Liquid heaters

Power: 250 W - 8,000 W
Temperature: 350, 100 °C

Watlow’s new FLUENT in-line heater is a small, lightweight, high-performance heater that can replace both a traditional immersion type heater or a heater wrapped around ...

Temperature: 175, 400, 650, 870 °C

Watlow plate flanged heaters are easy to install and maintain. These flanged heater products are designed for heating heat transfer fluids, medium and lightweight oils and water ...

Power: 6 kW - 60 kW
Temperature: 1,020 °C

Watlow duct heaters are constructed of sturdy 0.430 in. (11 mm) diameter WATROD heating elements mounted to a 1⁄4 in. (6 mm) thick steel flange. These air duct heaters are easily adapted ...

Power: 0 kW - 750 kW

... immersion heaters are a fast and efficient way of heating up various liquid solutions in processing equipment, as well as in large tanks through the use of tank immersion heaters. ...

Power: 500 W - 6,000 W

... limit temperature probes to help protect your liquid and processes. Screw Plug industrial heaters from WATTCO™ are used for heating gases and liquids in tanks or vessels. ...

... stainless steel counterpart. Water circulation heaters use stainless steel because of its anti-corrosive qualities. In both applications, a pump flows the liquid, such as water ...

Power: 350, 700 W
Temperature: 80 °C

These types of contact heaters have been designed and manufactured for preheating and maintaining the oil temperature constant in air-cooled endothermic engines. They are in fact applied in contact under the oil sump. ...

Power: 80, 90 W
Temperature: 80 °C

These types of contact heaters have been designed and manufactured for preheating and maintaining the oil temperature constant in air-cooled endothermic engines. They are in fact applied in contact under the oil sump. ...

Power: 500 W - 15,000 W
Temperature: -10 °C - 80 °C

... passage of the device. We offer two types of immersion heaters: Our A-mounted immersion heater which is particularly suitable up to 6 kW. Standard configuration: Teflon® FEP insulated heating ...

Power: 1 kW - 15 kW

... , FEP or stainless steel frame Standard configuration : heating cable coated Teflon® FEP and metallic frame coated PP or PVDF. For use with feet at the bottom of the tank. Available for heaters with ...

Power: 1 kW - 15 kW

... With a PVDF or PP fixing bracket to secure the heater on the side. Recommended up to 6 kW. Assembly type B On metallic frame coated PP, PVDF, FEP or stainless steel frame Standard configuration : heating ...

Power: 2 kW - 24 kW
Temperature: 0 °C - 300 °C
Pressure: 0 bar - 15 bar

To heat water, fuel or oil circulating in pipework up to 15 bar max. These heaters are made of one or two DN 50 vessels in painted carbon steel, M45 screw plug immersion heaters, and a safety thermostat ...

Power: 2 kW - 238 kW
Temperature: 0 °C - 300 °C
Pressure: 0 bar - 15 bar

... circulating in pipework at 15 bar max. Consisting of 1, 2 or 4 DN 80 vessels, in painted carbon steel, M77 screw plug immersion heaters and a safety thermostat with automatic reset, set at 115°C for water and adjustable ...

Power: 0 kW - 75 kW
Temperature: 0 °C - 400 °C
Pressure: 0 bar - 25 bar

Screw plug heaters can be equipped with control and safety devices (thermostats, Pt100 sensor, thermocouples, etc.) for the measurement of the temperature in the fluid or of the heating elements. An ...

Power: 0 kW - 10,000 kW
Temperature: 340 °C
Pressure: 0 bar - 15 bar

Pirobloc designs, manufactures and installs customized suction heaters based on the needs of each customer and project. Our suction heaters are supplied with all nozzles for the thermal fluid inlet ...

... Alkaline cleaning solutions, Tars, Asphalt or air heating >> Stainless Steel - Corrosive liquids, food processing equipment, Radiant heating >> Incoloy - Cleaning and degreasing ...

... such that direct immersion heaters cannot be installed, portability is required, heaters are to be removed without emptying the tanks, or when there is no access to the liquid medium ...

Circulation heater is a combined unit of Electric heater bundle inserted inside a Pressure vessel or shell, in which fluid will be flowing continuously. It is a compact heating system ...

Power: 80 W
Temperature: 30 °C
Pressure: 0 bar - 100 bar

... electrical heating block, which is connected to an annexed temperature limiter additionally. Technical data Medium: all non-aggressive gases and liquids Nominal size: DN 8 Nominal voltage: 110÷265 ...

Power: 136 kW - 225 kW
Pressure: 250 Pa - 400 Pa

... flame control with photocell • Fan-Limit thermostat with automatic reset • Limit thermostat with manual reset • Fuel pre-heater • Two oil filters: oil pump filter and suction filter • Quick connector to external ...

Power: 111, 44, 20, 48 kW

Master direct oil heaters are highly efficient devices that provide large volumes of instant heat where it is required. They are best for open or well ventilated areas like factories, warehouses or construction sites. ...

Power: 21, 85 kW

MASTER BV 77 indirect oil heater Clean hot air Possible connection to an optional room thermostat Possible connection to a flexible tube Flue gas exhaust High air flow Electric control panel humidity and dust ...

... while heating enables pumps and stirrers to be easily employed. The Thermosafe is IP66 rated, so can be hosed down, even when operational, in complete safety. For more informations about the THERMOSAFE® Induction Heater ...

... immersion heater is made up of 3 or 6 tubular heating element sgenerally mounted in a circle, brazed or welded to a brass, steel or stainless steel screw plug. The watt density and the various type of ...

Circulation heaters are made of a steel or stainless steel vessel equipped with 3 nozzles (input-output) and with an immersion heater (generally threaded) equipped with space to add a control device temperature. The ...

Type : IECEX|ATEX Protection : II 2 GD, Exdb IIC T4 ~ T6 Gb, Extb IIIC T 80 ~ 130 ℃ Db IECEx : Explosion Proof Compressor Application : IHDC-SXXXXXX

Heaters with a bundle of tubular heating elements or cartridge type with withdrawable heating insets. Flameproof heater enclosure made of cast iron, carbon steel with ...

Power: 0 kW - 300 kW
Temperature: 900, 1,200 °C
Pressure: 16 bar - 100 bar

ELMESS flow heaters are used for heating liquids and gases. They are manufactured to customer specifications in explosion-protected design (ATEX, IECEx, etc.) or in high-quality industrial ...

... d or de IIB + H2 Heater for fluids type DHF..C.. Heater for gas type DHG..C.. Flameproof enclosure, welded type made of carbon steel or stainless steel, with built-in temperature limiter and monitor ...

Power: 13 kW - 65 kW
Temperature: 70 °C - 90 °C

Kroll's air heaters of the LH series are truly multi-talented in heat and air distribution - whether heating or ventilating, outdoor, mixed air or recirculation operation, multi-stage adaptation to ...

Power: 3 kW - 18 kW
Temperature: 60 °C

For heating small to medium-sized rooms, and as frost protection guards, the portable Kroll electric heaters are the ideal solution. The smaller models are also perfect supplementary heaters ...

Power: 2 kW - 8 kW
Temperature: 0 °C - 85 °C

Tubular immersion heaters (TIH) are used for heating water in the industrial sector. The heating elements must be completely covered with water during ...