Input voltage: 24 V
Output voltage: 4 V - 8 V
Current: 4 mA
... CRY575 MIC power is a three-channel microphone power module that provides a constant current source for the IEPE preamplifier, as well as the positive/negative power for the dual- power ...
Input voltage: 85 V - 265 V
Output voltage: 42.5 V
Current: 5.6 A
... When a power outlet is available near the CP120B or CP160B generators, a specific mains power supply can be used to directly power the generators without having to use the battery packs. ...
Input voltage: 230, 110 V
Output voltage: 5 V - 300 V
Current: 40 A
... system with a particularly powerful AC/DC source. EPOS MC4 is used to supply power to motors and trip coils and can be used as a battery substitute in switchgear and as a power supply ...
Input voltage: 230, 400 V
Output voltage: 300 V
Current: 40, 32, 30, 25, 20 A
... sources for single or three-phase voltages, with high power and fast settling time. •For powering resistive, inductive or capacitive loads •For testing components, motors and devices •Wide power range and precise ...
Input voltage: 100 V - 240 V
Output voltage: 24 V
... Power supply in card format (1 slot) for the audio matrix of the COMPACT and OPTIMAX2 systems. 100-240V AC input, 24V DC output. ...
Input voltage: 230 V
Output voltage: 24 V
Current: 0 A - 30 A
... emergency power supply according to EN 54-4 in case of power failure. The 19” unit (2u) is equipped with 6 fused outputs that can be used with up to 30 A load. The smart battery condition monitoring ensures ...
Input voltage: 12 V
Output voltage: 24 V
... Power supply with two 12 V DC & 5 Ah batteries for the uninterrupted supply of 24 V DC to the sets of mechanisms that are installed in accessible bathrooms and changing ...
... Switched-mode power supplies for top-hat rail mounting Version: Single-phase primary switched-mode power supply in metal housing. Note: Closed version with screw fittings with ...
Input voltage: 100 V - 240 V
Output voltage: 24, 48 V
Current: 20, 10 A
... immunity level 100% full load burn-in test 3 years warranty OVERVIEW NDR-480 is one economical slim 480W Din rail power supply series, adapt to be installed on TS-35/7.5 or TS-35/15 mounting rails. The body is ...
Lantech Communications Europe GmbH
Input voltage: 100 V - 240 V
Output voltage: 48, 24 V
Current: 5, 10 A
... immunity level 100% full load burn-in test 3 years warranty OVERVIEW NDR-240 is one economical slim 240W Din rail power supply series, adapt to be installed on TS-35/7.5 or TS-35/15 mounting rails. The body is ...
Lantech Communications Europe GmbH
Input voltage: 100 V - 240 V
Output voltage: 48, 24, 12 V
Current: 5, 10, 2.5 A
... immunity level 100% full load burn-in test 3 years warranty OVERVIEW NDR-120 is one economical slim 75W Din rail power supply series, adapt to be installed on TS-35/7.5 or TS-35/15 mounting rails. The body is ...
Lantech Communications Europe GmbH
... The PASF-60.24 is a two phase power supply unit with an integrated output-relay fit for the demanding solutions. It offers maximum functionality for applications in complex systems and machines. The power ...
Input voltage: 100 V - 370 V
Output voltage: 24 V
... /60.24 industrial power supplies are designed to provide stable DC voltage to a wide range of radio-electronic devices, such as relay-automation systems, controllers, etc. Maximum output power: ...
... DESCRIPTION The power hub combines reliable power supply, seamless fieldbus communication and wireless remote control in one powerful package. The power hub is a central ...
Output voltage: 180 V - 528 V
Power: 15,000 W - 900,000 W
... processes take place in electric machines in order to ensure defined machine cycles. The generated energy is often burned up by braking resistors. KEB’s power supply and regeneration ...
Input voltage: 0 V - 50 V
Output voltage: 15, 24 V
... instrumentation and thermal mass flow meters and mass flow controllers, announces the release of the THCD-401 four channel power supply, controller, and display which can be used to operate mass flow meters and controllers ...
Input voltage: 230 V
Output voltage: 48 V
... Low voltage uninterruptible power supply. Monitoring - 4 switched power lines - batteries - from the main power supply 4 configurable trigger inputs ...
Input voltage: 100 V - 240 V
Output voltage: 24 V
Power: 3 W
... The FTR power supply is a switching mode power supply to be connected directly to the line proviiding na isolated output. It is suitable for powering instruments such as 4-20 mA field ...
Input voltage: 90 V - 370 V
Output voltage: 24 V
Current: 3, 13, 5, 10 A
... The NOVUS NDR Power Supplies have full range voltage input, high efficiency, DIN rail support and operation temperature up to 50 ºC. Attending international standards and certifications they are a robust solution to provide ...
Input voltage: 100 V - 370 V
Output voltage: 24 V
Current: 2, 3.13, 5, 10, 20 A
... The NOVUS EDA Power Supplies have full range voltage input, high efficiency, DIN rail support and operation temperature up to 70 ºC. Attending international standards and certifications they are a robust solution to provide ...
Input voltage: 120 V - 227 V
Output frequency: 50, 60 Hz
... PS350XA5 power pack is the heart of the low voltage sensor system. It transforms 120, 240 or 277 volts to power the remote sensors. ...
Input voltage: 230, 115 V
Output voltage: 0 V - 60 V
Power: 800, 1,500, 4,500, 500, 3,000 W
... series of KONSTANTER power supplies provides you with top quality manual and remote controllable DC power supplies for laboratory and system use. Equipped with active power-factor ...
Input voltage: 115 V - 230 V
Output voltage: 24 V
Current: 1 A
... DES Series Power Supplies are specially designed for the full range of Magtrol’s Eddy-current and Powder brake dynamometers with the design goal providing the best response time. The DES Series supplies ...
Input voltage: 240, 120 V
Output voltage: 24 V
Current: 0 mA - 1,000 mA
... closed-loop power supply to provide smooth application of current throughout an entire range up to a maximum set point. By utilizing regulated current, fluctuations in brake torque caused by temperature changes within ...
Input voltage: 120, 240 V
Output voltage: 0 V - 90 V
Current: 0 mA - 1,500 mA
... unregulated power supply that is designed for use with Magtrol’s Hysteresis Brakes and Clutches. The 5200 is available in either 12, 24 or 90 VDC voltages, corresponding to the available hysteresis brake/clutch coil voltage ...
Input voltage: 380 V - 480 V
Output voltage: 48 V
Power: 1,500 W - 3,200 W
... Description
Industrial
power
supply designed for use with SOMANET and ACTILINK equipment. Provides 48 V
DC output with 1500 W continuous and 3200 W peak capacity. Integrated braking chopper ...
Input voltage: 342 V - 528 V
Output voltage: 48 V
Power: 960 W - 2,000 W
... : MPSU-960-48-MB
Input voltage: 100 V - 240 V
Output voltage: 24 V
Output frequency: 60, 50 Hz
... Power supply: – 100… 240 Vac (50/60 Hz) Connectable to: – Deltadue Series – Sigmadue Series – OPMT operator panels – 24 Vdc controllers and thermostats ...
Input voltage: 220 V
Output voltage: 24 V
Current: 5.2 A
... PSU-20 can reliably supply current in the area installed at plenty of flame detectors during rectification (at DC24V). • Reliably supply spare current • Supply current up to 20 flame detectors ...
Input voltage: 85 V - 370 V
Output voltage: 5 V
Current: 5 A
... Power supply, 5A, 5VDC, 85 to 264VAC Universal, DIN mount, Switching power supply FEATURES • Universal AC Input (85 to 264VAC) • DC Compatible Input (120 to 370VDC) • ...
Dataforth Corporation
Input voltage: 105, 125 V
Output voltage: 5 V
Current: 1 A
... encapsulated power supplies are available in 120VAC or 220VAC input voltage ranges and provide 5VDC outputs suitable for all SCM5B modules. They are designed to mount on the SCMXRK-002 metal rack or DIN-rail EN 50022- 35x7.5 ...
Dataforth Corporation
Input voltage: 85 V - 264 V
Output voltage: 24 V
Current: 5 A
... Power Supply, DIN Rail Mount, 85-264 VAC 47-63 Hz In, 24 VDC 5.0 A Out Dataforth’s PWR-PS5RxW series sets new standards for switching power supply technology. Combining rugged, compact ...
Dataforth Corporation
Input voltage: 115 V - 230 V
Output voltage: 24 V
Current: 40 mA
... Description: - Current loop power supply Power supply: - 115 / 230 Vac ± 10% 50 / 60 Hz Consumption: - 1,5 VA Stabilized output: - 24 Vdc 40 mA Operating temperature: - - 10 ...
SENECA | AUTOMATION INTERFACES
Input voltage: 24 V - 230 V
Output voltage: 24 V
Current: 50 mA
... Description: - Current loop dual power supply Power supply: - 115 / 230 Vac (s100s-1-ST); 24 V (s100s-3-ST) Consumption: - 3,5 VA Output: - 2-CH stabilized output with galvanic ...
SENECA | AUTOMATION INTERFACES
Input voltage: 115 V - 230 V
Output voltage: -15 V - 15 V
Current: 350, 75 mA
... Description: - Dual stabilized power supply Power supply: - 115 / 230 Vac ± 10%, 50-60 Hz Consumption: - 7,5 VA Output: - + 15 Vdc 350 mA; - 15 Vdc 75 mA Operating temperature: ...
SENECA | AUTOMATION INTERFACES
Input voltage: 230, 115 V
Output voltage: 18 V - 23 V
Current: 4 mA - 20 mA
... • Multiple power supply electronically up to four two-wire transmitters • Isolation of each circuit with each other protected against short circuits • Plastic housing for mounting on a 35 mm DIN-rail according to EN ...
Input voltage: 90 V - 264 V
Output voltage: 12 V
Several universal AC adapters / chargers for Mark-10 force gauge and torque gauges are available, each of which consists of a body and replaceable prong. Spare prongs are also available.
... The compact Q.PS-PEL-240x power units with 24 VDC output voltage can be installed in a very restricted space and therefore the installation in cost-effective electrical distributor boxes in accordance with DIN 43880 ...
Input voltage: 198 V - 242 V
Output voltage: 25 V - 250 V
Current: 15 A - 20 A
... Manufacturer: UHV
Power
Precautions
- Before operating the power supply with a high-voltage switch, carefully read the user manual to understand the operating methods
Input voltage: 220 V
Output voltage: 0 V - 420 V
Output frequency: 40 Hz - 65 Hz
... The UHV-930 precision program-controlled power supply is a programmable AC voltage and current source designed for inspection, calibration and production test applications. It provides low-distortion sinusoidal outputs ...
Output voltage: 0 kV - 50 kV
Current: 0 mA - 1 mA
Power: 50, 40 W
... • Voltage : 0-40 kV ; 0-50 kV • Current : 0.0-1.0 mA • Power : 40 W ; 50 W • Control : 3 inches touch screen • Safety : Automatically shut down when spark occur • Dimensions (LxWxH) : 300x400x150 mm3 • Weight : 5 kg ; 6 kg ...
the best suppliers