Direct-operated solenoid valves

DN: 1.5 mm - 2.5 mm
Voltage: 12 V - 380 V
Temperature: 0 °C - 60 °C

... requirements. The solenoid can be easily and quickly replaced without interfering with the pressurised part of the valve. On the same mechanical part different types of solenoids ...

DN: 0.8 mm - 1.3 mm
Voltage: 6 V - 24 V
Temperature: 0 °C - 50 °C

High chemical resistance in contact with fluids The media-separating solenoid valves Series KDV are designed to control critical fluids such as aggressive, high-purity or temperature-sensitive ...

DN: 0.6 mm - 1.6 mm
Voltage: 5 V - 24 V
Temperature: 0 °C - 50 °C

... such as portable oxygen concentrators or emergency lung ventilators. For applications that demand more robust performance levels, the KLE version has been designed to control higher pressures and flow rates than ...

Voltage: 24 V
Pressure: 150,000 Pa

For reliable control of the coolant flow: Bosch solenoid valves are designed with decades of experience in thermal, fluid and energy circuits. Due to their robustness and design optimized for volume flow, ...

Voltage: 12 V
Pressure: 150,000 Pa

For reliable control of the coolant flow: Bosch solenoid valves are designed with decades of experience in thermal, fluid and energy circuits. Due to their robustness and design optimized for volume flow, ...

Voltage: 24 V
Pressure: 150,000 Pa

For reliable control of the coolant flow: Bosch solenoid valves are designed with decades of experience in thermal, fluid and energy circuits. Due to their robustness and design optimized for volume flow, ...

DN: 1 mm - 6 mm
Voltage: 230, 24, 110 V
Temperature: -10 °C - 80 °C

... controlled solenoid valve operates without differential pressure up to 90 bar, even in closed media circuits. It is therefore perfect for high-pressure and dispensing applications. • Extensive pressure ...

DN: 0.25, 0.375, 0.5 in
Temperature: -5 °C - 60 °C
Pressure: 1 mbar - 1,500 mbar

... which is activated by an electric coil. The solenoid pilot valve shutter in NBR nitrile rubber or Vulkollan®, is an integral part of the actuator mobile core. Both the orifices of the ...

DN: 0.25, 0.35, 0.5, 0.125 in
Pressure: 0.5 mbar - 1,500 mbar

DN: 0.5, 1 in
Temperature: -5 °C - 60 °C
Pressure: 0.5 mbar - 1,500 mbar

... techniques and of the in-depth knowledge of our technicians. This series of solenoid valves is patented. The DDN solenoid valves are direct drive, ...

DN: 0.7 mm - 1.1 mm
Voltage: 12 V - 24 V
Temperature: -5 °C - 50 °C

The direct operated solenoid valve is the interface between pneumatic and electronic. In fact, it is actuated by an electrical signal and in turn gives ...

Voltage: 12, 24, 220, 230 V
Temperature: -10 °C - 140 °C
Pressure: 0 bar - 50 bar

PNEUMAX offer a vast range of solenoid valves in brass and stainless steel designed to control air, water, steam and all fluids that are compatible with the materials (body and seals) used in the range. ...

Temperature: -50 °C - 150 °C
Pressure: 12 bar

Stainless steel brand series have been engineered and developed to meet process automation and Oil & Gas severe service requirements, where material performances, product reliability and health and safety issues are critical elements. ...

DN: 1, 1.5, 0.6 mm
Voltage: 12, 24, 6 V
Temperature: 0 °C - 82 °C

2-Way Elec. Valve, N-C, In-Line Mount, Wire Leads, 6 VDC Additional Information Air Flow 0.6 scfm @ 100 PSI Connector Wire Leads Max PSI 0 - 105 PSI Medium Air, Gas Mount Standard Mount Ports 10-32 Thread Power ...

DN: 0.6, 1, 1.5 mm
Voltage: 6, 12, 24 V
Temperature: 0 °C - 65 °C

... ultra-low leak applications Specs: ------- Valve Type: 2-way bi-directional or 3-way normally-closed & universally ported Ports: Inlet and outlet through manifold + 3-Way: Exhaust through top of valve Operating ...

DN: 1.8, 1.3 mm
Voltage: 24, 12 V
Temperature: 0 °C - 55 °C

... flows with more stroke Specifications *********** Valve Type: 2-Way or 3-Way, Normally-Closed or Normally-Open, Fully-Ported (3-Way) Medium: Compatible Fluids (40 micron filter recommended) Air ...

DN: 10 mm
Voltage: 12 V
Temperature: 5 °C - 50 °C

PIT-10 solenoid valves are the latest development in modern pneumatic design, where the main trends focus on miniaturisation, enhanced performance, reduced power and reliability. Numerous ...

DN: 8 mm
Voltage: 12 V - 220 V
Temperature: -15 °C - 50 °C

• Possible assembly on single and multiple bases • Monostable manual actuation as standard • Assembly in any position • Operation with filtered lubricated or unlubricated • Maximum ambient temperature: 50®C • Low ...

DN: 15 mm
Voltage: 24 V - 220 V
Temperature: -10 °C - 50 °C

• Possible assembly on single and multiple bases • Monostable manual actuation as standard • Assembly in any position • Operation with filtered lubricated or unlubricated • Low power absorption Quantity per package: ...

DN: 10 mm
Voltage: 5 V - 24 V
Temperature: -40 °C - 49 °C

... 15 psig and power as low as 318 mW, genvi is the ideal candidate for high flow control solenoid valve applications flowing air or gas. The new genvi solenoid valves ...

DN: 7 mm
Voltage: 3 V - 24 V
Temperature: -40 °C - 49 °C

LHD Series valves are compact, 7 mm conventional control solenoid valves intended for medical and scientific applications flowing air or gas. Available ...

DN: 7 mm
Voltage: 3 V - 24 V
Temperature: -40 °C - 49 °C

LHL Series valves are compact, 7 mm magnetically latched control solenoid valves that feature ultra-low power consumption (as low as 5.5 mJ/switch), low noise, and flow rates as high ...

Voltage: 24 V
Temperature: -20 °C - 65 °C
Pressure: 3 bar - 10 bar

• Assists machine designers in complying with the European Machineries Directive • Can help existing machinery to comply with PUWER (Provision and Use of Work Equipment Regulations) • Controlled increase of downstream pressure on start ...

Voltage: 24 V
Temperature: -20 °C - 80 °C
Pressure: 3 bar - 10 bar

... Provision and Use of Work Equipment Regulations) Controlled increase of downstream pressure on start up Medium: - Compressed Air

DN: 3 mm
Voltage: 230, 24 V
Temperature: -25 °C - 80 °C

... from 0 bar upwards Short switching times Suited for fine vacuum 1,33·10-3 mbar Assembled oil and grease-free For a.c. solenoid systems with integrated rectifier (40 to 60 Hz)

DN: 5 mm
Voltage: 6 V
Temperature: 5 °C - 70 °C

2/2-way solenoid servo-controlled valve of DN 5 in bistable version, for the control of potable water. The valve is especially suitable for use in electronically controlled, battery ...

DN: 5 mm
Voltage: 4 V - 7 V
Temperature: 5 °C - 70 °C

... and tests by the customer. The design of a separate valve seat by the customer is not to apply, as otherwise is needed, if a pilot valve will solely be used. The rate of flow of the ...

DN: 7 mm
Voltage: 12 V - 240 V
Temperature: 5 °C - 90 °C

2/2-way solenoid valve of nominal diameter DN 7 for use with cold and heated potable water and physically and chemically similar media. The valve is servo-controlled and normally closed ...

DN: 10 mm
Voltage: 12, 230, 120, 24 V
Temperature: -20 °C - 100 °C

... -way solenoid valve has a completely plastic encapsulated coil. The armature is sealed by a bellows made of PTFE backed by an additional safety diaphragm. The valve body is available ...

DN: 2 mm
Voltage: 12 V - 230 V
Temperature: -20 °C - 100 °C

... -way solenoid valve has a completely plastic encapsulated coil. The armature is sealed by a bellows made of PTFE backed by an additional safety diaphragm. The valve body is available ...

DN: 2 mm
Voltage: 24 V - 230 V
Temperature: -10 °C - 50 °C

The GEMÜ 0326 Directly controlled 3/2-way pilot solenoid valve is designed for mounting to a compact aluminium rail as a valve battery for mounting in ...

DN: 1.8 mm - 6 mm
Voltage: 12 V - 24 V
Temperature: -10 °C - 80 °C

Application : Air, water, gas Size : 1/8", 1/4" Direct acting; 3/8"…2"Operated Working Pressure : 0…16 Bar (1/8", 1/4") / 0,5…16 Bar (3/8"...2" ) Core, Tube :Stainless Body : Brass Seal ...

DN: 0.375 in - 1 in
Voltage: 12 V - 230 V
Temperature: -10 °C - 80 °C

... series solenoid valves is direct operated and full body design. That is supply direct acting solenoid valve up to max ...

DN: 0.125 in - 2 in
Voltage: 12 V - 230 V
Temperature: -10 °C - 160 °C

The S4010 (Normally Close) , S4011 ( Normally Open ) Series features solenoid valves designed for applications in fuel oil, burners, etc. These valves are built with stainless steel ...

DN: 2 mm
Voltage: 12, 24 V
Pressure: -70,000 Pa - 300,000 Pa

Structure - Direct-acting diaphragm, 2 way NC No.of ports - 2（specified inlet and outlet） Body material - POM,PVDF,PTFE Diaphragm material - EPDM,FKM,FFKM Voltage - 12V/24V Flow rate - 6.8g/s(25℃，50KPa ，H2O） Power ...

DN: 2.4 mm
Voltage: 24 V
Pressure: 0 bar - 4.5 bar

... material - PPA diaphragm material - FKM Dimension - 40.5*23*65.4 No. of ports - 2 Power Consumption - 6.5W Structure - Direct acting piston type Voltage - / Flow Rate - 10L/min Main Features - 1. Small size, ...

DN: 1.5 mm
Voltage: 12, 24 V
Pressure: -70,000 Pa - 400,000 Pa

Structure - Rocker diaphragm type, 2 way NC No.of ports - 2（specified inlet and outlet） Body material - PEEK,PVDF Diaphragm material - EPDM,FKM,FFKM Flow rate - 6.5g/s(25℃，50KPa ，H2O） Power consumption - 3.5W Main features - 1.Large ...

DN: 0.125, 0.25 in
Temperature: -10 °C - 140 °C
Pressure: 0 bar - 40 bar

Component Parts and Materials 1 Body: Brass 2 Seals: NBR - EPDM - FKM 3 Welded armature tube: Stainless steel 4 Fixed and mobile core: Stainless steel 5 Springs: Stainless steel Operator diameter 10 mm

DN: 0.25, 0.125 in
Temperature: -10 °C - 140 °C
Pressure: 0 bar - 18 bar

Component Parts and Materials 1 Body: Brass 2 Seals: NBR - EPDM - FKM 3 Armature tube: Brass 4 Mobile core: Stainless steel 5 Springs: Stainless steel Maximum allowable pressure 40 bar Operator diameter 10 mm

DN: 0.125, 0.25 in
Temperature: -10 °C - 140 °C
Pressure: 0 bar - 13.5 bar

Component Parts and Materials 1 Body: Brass 2 Seals: NBR - EPDM - FKM 3 Welded armature tube: Stainless steel 4 Fixed and mobile core: Stainless steel 5 Springs: Stainless steel Room temperature with coil class H - 10 °C + 80 ...

DN: 0.5 mm - 60 mm
Voltage: 6 V - 220 V
Temperature: -20 °C - 80 °C

We deal in 3 port Manifold Mounted valve Features: 15 mm Solenoid Valve. Manifold mounted. Compact design. Solenoid continuous duty rated. Lubrication not required. Model ...

DN: 1.2 mm - 5 mm
Voltage: 0 V - 240 V
Temperature: -20 °C - 80 °C

2 Way Direct Operated solenoid valve Direct operated solenoid valves are operated ...

DN: 1.2 mm - 1.6 mm
Voltage: 12 V
Temperature: -20 °C - 80 °C

Rotex 2 way direct operated High pressure solenoid valve We offer a range of proven high pressure solenoid valves intended for use ...

DN: 4 mm - 15 mm
Voltage: 24 V
Temperature: 0 °C - 50 °C

2/2 Way Solenoid valves straight passage type S1 and S2 PVC-U unionised body available with 2/2 way (versions S12 and S22) Installation and maintenance friendly design: high ciclying life ...

DN: 0.125 in
Voltage: 24 V - 230 V
Temperature: -10 °C - 130 °C

Internal parts: stainless steel Seals: NBR, EPDM, FPM, PTFE Ambient temperature: +55°C max Viscosity: 21 mm2/s max. Response time: 10 to 20 ms Duty cycle: continuous (ED100%) Cycling rate: 1000 cycles/min max Electrical protection: ...

DN: 0.25, 0.125 in
Voltage: 12 V - 230 V
Temperature: -10 °C - 130 °C

Internal parts: stainless steel Seals: NBR, EPDM, FPM, PTFE Ambient temperature: +55°C max Viscosity: 21 mm2/s max. Response time: 10 to 20 ms Duty cycle: continuous (ED100%) Cycling rate: 1000 cycles/min max Electrical protection: ...

DN: 0.25, 0.125 in
Voltage: 24 V - 230 V
Temperature: -10 °C - 130 °C

Internal parts: stainless steel Seals: NBR, EPDM, FPM, PTFE Viscosity: 21 mm2/s max. Response time: 10 to 20 ms Duty cycle: continuous (ED100%) Cycling rate: 1000 cycles/min max Electrical protection: IP65 (with plug to ISO 6952 ...

DN: 2.3, 0.8, 1.6 mm
Voltage: 24 V
Temperature: 0 °F - 149 °F

... -DP: All body ports are M5. • A-DG: G 1/8 male output port for mounting directly to suction cups, air cylinder, or the pilot port of a larger valve. Ports 1 and 3 are M5.