In-line valves

DN: 5.5 mm
Pressure: -1 bar - 40 bar
Temperature: -15 °C - 180 °C

... FEMALE RP ISO 7 - FEMALE RP ISO 7 VALVE The 66.000 serie is made of stainless steel AISI 316L function fittings: flow controls for cylineders, in-line and banjo fittings, unidirectional valve, quick exhaust valves, miniballvalves Ghinox. This line ...

DN: 20 mm - 32 mm
Pressure: 0.4 bar - 16 bar
Temperature: -40 °C - 200 °C

Just like the Hygienic safety valves, these overflow/control valves are also implemented in line with the construction features of hygienic design and confirmed in tests by the DGUV Committee for Foods and Luxury Items. Depending on the use and medium, ...

Pressure: 0 psi - 125 psi
Temperature: -29 °C - 149 °C

The Series 4000 Quick Opening Valve functions as in-line on-off switch particularly suited to applications in Instrumentation and Control Panels to open and close circuits or isolate gauges. The unique design of these valves permits full-closed to full-open ...

Pressure: 5,000, 3,000 psi
Temperature: 0 °F - 225 °F

... Use to slowly or quickly bleed pressure from a line after a calibration is complete • Easily connect between the end of a Quick-test hose and the process connection • Keep fluid or contaminates out of the hand pump, calibrator or nitrogen control ...

DN: 1 in
Pressure: 8.3 bar
Temperature: -55 °C - 71 °C

The GURU PC® freeze protection valve protects potable water-bearing systems that supply water for bathrooms and kitchenettes on passenger rail cars from freezing when the car heat is turned off for switching locomotives, during layovers, or a power outage. ...

DN: 1.5 in - 2.5 in
Pressure: 41.4 bar
Temperature: 400 °F

... The NIBCO® bronze ball valve provides bubble-tight shutoff at 600 PSI. The three-piece valve is ideal for hot/cold water, numerous gas applications, compressed air, vacuum service, condenser and chilled water. It may be used for isolation and throttling ...

DN: 0.375, 0.5, 0.75 in
Pressure: 0 bar - 34.5 bar
Temperature: -10 °C - 50 °C

... SMV stepping motor valve for high flow regulation of gases or liquids Design Features high precision two-way metering valves in aluminum unparalleled precision and resolution in controlling operate continuously without overheating; eliminates SMV ...

DN: 20 mm - 100 mm
Pressure: 3.5 bar - 6 bar
Temperature: 150 °C

The 10º vertical angle enhances drainability while minimizing the internal cavity within the tank. The welding pad of the body is conceived to be as compact as possible and flush welded to the vessel bottom, resulting as an integral part of the tank surface, ...

DN: 0.375 in
Pressure: 10,000 psi
Flow rate: 7 us gal/min

... Application: For systems using large cylinders or extended lengths of hydraulic hose. Operation: Controls surges by restricting flow if it exceeds 7 gpm. When flow subsides, valve reopens automatically. Has 3/8" NPTF male end to thread into return ...

... Somas are proud to announce a brand new product line in our range of butterfly valves in Fire safe design. The product line is called FSV (Fire Safe Valve) and is offered in wafer design, (FSVW), flanged design (FSVF), lugged design (FSVL) and with ...

DN: 50 mm - 600 mm
Pressure: 16, 10 bar
Temperature: 100 °C

Resilient-seated, lug-type butterfly valve for flange mounting to pipelines; disk with centric bearing; suitable for use in sea water applications. With replaceable liner mounted on a vulcanised seal carrier ring, and disk with triple bearing. Suitable ...

DN: 25 mm - 50 mm
Temperature: -100 °C - 300 °C

... Provide superior performance in abrasive environments, precise flow control and ease of maintenance, delivering operational reliability in the most challenging applications Vonk unique rotating disc choke valves have been designed for the upstream ...

Pressure: 240 bar

... DD and DM Valves are completely hydraulic in operation and will deliver either oil or grease. These Dualine valves are also fully and individually adjustable in regard to discharge quantity and are equipped with operational indicators. Each DD valve ...

DN: 10, 16 in
Pressure: 0.1 bar - 0.8 bar
Temperature: 1 °C - 42 °C

... Exclusive NSF Certified electronic control valves with proven piston, seal & spacer technology. Simple user-friendly, 2 line / 16 character LCD backlit display. Rotating ‘no touch’ diagnostics shows key data like date last regenerated, volume remaining, ...

DN: 0.25 in - 0.5 in
Pressure: 0 bar - 210 bar
Flow rate: 0 l/min - 55 l/min

... Variable Flow Control Valves maintain the flow rate of hydraulic fluid to a selected value. Applications include hydraulic cylinders requiring constant extension or retraction speeds and hydraulic motors requiring constant rotational speeds. When used ...

The All-Hydraulic ARV (ARV-H) can accommodate a wide range of tension and water depth scenarios — all with no required feedback for the position of the tensioner rod. That’s because the engineers behind the Olmsted valves provided by Oilgear developed ...

DN: 0.125, 0.25, 0.5, 0.75 in
Pressure: 0 psi - 125 psi
Temperature: -20 °F - 225 °F

Humphrey offers you a variety of air piloted valves within the unique construction of the classic Diaphragm-Poppet Series. Choose diaphragm-poppet valves for your difficult, critical applications when reliability and tight sealing are required. The lineup ...

... Product overview

• Name: Needle valve
• Model: GCT-02-31
• Brand: YUKEN
• Application: Die casting machine

• Model: GCT-02-31
• Function: Precision flow

DN: 100 mm - 1,400 mm
Pressure: 2.5 bar - 64 bar

The network has gained increasing importance trying to conciliate available water reserves and the always increasing request for water. Usually, the network capacity is always greater than the effective request; this implies the necessity to utilize devices ...

DN: 2 in - 40 in
Pressure: 0.6 MPa - 16.5 MPa
Temperature: -29 °C - 150 °C

... - Use electric actuators to drive them open and closed, power-to-open and power-to-close. - Electric valve actuators typically convert high speed low torque output motors into low speed high rotary torque output that drives the valve via a gearbox. - ...

DN: 50 mm - 800 mm

... GA30 Series valve contains a disc or gate that slides into the path of the flow to block the fluid path and out of the way of the flow to reopen the path. Gate Valve Prod Gate valves are typically used when a straight-line flow of fluid and minimum ...

The valve will allow flow from the higher pressure of port ① or ③ to the port ②. The valve is commonly used to direct oil from the pressure side of a bidirectional hydraulic motor to a pressure-released hydraulic brake.

DN: 0.5 in - 2 in
Pressure: 16 bar
Temperature: 0 °C - 100 °C

... Functional design for multi-unit installation Special brass spacer to protect the cylinder from incompatible fluids Colosing-against-flow type to avoid water-hammer Advantages • Compact design allowing install in reduced space plants • Versatile ...

Pressure: 15 bar - 300 bar
Temperature: -20 °C - 100 °C

... DPA PROGRESSIVE DIVIDERS LUBRICANT DISPENSING SEQUENCE The initial piston dispenses lubricant to the outlets corresponding to the final piston. The final piston dispenses lubricant to the outlets corresponding to the central piston or, if more than ...

DN: 8 mm - 200 mm
Pressure: 100, 16 bar
Temperature: -50 °C - 280 °C

... Vacuum resistance Design and manufacturing of our 2-piece and 3-piece ball valve allow a vacuum capability of at least 10-3 mbar (0,75 10-3 Torr). PED directive According to Pressure European Directive (PED) 97/23/ CE, all our ball valves are controlled ...

DN: 20 mm - 200 mm
Pressure: 10, 16 bar

... • Face to Face: IEC60534 • Flow feature: straight line, equal percentage, quick opening • Stem seal: bellows & packing seal, packing seal • Adjustable rate: 50:1 • Trim material: PFA, F46, PTFE • Designed standard: DIN En1349 (Conform: ...

DN: 0.125 in - 0.75 in
Pressure: 210 bar
Temperature: -20 °C - 100 °C

Double-acting flow control valves available from 1/8" to 3/4" bsp, max.working pressure 210 Bar, adjustable oil flow rate from 0,5 to 80 Lt./min. (depending on the size)

DN: 10 mm - 300 mm
Pressure: 40 bar
Temperature: -271 °C - -30 °C

... Series UNIVERS 1200 cryogenic - Globe, control or check valve and filter available - Suitable for medium temperatures from -271° C to -30° C (2K to 243K) - with adequate stem extension - For installation in vertical position or inclination of up to ...

DN: 3 in

The OPW 6500 series angle loading valve, made in cast aluminum, allows fluid to be held in the line out to the end of the loading arm. The aluminum body is constructed with stainless steel trim for a range of fluid handling capabilities. It has the “deadman” ...

Pressure: -1 bar - 10 bar
Temperature: -20 °C - 200 °C

... In-line Valves • Extracts a liquid sample from pipeline. • Installed on Horizontal or Vertical pipeline. • Sample is representative. • All wetted parts are made from corrosion resistant materials. Materials of Construction • 316L SS • Hastelloy ...

DN: 15 mm - 150 mm
Pressure: 16, 40, 50 bar
Temperature: -40 °C - 280 °C

... Fully lined or stainless steel Sampling Valves for safe and representative sampling of corrosive and aggressive process media from pipelines, pressurized or under vacuum. Gaseous samples can be provided by means of the Piston Injector. Main features • ...

DN: 0.25, 0.375, 0.563 in
Pressure: 30,000, 10,000, 20,000 psi

High Pressure Equipment Company has developed a complete line of valves and affiliated components specifically for the unique requirements of the oil and gas industry. We offer valves, fittings and tubing for use with sour oil and gas (H2S) . Our "SGS" ...

DN: 32 mm - 125 mm
Pressure: 0.7 bar - 16 bar
Temperature: -20 °C - 80 °C

... Our shut-off valves are designed primarily for incorporation in pump suction pipes and in the basic version have an SAE mounting face with connecting dimensions complying with SAE-Norm J518 - 3000 psi. The key feature: Thanks to clamping bolts inside ...

DN: 0.5 in - 4 in
Pressure: 1,000, 800, 600 psi
Temperature: -20 °F - 450 °F

... Size Range 1/2"~4" Working Pressure 1/2"-2" 1000PSI, 2-1/2"-3" 800PSI, 4" 600PSI W.O.G Temperature Range: -20 to 450°F END Type T-Clamp Options Padlocking Device Actuator Mountin Bracket Direct-Mounting ...

DN: 0.25 in
Pressure: 50, 110 psi
Temperature: 0 °F - 170 °F

... Material: Acetal Copolymer Colors: Orange, Black, Grey Compatibility: Yes: Acetone, Alcohol, Ethyl, Greases, Oils, Commercial Dish Detergents, Gasoline, Lacquer Solvents, Sodium Hydroxide No: Chlorine, Acids, Ammonium Hydroxide, Bases Strong, Hypochlorite ...

DN: 100 mm - 350 mm
Pressure: 5 bar
Temperature: 120 °C

... The HDPV2 Gate was originally developed to isolate silos in applications where high pressure aeration is used to fluidize powder discharge. Over time, the HDPV2 Gate has been redesigned and modified for greater application versatility. Ideal application: ...

DN: 25, 32, 40, 63 mm

... Our Eco Line gate valve is our gate valve in composite material with high strength and metal-like properties. The material technology and product design give the gate valve extremely long life and safe function. It is also lead-free and corrosion is ...

... Pneumatically Emergency Shut Down Valves SDV ESD Safety Instrumented System The VESON Emergency Shut Down Valves (ESDV, ESD, ESV, SDV) are used to isolate pressure and flow from a particular source during an overpressure situation or detection of a ...

DN: 0.5 in - 24 in
Pressure: 100 bar - 420 bar

... Pressure Seal Gate Valve Provider: Pressure Seal Bonnet Gate Valves, API 600, API 602, ASME B16.34, DIN 3202, 1/2-24 Inch, 600-2500 LB, PN100-PN420, Cast or Forged Steel. Med Pressure Seal Gate valves are intended for high pressure, high-temperature ...

DN: 1.5, 2, 3, 4 in
Flow rate: 5 m³/h - 150 m³/h

... This valve is operated by line pressure by means of a 3 way selector valve, this selector has the positions “open”, “close” and “auto”. In the “open” position the valve is fully opened, in the “close” position the valve closes slowly to avoid water hammer. ...