DN: 10 mm - 80 mm
Pressure: 40 bar
Temperature: -30 °C - 200 °C
... Robust spring-loaded check valve type 4000 from Schubert & Salzer in seat cone design made of stainless steel with high flow rate for aggressive media and high operating temperatures. Size: ...
DN: 200 mm - 600 mm
Pressure: 0 bar - 0.5 bar
Temperature: -20 °C - 60 °C
... -return valve is an ATEX-certified safety device that prevents explosion propagation in duct systems. Installed between the filter and the plant, the internal flap mechanically closes during an explosion to isolate the affected area. ...
DN: 200 mm - 950 mm
Pressure: 0.5 bar
Temperature: -20 °C - 60 °C
... Geovent non-return valve is an ATEX-certified safety device designed to prevent explosion propagation in industrial duct systems. The internal flap closes mechanically during an explosion pressure wave to isolate the affected section. ...
DN: 47.63 mm
Pressure: 0 bar - 20.7 bar
Temperature: 0 °C - 71 °C
... Description
UNJ-thread straight-thru
check
valve in aluminum alloy for aviation fuel and hydrocarbon oil systems. Automatic, spring-loaded disk design with 1.875 in UNJ threads (12 TPI, right-hand) and 37° flared ...
DN: 0 mm - 10,000 mm
Pressure: -10 bar - 7,000,000 bar
... Overview
Emergency
Check
Valves (ECVs) are designed to block the spread of flames and gases, thereby preventing structural damage and protecting operators. The safety
non
return valve ...
Pressure: 450 bar - 4,200 bar
Temperature: -20 °C - 80 °C
... aforesaid valves allow not only to fill, but also to carry out the delivery under pressure with nominal diameters being double compared with the valves that are normally on the market for the pressure range up to 4200 ...
DN: 0.25 in - 1 in
Pressure: 0 bar - 1,500 bar
Temperature: -20 °C - 200 °C
... Duff-Norton Europe ball check valves for high or low pressure hydraulic circuits prevent flow reversal in a circuit or protect against overpressure that can occur in certain parts of a circuit. Unguided valves ...
Duff-Norton Europe
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 70 °C
... - Whitworth pipe thread - Thread G2 for manual override - Chambered O-ring - Sealing: NBR - Material: brass nickel plated, Al black anodized - Allowable medium: air - Temperature range 14 to 158 °F (-10 to +70 °C) - Working pressure ...
EISELE GmbH
DN: 80 mm - 2,000 mm
... CRC-CRR flap valves are non-return valves allowing water flow in one direction. Wall-mounted or flange-mounted, they ensure high sealing with EPDM gaskets and effective closure aided by counterweights. The CRC-CRR ...
... BALL CHECK VALVES Ball check valves VAP, with EN 12050-4 certification, are designed for use even with soiled liquids to provide full guarantees of operation in heavy-duty working conditions. ...
Zenit
DN: 1 in - 4 in
Pressure: 0 bar - 10 bar
Temperature: 0 °C - 130 °C
... These AWH non-return valves are engineered for use in pipe lines, systems and machines in the food and drink industry. Suitable for liquid products, additives and cleaning liquids. These valves prevent ...
DN: 0.25 in
Pressure: 0 bar - 30 bar
... This valve can be set from 0 till 30 BAR. It is used on the lubrication point. Key features: - Pressure: from 0 to 30 bar (adjustable) - Material: galvanized steel - Diameter port. 5 mm Elastomeric-plastic seal ...
DN: 4.5 mm - 10 mm
Pressure: 0 bar - 1 bar
Flow rate: 2.2 l/min
... Flex Check® products are high-performance miniature check valves that can be easily and safely pressed into bore holes. They are completely made of stainless steel and are available in ...
... 71504 Non-return valve, body made of brass with stainless steel filter. 3/4” BSP connection (F), diameter 47.5 mm - total height 91.5 mm. ...
DN: 0.5 in - 4 in
... plants, compressed air systems. They can be installed in any position: vertical, horizontal, oblique. Body in brass. Plate in stainless steel. Washer in NBR. Spring in stainless steel. Minimum and maximum working temperatures: ...
DN: 0 mm - 10,000 mm
Pressure: -10 bar - 7,000 bar
Temperature: -50 °C - 120 °C
... impair or interrupt
valve function.
The flap
valve allows nearly unobstructed passage of solids up to a defined size. Even long fibres are reliably transported through the pump head over multiple pump cycles without ...
DN: 0.25 in
Pressure: 300 bar
... We recommend Kytola's check valve model 2680A especially for the following applications liquid feed lines gas feed lines pressurised sealing water systems Main technical features of the Kytola 2680A check ...
Kytola Instruments Oy
... Clack automatic valves, the best technology of its kind available on the market. The introduction of the first Clack valve to the market at the beginning of this century revolutionized the concept of control valves ...
DN: 0.75, 1, 0.5 in
... Paani Precisions is one of the most renowned Brass Non Return Valve Manufacturers, Suppliers and Exporter. For manufacturing these components, we ensure that fine quality of brass metal is used. Further, ...
DN: 6 mm - 38 mm
Pressure: 250, 160, 100, 400 bar
... RHV-M-ED Check Valves RHV06ZLMEDA3C RHV08ZLMEDA3C RHV10ZLMEDA3C RHV12ZLMEDA3C RHV15ZLMEDA3C RHV18ZLMEDA3C RHV22ZLMEDA3C RHV28ZLMEDA3C RHV35ZLMEDA3C RHV42ZLMEDA3C RHV08ZLMEDA3C RHV10ZLMEDA3C RHV12ZLMEDA3C RHV14ZLMEDA3C RHV16ZLMEDA3C RHV20ZLMEDA3C RHV25ZLMEDA3C ...
WUXI SAMWAY CO.,LTD
DN: 3.175 mm - 19.05 mm
Pressure: 35 MPa
sanitary check valve
DN: 25 mm - 100 mm
Pressure: 10 bar
Temperature: 120 °C
... Food Grade Non Return Valve Stainless Steel SS304 Check Valve A check valve is a valve that prevents the fluid from ...
the best suppliers