|
|
| Products 91 to 120 of 129 |
SPRAY CHARACTERISTICS:
0° F-Series spray nozzles produce a high impact sold stream. Used in situations where maximum impact is required over a very small target area.
TYPICAL APPLICATIONS:
- Metal Washing
- Agitation
- Mixing
|
|
|
|
|
|
N
Fire Protection
Design Features
* Simplicity of design
* One-piece/no internal parts
* Clog-resistant
* Three standard pipe sizes—½", 1" and 1½"
* Male connection
* Factory Mutual, U.S. Coast Guard and Lloyd's Register approved models
Spray Characteristics
* Two spray cones—an outer, wide angle cone and a narrower inner cone—combine to give full cone effect
Spray pattern: Full Cone
Spray angles: 90° and 120° standard
Flow rates: 3.0 to 534 gpm (9.67 to 1720 L/min)
Fire Protection Approved
This BETE high-efficiency spiral was designed specifically with critical fire and explosion suppression applications in mind. These nozzles feature superior performance unequalled by traditional whirl nozzles.
Superior Performance Characteristics
* Sprays composed on droplets 30% to 50% smaller than conventional designs at equivalent pressures
* Extraordinarily large surface area of spray enhances evaporation and cooling
* Rugged, compact design
* Multiple concentric cone spray, unique to spiral pattern, maximizes contact
Superior Fire/Loss Prevention Applications
* Gas wellhead protection
* Safeguarding ship-borne cargo
* Storage tank protection
* Secondary explosion protection in explosive, dusty environments
* Mitigation of HF and other toxic gas releases
|
|
TF
Wide Range of Flows and Angles, Full Cone Nozzles, Hollow Cone Nozzles
Design Features of TF Wide Range of Flows and Angles, Full Cone Nozzles, Hollow Cone Nozzles
* The original spiral nozzle invented by BETE
* Also referred to as pigtail nozzles, corkscrew nozzles and/or helix nozzles
* High energy efficiency
* One-piece/no internal parts
* Clog-resistant performance
* High discharge velocity
* Male connection standard; female connection available by special order
* The TF24-150 is FM approved
Spray Characteristics of TF Wide Range of Flows and Angles, Full Cone Nozzles, Hollow Cone Nozzles
* Wide range of flow rates and spray angles
* Fine atomization
Spray Patterns: Full Cone and Hollow Cone
Spray Angles: 50° to 180°
Flow rates: 0.5 to 3320 gpm (2.26 to 10700 L/min)
(Higher flow rates available)
|
|
|
The design of the tubes of Drying by Atomization DELAVAN, refers of it in the field of the Manufacture of Powder. We to you propose a complete range of Haute-Pression tubes (SDX) and Bi-Fluids (Swirl-Air)
|
|
In any dryer good mixing and efficient liquid-gas contact are of basic importance to assure rapid drying. The height of the dryer system is largely determined by the time required to dry the largest particle produced by the atomizer, while other important parameters are represented by the inlet-air temperature and the properties of the product being processed.
Spray drying has several advantages, the main one being the ability to handle heat-sensitive products such as food and pharmaceuticals. This is due to the fact that the drying process of a drop happens by loosing water on the external layers, and this keeps the inside material in the drop cool or at least protected against excessive heat.
|
|
|
Recent enhancements make our SprayDry nozzle better than ever. New features allow more user configurability, reduced maintenance time, improved wear resistance and more.
|
|
These units are purposely designed items for use in paint spraying and coating applications. Additional special
purpose air assisted tips are also shown for reference.
|
|
Ultrasonic Oscillators offer a new method of atomization. Electric waves are transformed into mechanical oscillations. Within the atomizer, these oscillations cause a regulated thin film of liquid to experience a minute wave action. These oscillations act to shear the liquid into finely atomized droplets.
Generally, Lechler ultrasonic atomizers are suited to atomize liquids that are free of solids and have a viscosity no higher than 50 centipoises.
Typical applications are:
. Air humidifying
. Product moistening
. Injecting gas into liquids and degassing liquidsn
. Adding liquids during stirring and mixing operations
. Medical technology
|
|
OUR RANGE INCLUDES
FULL CONE PATTERN:
Full cone flange connection / full cone vaneless - off line / full cone three piece nozzles / full cone square spray / square spray - large flow / full cone injector nozzles / full cone off line spray / full cone nozzle tips / multiple full cone - standard spray angles / multiple full cone wide spray angle / full cone spiral nozzles / full cone spiral - extra wide angle.
FLAT JET PATTERN:
Flat jet high pressure washing nozzles / flat jet standard flow rates / flat jet large flow rates, flat jet low flow rates / flat jet tips - standard flow / flat jet tips / large flow / dove-tail tips - standard flow / dovetail tips - large flow / flat jet - large spray angles / flat jet - high impact (spoon nozzles). Also pencil jets.
HOLLOW CONE PATTERN:
Hollow cone - wide spray angle / hollow cone moulded plastic nozzles / hollow cone large flow rates / hollow cone - in line spray / hollow cone deflected spray / hollow cone - low pressure nozzles.
|
|
Spraying Systems Co. offers tens of thousands of products, along with an abundance of technical information and problem-solving ideas to help you optimize your spray application. From spray nozzle basics to automated spray systems, it is highly likely that you'll find the products you need. And, in many instances you'll find more than one product that is suitable for your application. If you're not sure which product is best for you, just give us a call, in the U.S. at 1-800-95-SPRAY (outside the U.S. call -630-665-5000) or visit our Web site at www.spray.com. We have hundreds of technical experts that can help you determine which of our over 80,000 nozzles will yield the performance you require.
|
|
Our UniJet spray nozzles allow for quick and easy spray tip replacement. Spray tips can be removed by simply unscrewing the existing retainer cap, removing the existing spray tip by hand and installing the new tip. There's no need to replace the nozzle body.
Some UniJet nozzles are designed for use with compressed air for blow-off and drying applications. TK spray tips feature a round orifice and a large, unobstructed air volume passage with a wide angle, medium-velocity spray. UniJet blow-off nozzle assemblies feature a horizontal slot across the tip of the nozzle and delivers a uniform flat fan pattern.
UniJet spray nozzles are available with a large choice of interchangeable spray tips, body types, sizes, spray angles and spray patterns. Material options include brass, 303 stainless steel and hardened stainless steel. A wide variety of accessories is available. Choose from strainers, check valves, jet stabilizers, adapters, plates, fittings, mounting and cap options and more.
|
|
Loc-Line® Acid Resistant Hose is excellent for rinsing cycles in plating operations.
Acid environments won't corrode the Loc-Line® Acid Resistant Hose because of its polyester composition.
CAUTION: Loc-Line® Acid Resistant Hose is not intended for conveying acids or high pressure applications.
Common Compatability with Polyester Products Acid Resistant Loc-Line® Yellow Color
No Acetone Yes Acids, (Less than 150° F)
No Acids, (Greater than 150° F) Yes Alcohols
Yes Aromatic Solvents No Chlorinated Hydrocarbon
No Bases, Strong No Ethyl Acetate
Yes Gasoline Yes Greases
Yes Hydrocarbons Yes Oils
Yes Salt Solutions No Water (Greater than 150° F)
|
|
SPRAY & SPYRO NOZZLES
They are particularly indicated for depositing glue on a wide space with a minimum thickness. The Spray version nozzle is used for an even spraying of the product, while the Spyro series allows you to obtain spiral-shaped glue strips. Different diameters and air cap shapes give the customer the perfect solution to all gluing problems.
|
|
SC
Cast Metal Alloy, Full Cone Nozzles
Design Features
* Complete line of full cone nozzles made in cast metal alloys
* Internal removable vane
* Male and female connections
* Flanged connections available
* For plastic nozzles, see NC or MaxiPass nozzles
Spray Characteristics Spray pattern: Full Cone with uniform distribution
Spray angles: 60°, 90° and 120°
Flow rates: 1.68 to 2150 gpm (6.25 to 8180 L/min)
|
|
Spin spray applications produces a sharpl edge and is scarcely visible on the substrate. Spray nozzles can dispense less glue on large areas. The size of the applicated glue depends on the hot air pressure.
Offered nozzels are:
* Braas nozzles with 7 or 12 air orifices left or right twisting, some have special wide air orifices from 0,3 to 2mm
* Brass nozzle plates from 0,3 to 1,25mm
* Stainless steel nozzles with 7 or 12 air orifices left or right twisting, some have special wide air orifices from 0,25 bis 1mm
|
|
|
A broad range of accessories necessary to the realization of systems of pulverization. Collars of Assembly Joined Directional Filters Supports of Piping Regulating Connections to Cams of Pressure Reductions Sleeves To weld Body of Tubes Supports of Tubes Fast Couplers Directional Balls
|
|
Strainers to reduce clogging
High-flow self cleaning strainers
Split-eyelet and swivel connectors, ball fittings and couplers to speed installation
Check, shut-off, pressure relief valves and more to regulate flow
Siphon injectors to adjust and lock-in mixture ratios in two-fluid systems
Hoses and magnetic mounting bases for fast, precise nozzle placement
Tank mixing eductor to increase circulation rates of small pumps and prevent settling
Tank wash, air atomizing, air control, QuickJet and UniJet system accessories and more
|
|
Various types of fixed and rotating spray heads are specified in this section and are designed to suit a wide range of
applications and installations.
|
|
Lechler tank cleaning nozzles work without expensive and defectprone remote drive systems. They are self-rotating and driven by the cleaning fluid. Most types are available in stainless steel as well as in numerous other materials, e.g. PVDF.
The ingenious design of the orifices insures a powerful cleaning and low water consumption at the same time.
|
|
Whatever you have to clean, from small containers up to big tanks, Lechler offers for nearly every application a large choice of tank cleaning nozzles.
Lechler tank cleaning nozzles work without expensive and defectprone remote drive systems. They are self-rotating and driven by the cleaning fluid. Most types are available in stainless steel as well as in numerous other materials, e.g. PVDF.
|
|
|
|
|
|
This comprehensive range of tank washing devices have been developed for a number reasons. Primarily this is due to the quest for greater efficiency in all kinds of industrial procedures, but it is also the continuous requirement to assure a constant and higher quality level of product. Environmental considerations are also influential; the need to reduce energy use and the increasing costs involved in the disposal of effluents are also factors. Thus resulting in the need for a cleaning process that produces a totally satisfactory result and is completed using the lowest possible volume of cleaning solution; the right tank washing head can also be energy efficient.
Our range from the classic fixed head to the more sophisticated models has been developed to cope with the most demanding applications. The following basic concepts should be given proper consideration in order to determine the correct washing cycle for each single application, and consequently the most suitable type of tank cleaning device.
|
|
|
|
|
|
Tank Cleaning can be defined as manual or automated. Cleaning can be a simple rinse with water, or cleaning with detergents and chemicals. Or cleaning can refer to sanitizing with cleaning agents that reduce microbial contaminants. No matter what, the end result of effective tank cleaning is the application of appropriate and consistent levels of rinsing, cleaning, or sanitizing at specified intervals. The goal is ultimately to prevent contamination that would alter the safety, identity, strength, quality, or purity of the final product. Spraying Systems Co. manufactures more than 80,000 different spray nozzles and accessories. Included in our line is a large selection of tank washers and tank washing nozzles. As a result, we're more likely to have available a nozzle to suit the needs of your tank washing application. And you can also be assured that the nozzle you select will be the most cost-efficient design possible. Visit our Web site @ www.spray.com for all your tank washing needs.
|
|
URACA%u2019s tank cleaning heads TWK125-1600 are driven by high pressure water. The characteristic features are compact water jet, minimum displacement circle and minimal pressure losses. For use free on hose or via fixed positioning.
- Operating pressure max:1,600 bar
- Recommended flow rate: 30 - 150 l/min
- Displacement circle min. Ø: 125 mm
- Weight: 10.5 kg
|
|
|
The VARITOP® Tanktop System may be equipped on choice with spray balls or rotating jet cleaners always in connection with the same basic components.The connections ( interfaces ) are identical. In contrast to spray balls, where the cleaning effect is achieved by wetting the tank wall, rotating jet cleaners have the advantage of an additional mechanical cleaning effect by the slowly rotating fan-shaped jet and the associated interval rinsing. Optimal cleaning provides highest plant availability and product quality. Tuchenhagen rotating jet cleaners are availabe with function monitoring as an option. Each cleaner, whether a cleaning lance or a jet cleaner, can be adapted to the customers requests. A fixed cleaning lance or a rotating jet cleaner can maintain an optimal introduction length and an optimised spray ball.
|
|
TW
Tank Washing Nozzles, Clog Resistant Nozzles
Design Features
* Clog-resistant spiral design
* Energy efficient; uses less water than conventional designs
* Compact design; fits small openings
Spray Characteristics
* Easy to maintain
* Unique patterns that spray in opposing directions
* See LEM for other tank-washing applications
Flow rates: 3.0 to 163 gpm (11.4 to 260 L/min)
|
|
Twist & DryTM (TD)
Spray Drying, Hollow Cone Nozzles
Design Features
* Patented locking mechanism for quick and easy change-out and maintenance
* Choose TD-K to operate at high pressures for greater yield capacity
* PEEK backup ring with Viton® 90 or Silicone O-rings (for higher temperatures)
* Female-threaded or butt weld pipe connections
* Easy assembly, no special tools required
* Orifice size: 0.034" through 0.157" (0.864 mm through 3.99 mm)
* Interchangeable swirl and orifice discs for variable patterns and flow rates
* More information on the TD-K nozzle
Spray Characteristics:
Spray pattern: Hollow Cone
Spray angles: 50°, 55°, 60°, 65°, 70°, 75° and 80°
Flow rates: 8.94 to 1570 gph (35.3 to 5970 L/h)
|
|
|
Ultrasonic Oscillators offer a new method of atomization. Electric waves are transformed into mechanical oscillations. Within the atomizer, these oscillations cause a regulated thin film of liquid to experience a minute wave action. These oscillations act to shear the liquid into finely atomized droplets
|
|
Ultrasonic Nozzle
Full cone air-atomizing type. Very small drops (smaller than those from any other type of air-atomizing nozzle). High noise level. Uses supersonic air pressure waves to create small drops. Flow rate range: 0.3 - 46 gph.
Spray angle: 15º.
Materials: 303 stainless steel (head), 303 stainless steel and brass (body).
Typical applications: humidification.
|
|
MicroWhirlTM (MW)
Atomizing Spray Nozzles, Misting Nozzles, Fog Nozzles
Design Features
* Outstanding atomization
* Rugged pinless design
* Drip-free performance
* 70 micron polypropylene filter
* Safety wire hole available
* U.S. Patent #7198201
* Minimum operating pressure 100 psi (7 bar)
Spray Characteristics
* Mist at low pressure; fog at high pressure
Spray pattern: Cone-shaped Fog
Flow rates: 0.009 to 0.151 gpm (0.032 to 0.517 L/min)
|
|
Various types of fixed and rotating spray heads are specified in this section and are designed to suit a wide range of
applications and installations.
|
|
|
|
Spray nozzles
