With its durable and creative structure, TRIAC AT hot-air hand tool is constructed for on-site plastic welding and shrinking applications, taking every customer's demands into consideration. Combining advanced and ergonomic design with ...

Voltage: 230 V
Power: 3,400 W
Temperature: 40 °C - 650 °C

Electron ST is a great powerhouse among the hand tools of Leister. The equipment is designed to appear like the the models from the TRIAC range. It can provide with improved ergonomics and ability for working with better comfort. It is ...

Payload: 90 kg - 240 kg
Reach: 2,496 mm - 3,701 mm

The KR QUANTEC prime is geared towards providing the perfect balance between payload and reach. When it comes to spot welding, it is the market leader. The prime achieves outstanding cycle times due to its robustness and high acceleration ...

Payload: 3 kg
Reach: 541 mm

KUKA Ready Packs Your complete robot package consists of a robot, a controller, an operator control element and software – with a delivery time of 2-4 weeks. KUKA Ready Pack: Unbeatable advantages in a single package Delivery in a 2-4 ...

Payload: 8 kg - 26 kg
Reach: 1,612 cm - 2,013 cm

KUKA Ready Packs Your complete robot package consists of a robot, a controller, an operator control element and software – with a delivery time of 2-4 weeks. KUKA Ready Pack: Unbeatable advantages in a single package Delivery in a 2-4 ...

Filtration Group PiC 1500 Particle Monitor for continuous mon- itoring of the particle contamination of hydraulic fluids LEER Use as a mobile and stationary system for quick and simple determination of the cleanliness of fluids Simple ...

The Filtration Group MFS-05 dp filter controller reduces the number of cleaning cycles to a necessary minimum compared to the simple time control principle. It facilitates a longer cartridge service life, improved cleaned gas values, ...

The Filtration Group filter controller MFS-05 is an easy to operate time control. Characteristics Inexpensive, compact design Cleaning with electrically isolated contact Instant cleaning with test switch Remote signalling by two ...

Hose/cable length: 15 m

Temperature : 60 °C Construction : Epoxy-coated steel Pressure of hose reel : 20 bar Use : Welding, cutting out Fluid : Oxygen, Acetylene

Hose/cable length: 15 m

This hose reel, manufactured by Prevost, is equipped with ISOFLAM, twin rubber hoses, color identification and is ideally used for secure allocation of oxygen and acetylene. It has an epoxy-coated steel housing and a hose reel pressure ...