|
|
Nex Flow™ removes the confusion from air jets and nozzles. You do NOT need hundreds of different nozzles. All air amplifying nozzles produce air flows up to 25 times the compressed air consumed. Different nozzles have different outlet sizes and the more air used, the greater the force produced. Noise reduction u t 10 dBA is typil as well as reduced air consumption when compared to open jets and tubes.
The most important reason to use air nozzles or jets is safety All Nex Flow air nozzles and jets meet OSHA standard CFR 1910.242(b) for dead end pressure. Noise levels are dramatically lower with air nozzles and jets in addition to lower energy use.
|
|
Water jet cutting technology has asserted itself to an ever increasing degree against competing technologies. Highly wear resistant carbide nozzles are a major fact for the cutting result. The main areas of application are the automotive, packaging and aerospace industries, mechanical engineering and electronics.
Water jet cutting has a number of advantages:
- cutting takes place at room temperature (thermal stress is avoided)
- only one tool is used: the water jet
- no limits as to materials that can be cut: ranging from stone, composites, plastics, metals ... up to a thickness of 150 mm.
- a clean job: as opposed to thermal procedures, water jet cutting is emission-free
|
|
Lechler high-pressure solid stream nozzles
We have a wide range of special hardened stainless steel nozzles for high-pressure applications, with carbide metal inserts as an option.
High-pressure solid stream nozzles produce a closed, stable, powerful solid jet that does not break away, even at very high pressur
|
|
|
Lechler flat fan nozzles stand for uniform liquid and distribution. Particularly high energy jets are generated with spray angles up to 60°. Nozzles with small flow rates are especially suited for humidifying and spraying in general. The flow geometry of the nozzle allows to produce accurate, compact jets, available with different distribution patterns.
|
|
A wide variety of nozzles are available
for all types of drill bits and unique applications
requiring precise flow control.
|
|
Design:
- For multi-purpose torch systems
- For hand cutting torches
- Cutting range up to 500 mm
Advantages:
- Carefully selected materials guarantee high cutting quality and increased cutting output
- Perfectly matched combination of torches and nozzles enables most reliable operation
- Special surface protection ensures long service life
- All cutting nozzles individually tested for quality assurance
- Reliable arrangement of ducts and slots allows easy cleaning with special nozzle cleaning drills
Product Range:
- Ring-/slot cutting nozzles
- Block cutting nozzles
- Gas-mixing cutting nozzles
- Accessories
|
|
Whatever your application, whatever your fuel gas, there's a Smith SlicerTM tip to provide fast, economical and quality cutting. Soft seats are not prone to damage like metal-to-metal seats, providing consistent seating and much longer life than metal to metal seats.
FEATURE BENEFITS
1. In-Tip Mix Provides Added Resistance to Flashback
Each tip is a precision engineered mixer for combining preheat oxygen and fuel gas to attain maximum efficiency.
2. Slip-In Design Saves Time and Money
Quick, easy tip change encourages use of right tip for the job.
3. Hand Tighten Tips - No Wrench Needed!
After the first tightening with a wrench, all that's needed to seat the tip snugly is hand-tightening. No need to search for a wrench to change tips; threads on tip nut won't be stripped by over-tightening.
4. Soft Graf-Tite® Flexible Seats End Reseating Repairs
Compressible soft seats are practically indestructible and they withstand very high temperatures, resulting in longer tip life.
5. Fully Swaged Tip Minimizes Gas Turbulence
Mirror smooth gas passages deliver stable gas flows for high heat transfer, fast starts and clean cuts, also, minimizes slag build-up, and reduces clean-up time.
6. Concave Shaped Tip End
Reduces backfire and resists flameout when making accidental contact with base metal during cutting operations.
7. Removable High Pressure Seat
Allows cleaning from back of tip.
|
|
• Complete blower air knife systems engineered for horizontal or vertical conveyors
• Static control ionizing bars and vacuum recovery systems for debris also available
• Products are CE Registered with IEC Motors
• Eliminate expensive compressed air and reduce energy usage by 75%
• Sonic is an ISO 9001:2000 Registered company
• Most Blower/Motor assemblies shipped in 5 days from receipt of order
• Fill out the on-line questionnaire for a quote.
|
|
Silvent920 A
SILVENT 920 A: flat nozzle that generates a broad and efficient air cone. Outstanding for use wherever a wide but thin striking surface is required. Flat nozzles are suitable for most areas of application, such as: drying, transporting, cooling, cleaning etc. Often used in manifold systems, providing silent and highly efficient air knives. Made of zinc with 1/4" male connection thread. The exhaust ports are protected from external forces by fins. Fully complies with EU Machine Directive noise limitations and OSHA safety regulations. Patented.
|
|
SPRAY CHARACTERISTICS:
F-Series spray nozzles produce a flat, fan-shaped spray pattern, with spray angles available from 0° solid stream to 110° fans measured at 40 psi. Spray angles generally increase with pressure.
TYPICAL APPLICATIONS:
Suitable for a variety of washing and spraying applications.
- Parts Cleaning
- Metal Washing
- Foam Control
- Asphalt Spraying
- Gravel Washing
- Vehicle Washing
- Fertilizer Spraying
- Dishwashers
|
|
TYPICAL APPLICATIONS
Asphalt or tar laying, bottle washing, coal and gravel washing, degreasing, dishwashing, foam control, industrial washers, metal
cleaning-rinsing and washing, spray coating, vehicle washing, water misting and water fountains.
|
|
Silvent294
SILVENT 294: nozzle mounted on a Flexarm for applications that require continuous resetting or adjustment of the blowing angle. The Flexarm is supplied complete with a magnetic base. Otherwise, same performance as 920 A.
Air Nozzles
* closeblowing force 0 - 6 N (0 - 1.3 lbs)
o MJ4
o MJ5
o MJ6
o 209 L
o 512
o 011
o 701
o 811
o 921
o 961
o 971
o 209
o 700 M
o 1011
o 920 A
* openhigh blowing force 6 - 130 N (1.3 - 28.7 lbs)
o 973
o 703
o 404 L
o 2005
o 705
o 705 L
o 707 L
o 407 L
o 710
o 412 L
o 715 C
o 715 L
o 720
o 730 C
o 735 L
* openair knives & air curtains
o 366
o 396
o 378
o 306 L
* openspecial
o 910
o 915
o 952
o 453
o 464
o 475 L
* openaccessories
|
|
|
Choose from FJ and FJP FoamJet® nozzles designed to reduce chemical use and produce long lasting foam. Or consider our QuickJet® FoamJet nozzles that are ideal for use on headers when overlapping sprays are needed. Plus, QuickJet FoamJet nozzles offer fast and easy maintenance - no tools required.
|
|
SPRAY CHARACTERISTICS:
F-Series spray nozzles produce a flat, fan-shaped spray pattern, with spray angles available from 15° to 110° measured at 40 psi. Spray angles generally increase with pressure, as shown in the capacity table.
TYPICAL APPLICATIONS:
Suitable for a variety of washing and spraying applications.
- Parts cleaning
- Metal washing
- Foam control
- Asphalt spraying
- Gravel washing
- Vehicle washing
- Fertilizer spraying
- Dishwashers
|
|
Aerating water, brine sprays, chemical processing, coil defrosting, dust control, evaporative condensers, evaporative coolers, industrial
washers, roof cooling, spray coating, gas scrubbing and washing, cooling towers, coal washing, degreasing, gravel washing, dishwashing,
foam control, industrial washing and water fountains.
|
|
|
Air atomizing and hydraulic nozzles for evaporative cooling, NOx control, ammonia injection and more. Find out why our high-efficiency FloMax® air atomizing nozzles are quickly becoming the industry standard for gas cooling.
|
|
SPRAY CHARACTERISTICS:
A flat and thin fan-shaped spray with sharp definition on all edges. This spray delivers very high impact over the area covered. The spray is deflected by angle D away from the centerline of the spray nozzle.
TYPICAL APPLICATIONS:
- High Impact Applications
- Metal Wash
- Gravel Washing
- Vehicle Washing
|
|
Air Jets are larger than nozzles and used when a wider area needs to be hit with the amplified air. They are significantly more efficient than nozzles although often use as much compressed air. Their best use is to replace pairs of nozzles that are used for part ejection or for blow-off applications that require greater force than that provided by air knives or air movers. Nozzles are for point use while air jets can fan out somewhat for better continuous blow-off when a row of them are made. Nex Flow air jets are all made adjustable with a lock ring to assure the security of any gap setting. They have a female 1/8" NPT and made lightweight with anodized aluminum.
From Left to right is the Mini Air Jet, then the High Force Air Jet then the High Flow Air Jet
Model 45001 - High Flow Air Jet and Model 45002 High Force Air Jet are physically the same size. The only difference is a larger exit opening for the amplified air flow. The high flow system is used more for cooling and light blow-off while the high force version is sued mainly for heavier blow-off applications.
Model 45003 - Mini Air Jet is the most compact air jet with high force, is adjustable and ideal for tight spaces. This is unique to Nex Flow and there is no equivalent competitive system.
|
|
High pressure flat or solid stream spray nozzles, HP one piece type, guarantee best precision and high impact thank to a special machining and to a special surface treatment for longer wear life.
The orifice is recessed to protect against damage.
Applications: High-pressure cleaning machines; Industrial washing.
|
|
|
For superior spray performance at pressures from 300 to 4000 psi (20 to 75 bar) consider WashJet® nozzles. Option includes quick-connect installation options, tungsten carbide inserts and more.
|
|
SPRAY CHARACTERISTICS:
A hollow cone spray pattern, emerging at right angles to the centerline of the pipe connection. The standard included angle of the spray cone is 70° at 10 p.s.i. At low pressures hollow cone nozzles produce medium size, uniform droplets. At higher pressures finer droplets are produced.
TYPICAL APPLICATIONS:
- Air and Gas Washing
- Aerating, Rinsing and Humidifying
- Industrial Washers and Spray Ponds
- Cooling Tunnels
- Roof Cooling
- Degreasing
- Dust Suppression
- Metal Treatment
|
|
TYPICAL APPLICATIONS
Aerating water, brine sprays, chemical processing, coil defrosting, dust control, evaporative condensers, evaporative coolers, industrial
washers, roof cooling, spray ponds, spray coating, gas scrubbing and washing, humidification, gas cooling, cooling towers, coal washing,
degreasing, gravel washing, dishwashing, foam control, industrial washing and water fountains.
|
|
SPRAY CHARACTERISTICS:
C series hydraulic atomizing nozzles are designed and precision machined to provide a very fine hollow-cone spray using only the liquid pressure for atomizing.
TYPICAL APPLICATIONS:
- Humidification/Moisture Addition
- Evaporative Cooling
- Steam De-superheating
|
|
|
Nozzles atomizers MZ represent the Top of the range of the hydraulic nozzles atomizers. Composed from different components extremely reduced arranges high performances to the maintenance facility. At request may be made hydraulic atomizers at drawing.
|
|
|
930EX Ionised Air Blowers form a unique range of static control products. A Model 930EX Blower has an ionisation head consisting of 2 BASEEFA certified 910EX Static Elimination Bars. The air source is normally a remotely sited, high efficiency fan with air ducting supplied according to the application. The 930EX is available 3 sizes .
|
|
Static Eliminator - Air-Blade Ionizer:
The Standard Air-Blade Ionizer combines the superior designed Standard Air-Blade™ Air Knife with a quality static bar made by Haug, a world leading static control manufacturer. Charges can be eliminated quickly, even over large distances and surface area.
The Standard Air-Blade Ionizer uses a small amount of compressed air for a powerful, and adjustable force with "laminar" flow to eliminate charges in applications where static bars cannot reach or where high speeds are a factor.
Normally the Standard Model RN Haug brand static bar can address most applications. For extremely high speeds and high charges the extra powerful VS model is used. For washdown applications (such as pharmaceutical areas), even a washable model is available at extra cost.
All Haug static bars come with a patented safety connector and fully shielded cable. The power supplies are "repairable" and are so well made, that we offer a two year warranty on them (one year on the bars).
Features:
- Connections on the back or ends
- It flows from end to end (full flow).
- Stainless steel models are available for high temperature and corrosive models.
- Models are designed for easy cleaning and prevention of dirt entering the static bar, minimizing potential damage.
- Patented connectors with the ground intrinsic to the cable design.
- Instant ON/OFF with no moving parts.
- Repairable Power Supply with a two year warranty.
|
|
A SIMCO anti-static bar with airknife combine the effects of air amplification and ionisation to produce a high-velocity ''sheet'' of ionised air (amplification ratio as high as 25:1). This combined effect can be used for static neutralising and dust removal in a single operation, for instance in the automotive finishing, printing, packaging, plastics and textile industries. The airknife is very compact and does not have any moving parts. SIMCO anti-static bars produce an electrical field which causes air molecules to break down into positive and negative ions. These ions are
picked up by the high-velocity airflow produced by the airknife and propelled into the work area where they neutralise the charged surface or product.
|
|
|
Ionizing air nozzles produce a high-velocity ionized air flow which simultaneously cleans and neutralises static charges on parts and materials. The nozzles operate on compressed air and provide a pinpoint ionized air source for being used in critical cleaning and/or static neutralising. Nozzles can be fitted and installed in many configurations to meet specific requirements. SIMCO power units supply the high voltage necessary for operation.
|
|
|
|
Spray nozzles
