Stainless steel valves

DN: 8 mm - 80 mm
Pressure: 64 bar

... Investment casting, hexagon, reduced bore, with lever. Parallel BSP thread to DIN/ISO 228 Housing and ball made of 1.4408. Sealing material PTFE, for screw pin to DIN 3852 Part 2 Form A. We reserve the right to alter dimensions. ...

DN: 15 mm - 200 mm
Pressure: 4 bar - 16 bar
Temperature: 140, 110, 90 °C

... Butterfly valves/Leakage butterfly valves KIESELMANN butterfly valves are a space-saving solution for hygienic process plants. They are preferably applied for panels, for tank shut-off and as a ...

DN: 0.75, 0.5 in
Pressure: 150, 300 psi
Temperature: 358, 550 °F

... Control Four-V Port Globe Valves are equipped with a micrometer dial and pointer which enables the valve to set within 1/100th of a turn of the handwheel. This allows you to fine-tune the blowdown flow rate. In the event ...

DN: 50, 65, 80 mm
Pressure: 0.5 bar - 1.5 bar
Temperature: -20 °C - 80 °C

... The asa butterfly valve with SAE and DIN flange connections allows the combination with an elastic element (rubber compensator expansion joint) to make a short compensating and economical connection with the pump port. The lever position ...

... factors such as the flow conductance and leak-tightness of valves are of great importance. The valves of Leybold are optimized with regard to these demands. For every flange system there are a lot of valve ...

DN: 25 mm - 150 mm
Pressure: 0 bar - 10 bar

... Inexpensive shut-off fitting in the hygienic product and CIP section Solidly designed valve disk Safe guidance of the disk thanks to bushes in the housing Seal with a small volume and extension gaps for compensating temperature ...

DN: 8 mm - 50 mm
Pressure: 63 bar
Temperature: -25 °C - 180 °C

... industry, high temperature, high pressure PRESSURE PFA/PS in bar BODY : CF8M BALL : Stainless steel 316 ...

DN: 50 mm - 600 mm
Pressure: 1, 1.6 MPa
Temperature: 425, 80 °C

... Major Parts and Components Body and cover - Stainless Steel, -carbon steel Flashboard - Stainless steel, -carbon steel Stem - Stainless ...

DN: 25 mm - 400 mm
Pressure: 0 bar - 10 bar
Temperature: 220 °C

... Energy saving valve for the precise and economical control at low loss of pressure of liquids and gases that can be either clean or contain particles. Applications - Air for aeration in wastewater treatment plant - Gases - Municipal ...

DN: 0.25, 0.5 in
Pressure: 40 bar
Temperature: -40 °C - 100 °C

... powered mass flow meters red-y compact series. Tightly Closing Valves The valves are tight-closing Different Device Setups The valves are available as straight valves or valve ...

DN: 350 mm - 1,200 mm
Pressure: 10, 16 bar

... 304 Stainless steel bolts - 250μm epoxy coating Bi-directional sealing The backlash-free shaft is connected to the disc. It is never in contact with the fluid, protecting it from corrosion. Built-in sealing ...

DN: 0.25 in - 4 in
Pressure: 20, 10, 40, 30, 25 bar
Temperature: -10 °C - 120 °C

... according to the matenals list authorized by the 4 MS • - Full bore • - Anti blow-out stem • - Large fiat sealing face • - Stainless Steel bail from DN3/4* to 4" • - PTFE packing • - Fiat Steel ...

DN: 12 mm

... This is the LBS-PN 64 series of ball valves from FG Inox. It is engineered from an AISI 316 stainless steel and is made with a female threading type on both ends. The series comes in 8 variants that have ...

... lockup valve is open and allows the free flow of compressed air from the positioner to the pneumatic actuator. When the lockup valve loses its signal (or it drops below an adjustable set point), the lockup valve ...

DN: 25 mm - 150 mm

... The "Monopok" valve is a 1/4 turn ball valve shutoff, with full waterway, made of an aluminium alloy section heat-treated. The whole is machined on a computerised and automated machine tool, which guarantees a precision ...

Pressure: 0 bar - 150 bar

... QYF-2R sampling valve is used for calibration gas cylinder sampling. This valve could directly connected with cylinder and easy to opearate It is for corrosive gases: NH3, NO, H2S, SO2 Max input pressure:15MPa It ...

DN: 0.25 in - 3 in
Pressure: 0 bar - 63 bar
Temperature: -25 °C - 180 °C

... TECHNICAL INFORMATION1. Stainless steel full port ball valve, 2 pieces2. Thread ends according gas EN 10226-1 (EX ISO 7-1 e DIN 2999)3. Made of AISI 316 (CF8M)4. Ball seats PTFE + 15% G.F.5. Blow-out proof stem6. Viton ...

DN: 25 mm - 50 mm
Pressure: 16 bar

... coating (thick. 250µm), nontoxic. - Steel rod X20Cr13 - Threaded CW612N brass shutter and bushings - NBR or EPDM gaskets and sealing o-rings on request - Nuts, bolts and washers in galvanised steel or stainless ...

DN: 13 mm - 25 mm
Temperature: -20 °C - 100 °C

... series from Gemels is a stainless steel, two-way ball valve that is equipped with ball seats with a size range of DN13 to DN25. This valve operates under pressure up to PN210 and PN420, ...

DN: 15 mm - 200 mm
Pressure: 16, 25, 40 bar
Temperature: -10 °C - 180 °C

... lower values Body: Spheroidal cast iron GGG-40 EN-JS1024 Valve/shaft: CrNi steel 1.4057 / CrMo steel 1.4122 Stuffing box seal: EPDM, max. +180°C, up to 350°C with different seals, see valve ...

... For manually shutting off the compressed air supply to the barrel pump and activating the material pressure relief. FP015, FP045, FP050, FP050-T, FP200, FP200-T, FP200-S ...

DN: 19.05 mm - 203.2 mm

... solid stock and electropolished - Available in sizes 0.75″ to 8.0″ - 316L stainless steel - Elastomers in white silicone, EPDM, or Viton HIGHER FLOW CAPACITY Model #43 butterfly valves are designed to ...

DN: 50 mm - 600 mm
Pressure: 16, 10 bar

... characteristics are essential for gate valves. We have therefore incorporated our many years of experience into developing our E3 gate valves to give them the finishing "Made for Generations" touch. The result: Hawle ...

DN: 25, 15 mm
Pressure: 5 mbar - 4,000 mbar
Temperature: 130 °C

... Tank blanketing valves are commonly used in tank storage systems to prevent and protect against explosions (avoiding flammable liquids being vented from the vessel), to control product contamination against external air that may fill ...

DN: 0.375 in
Pressure: 0 bar - 8 bar
Temperature: 0 °C - 100 °C

... nickel-plated and stainless steel. The PEKI series “big” bore addresses the need of many users for more fl ow. The models are designed with 7,8 and 12 mm valve seat bores, which are commonly found ...