GHM amplifiers

Frequency: 50 Hz - 5,000 Hz

... Digital Accumeasure Gen 3 Our new capacitance amplifier converts the probe capacitance directly to target gap (distance). This direct conversion approach eliminates errors that traditional analog amplifiers ...

Voltage: 1 mV - 4.5 mV
Current: 4 mA - 20 mA

Housed in an IP50 in-line enclosure, Mantracourt’s In-Line Amplifier (ILA) converts strain gauge or load cell inputs into a high stability 4-20 mA output. Its small design enables it to be easily integrated into compact ...

Voltage: 100 V - 250 V
Current: 40 mA - 120 mA
Power: 3, 30 W

Bipolar Operation for Piezoelectric Patch Transducers • OEM module for piezoelectric DuraAct patch transducers • Compact: 87 mm × 50 mm × 21 mm

Voltage: 990 V
Current: 630 A
Power: 14, 28 W

Cost effective MRI Gradient Amplifier for 1.5T high field MRI systems Product features -Cost effective three-axis Gradient Amplifier cabinet -990V / ±630Apk / 230Arms -Immune to condensation ...

Current: 1.2 A - 9.7 A
Frequency: 8 GHz - 15 GHz

... to Point and SatCom Data Links - Ideal for Airborne & UAV Use - Compact Laboratory Amplifier - Radar Description The MPM is an efficient, low noise amplifier consisting of a high gain solid-state ...

Power: 0 W - 30 W

-Three Optical Amplifier C-Band applications: Booster amplifier Line amplifier Pre-amplifier -l Multiple operating modes: ...

Voltage: 12, 20 V

Amplifier for Simplebus 2 video systems. Regenerates the riser signal regarding the video component. Complete with microcontroller for optimum operation management. For its use, follow the indications given in the technical ...

The CS22A Frequency Shift Carrier Terminal from Trench Group are units that are ideally used for transfer trip relaying systems. It is suitable for providing protective services for breaker failure in either 1 or 2 channel applications. ...

Voltage: 20 mV - 4,000 mV
Current: 4 mA - 20 mA

The DR7 is a DIN rail mounting amplifier designed to install in suitable cabinets along with other similar devices. To reduce electrical noise, system problems and the risk of accidental damage the DR7 has full isolation ...

Current: 8 A
Power: 1,912 W

... control motor power separately from control logic power. The amplifiers are interfaced to a PMAC controller via ACC-24E2, ACC-24E2M, ACC-24E3 (Power PMAC only), ACC-8F or ACC-8FS. These drive amplifiers ...

Current: 0 mA - 0.02 mA

The MTI04 sensor signal amplifier is a four-channel resistive transimpedance amplifier that can be programmed for a total of eight levels. These levels include 25kΩ to 20MΩ, 25nA to 20μA and 6 to 300kH, ...

Frequency: 200 MHz

... , Very Low-Noise X-band Noise Amplifier with an integral isolator, for Radar Receiver applications. A novel in-line waveguide to microstrip transition is used to give an axial format to the input and output. The amplifier ...

The DCI-Eco is the latest member to its DCI product family. MPB’s DCI-Eco Optical Line System (OLS) is a complete DWDM line system for data center interconnect applications. It provides all of the optical grooming necessary for transmission ...

Voltage: 1.8 V

The PI2MEQX2503 provides two lanes and clock MIPI D-PHY ReDriver™ with regenerates the D-PHY signaling. The device complies with MIPI D-PHY1.2 standard and can be used in either a MIPI CSI-2 or MIPI DSI application at datarates of up ...

Current: 20 mA - 2,000 mA

AMP: ultra high speed high voltage amplifier AMP series is an ultra high speed high voltage amplifier. It realized as fast as 700 V/µs even with load, and approximately 2 times faster than existing models. ...

DP-300 Series amplifiers are AC/DC differential amplifiers highly suited for EEG, EKG and extracellular recording. Features include high input impedance, high common mode rejection [100 dB @ 60 Hz], low ...

Voltage: 50 V
Current: 750 mA
Power: 19 W

The Model 2348 2 MHz Power Amplifier has a continuous current output of 750 mA at voltages up to 50 Vp-p. This provides 18.75 W of AC or DC output power to 500 kHz. The instrument’s bandwidth ranges from DC to 2 MHz. An ...

Voltage: 380, 220 V
Current: 40, 30, 4, 3, 4.5 A
Power: 90 W - 3,300 W

The Power Amplifier is designed specifically for inductive (or capacitive) loads. It has the characteristics of low interference, good linearity, low distortion, high stability, and wide frequency range. It is very suitable ...

Voltage: 27 V
Current: 2.4 mA

Straingauge Amplifiers Single and multi-channel Straingauge Amplifiers with precise, low-noise standard analogue outputs, display and setpoints for industrial applications. These accelerometers ...

Voltage: 5 V
Current: 1.5 A
Power: 10 W

Size: 101.75*75*36.2mm - Trumpet: 2Ω 5W 2.5Inch magnetic trumpet Weight: 128g - Color: Black/White Battery Capacity: 1100mAh Working Temperature: -10~45℃ - Case Material: ABS+surface tanning Bluetooth Version: 5.0 - Output power: ...

Frequency: 1 Hz - 100 Hz

Measuring Amplifier For a wide range of high-precision acoustic measurements. * Supports connection of several microphones useable: UC-53A, UC-52, UC-34P, UC-29, UC-27, UC-31 with suitable preamplifiers and cables. * ...

Power: 3,000 W
Frequency: 10 kHz - 100,000 kHz

ETS-Lindgrens Model 8000-08 RF Power Amplifier is a 3000 W power amplifier, designed primarily for EMC applications that include MIL-STD 461 RS103, 200 V/m. Utilizing GaAs technology, this RF amplifier ...

Voltage: 230, 24, 100, 70 V
Current: 1.38 A
Power: 250 W

Class-D power amplifier, 230VAC and 24VDC, 100V, 70V or 8 Ohms • Class-D power amplifier in PWM technology for 70 V, 100 V or 4 Ohm loudspeakers • Properties better than IEC 268.3 • Automatic ...

Voltage: 220 V
Frequency: 50 Hz

The R-RF-10-RZ amplifier is a desktop amplifier explicitly designed for RZ code transmission in high-speed optical fiber communication systems. It amplifies tiny high-speed signal levels to a higher level ...

GLSUN OTS3000-EDFA Erbium Doped Fiber Amplifier is different from OEO and can directly amplify the signal of multi-wavelength from the C-band to effectively extend the transmission distance when the optical signal is ...