|
|
A meter for delivering low viscosity fluids with a turbine measuring system. Easy to install, in line or at the end of a
delivery pipe, equipped with an easy-to-read, compact screen.
The meter can be installed directly onto the nozzle for
convenient, on-the-spot reading of the quantity delivered.
Thanks to its strong casing and a sealed plug-in electronic card, this sturdy meter can be used in practically all conditions.
The card can be rotated for easy display reading from all angles.
Turbine measuring system.
Reinforced polyamide body.
Polypropylene turbine.
Pulser type signal: single channel,
reed switch.
Electronic card with LCD display:
Partial 5 figures from 0.1 to 99999,
Total 6 figures from 1 to 999999.
Total resetting available.
Flow indication.
Batteries: n. 2 batteries size AAA
|
|
|
A large range of flow meters ideal for hydraulic applications that require a large turndown ratio, high accuracy, and low pressure drop. Range from 1 - 1500 lpm. Pressures up to 480 bar. Pressure test point and additional sensor ports included as standard. Available with 4-20mA, 0-5V or Pulse signal output.
|
|
|
Blancett sanitary turbine flow meters for liquids meet the 3-A standard for C-O-P (clean out of place) and S-O-P (sterilize out of place) procudures. Flow rates to 400 GPM, clamp sizes to 2.5".
|
|
|
Blancett turbine flow meters for liquids are available in pipe sizes from 1/2" to 10" and flow ranges from 0.6-3 to 500-5000 GPM. Blancett turbine meters use high-quality materials of contruction, including 316 stainless steel and tungsten carbide, to ensure high performance in rugged and aggresive environments. Blancett Model 1100 turbine meters offer +/- 1% accuracy and 0.1% repeatability, and they are rated to 350 degrees F (177 degrees C). Uses include secondary oil recovery, semiconductor, food and beverage, and pharmaceutical.
|
|
...disturbance insensitive and long-lived!
The turbine flow sensors of the product line Turbotron are sensors for flow rate measurement or dosing applications for liquids. Through its especially compact type, its very wide measuring range and its convincing precision of measurement, it has an almost unlimited application.
Function
The liquid flowing into the Turbotron is divided by the guiding blades in four split beams. These hit the rotor from four directions and put it in motion. The uniform loading of bearing from four sides causes the forces to cancel themselves out for the most part and wear is reduced to a minimum.
The extremely hard bearing materials, sapphire and hard metal, ensure in addition an extraordinary life expectancy.
The rotor rotation rate is now converted into an electrical pulse signal (frequency):
VTH and VTP are equipped with rotors which are fitted with magnets. A Hall effect sensor recognizes the rotation of the rotor.
VTI has stainless steel pins in the rotor. An inductive proximity switch detects the rotor rotation.
In both cases, a flow-proportional frequency signal (square wave signal) is available.
|
|
|
The Blancett QuikSert In-line Turbine Flow Meter provides the high accuracy and rigorous design of the standard Blancett turbine, but in a wafer-style mounting configuration. With a unique "between-the-flange" design, the need for mating flanges is eliminated, saving installation time and cost, and allowing for limited space requirements.
|
|
Available Temperature Range: -400°F to +350°F
continuous (to +400°F intermittent heat).
End Fittings: MS flared and flanged styles are
recommended. Other types available on request.
Bearing Styles: Ceramic hybrid ball bearings sizes 1¼”
through 12”. Stainless steel ball bearings sizes ¼” through
1”.
Materials: 316 stainless steel standard. Consult with
applications group for corrosive applications. Broad material
list available.
*** Linearity is density-dependent for a given meter.
Consult factory for details.
|
|
Derived from the FSC Series, the F2000 Quad
Series of fl ow sensors utilizes two fl ow transducers
which are 90-degrees electrically out of phase
from each other. With the addition of a second
fl ow transducer, it is possible to monitor fl ow in
both directions. The F2000 Quad is suitable for
up-down counters that can discern the leading
and trailing edges of the quadrature signals.
Current applications include using the F2000 as
a speed-sensing device on mobile equipment.
This bi-directional fl ow sensor can be used as
a governor, sending frequency signals back to
a PLC which enable it to make the necessary
adjustments. Other functions of the fl ow sensor are
in linear applications where accurate positioning
is required.
Quad Series Turbine Flow Sensor
Provides Bi-directional Flow Rate Measurement
Viton
|
|
Low cost.
· Outstanding accuracy.
· Provides wide flow ranges (10:1 to 100:1 turndown ranges available).
· One piece 316/316L S/S Construction for most pressures.
· For use with unique Hoffer high pressure 316/316L or carbon steel mating flange kits,
supplied complete with SAE J429 Grade 8 high yield strength bolts and "O" rings.
· Operate over a wide range of temperatures.
· Sizes 1/4" through 2". Pressure ratings of 3,000, 6,000, 8,000, and 10,000 psi available
for most sizes.
· Larger sizes and pressures available upon request. Contact factory.
|
|
OUTSTANDING FEATURES
· Low cost.
· Outstanding accuracy.
· Provides wide flow ranges (10:1 to
100:1 turndown ranges available).
· Wide variety of process connections
available.
· Wide selection of construction
materials.
· Operate over a wide range of
temperatures and pressures.
|
|
The Hoffer Sanitary Design Turbine flowmeter is accepted as
meeting 3-A Sanitary Standard No. 28-03 for measurement of
process liquids where high sanitary standards are required.
Available in 11 sizes, ¼” to 3” with standard Tri-Clamp™
fittings, covering flow rates for 0.35 to 650 GPM.
|
|
The flowmeter pickup coil senses
the motion of the rotor and converts it
to a pulsing electrical signal which is
of a discrete digital nature. Three
basic pickup types are offered for use
with the MF Series which will satisfy
standard electrical interface
requirements for turbine flowmeters.
|
|
Litre Meter developed the Pelton wheel principle as the best to achieve accurate measurements of low flows.
A single turbine ring size is common to all Litre Meter flowmeters. The turbine rotor is based on a highly efficient 'Pelton Wheel' design. It is available in various chemically resistant materials such as PFA (Teflon)and PVDF. The rotor ferrites are sealed to make them non-wetted parts. Sapphire bearings are offered for maximum chemical resistance as standard. These provide a very low friction mechanically-robust bearing with long life characteristics.
The rotation of the rotor is sensed by an electronic system using the interaction of ferrites in the rotor tips with a pickup coil. No drag is imposed on the rotor which assists in the measurement of extremely low flows. This, coupled with the efficient Pelton Wheel design and low friction bearings gives the meter major advantages. The complete turbine ring assembly can be easily removed with the meter remaining in line if cleaning is required.
|
|
1MX = Magnetic pickup coil with 1” riser on meter body for mounting of
enclosures and electronics.
1MX3/0=Magnetic pickup coil with 1" riser and enclosure Class I, Groups C & D.
PED-CE =PED-CE mark required for Europe requires the operating temperature and
pressure be given and will be marked on the housing.
CE = CE mark required for Europe.
|
|
The Hoffer Sanitary Design Turbine flowmeter is accepted as
meeting 3-A Sanitary Standard No. 28-03 for measurement of
process liquids where high sanitary standards are required.
Available in 11 sizes, ¼” to 3” with standard Tri-Clamp™
fittings, covering flow rates for 0.35 to 650 GPM.
|
|
Flow ranges are 0.6 up to 5,000 GPM, line sizes 1/2" to 10", pressure rating up to 5,000 PSI, standard temperture rating is 300F (consult factory for higher temperature applications) accuracy of +/- 1% of reading.
Please consult the AW Company website for detailed information regarding all available Turbine flow meters.
|
|
Hoffer inline turbine flowmeters are
velocity measuring devices, which is
to say they measure the average
velocity of a fluid flowing through
the body of the meter. See
Illustration 1 for details on the
construction of the Hoffer inline
turbine flowmeter. Mounted within
the body of a Hoffer liquid turbine
flowmeter is a vaned rotor.
|
|
Turbine flow meters are mediate volume transmitters similar to a Woltmann's sailwheel meter. Thanks to extremely rapid response times and high resolution turbine flow meters are perfectly suitable for fast filling systems.
Due to an enormous pressure and temperature resistance turbine flow meters will also be the perfect choice for water torch systems, temperature control units, cooling circuits or painting systems, where the consumption of solvents and di-water needs to be measured.
|
|
VOLUTRONIC® - that means high-dynamic, precise volume and flow measurements, evaluated according to the application - from a simple display unit to an intelligent micro-controller solution.
The basis for all this is the KRACHT gear type flow meter. This flow measure product presents the successful result of our long-experienced engineers. The sophisticated tooth system geometry in connection with application-specific bearings are made for the gear type flow meter being an absolute "All-rounder". The gear type flow meter covers a wide medium range: to go from hydraulic oil to printing ink, from gear grease to water based lacquer. The highly-efficient KRACHT electronics take the signals given by the gear type flow meter and ensures that processes are exactly monitored, regulated and controlled.
For example, in process technology as micro-controller for metering and mixing systems, or as flexible measuring and recording electronics for differentiated applications in test bench technology. KRACHT know-how guarantees functional solutions - standardized and optimized for application.
|
|
Measuring -/switching range 0,08-5 l/min ...40-160 l/min. water
Connection G 1/4...G 1 1/2, flange DN 15..DN 50,
Material brass, st. st., trogamide, polysulfone, PVDF
Max. pressure 6/10/16/100 bar
Max. temperature 80 °C
Accuracy ± 2,5% FS
Relays; option analogue output, counter, batcher,
Digital display
|
|
PLASTIC IMPELLER FLOWMETERS FOR CHEMICALS
These flowmeters have a pulse out. Construction is simple. Rangability is good. Cost is low.
SRP and SRT flowmeters
-3/8 to 1 inch
-5-40 GPM max flows
-20-150 LPM max flows
-TFE or Polypro bodies
-Threaded ports
-High resolution rotors optional
-Ruby bearings
-Very high rangability
|
|
|
The Litre Meter pelton wheel flowmeter was first patented in 1975 and has an established reputation for function and reliability. Flows from 0.004 l/min can be metered up to 28 l/min using our LM series range. Large flowmeters are provided utilising the orifice/bypass principle where a wide flow range is given and the ability to measure low flows is retained. Pelton Wheel flowmeters are suitable for low viscosity clean fluids with variants in all- PFA Teflon for maximum chemical resistance and high pressure types to 2000 bar at the other end of the spectrum.
|
|
What is a PV Meter?
A 'PV Meter' is a flow meter that will HANDLE PROBLEM FLUIDS that damage other meters. The Oilgear PV Meter (Proportional Velocity) will pass sand, grit, stones (up to 0.25" diameter in our smallest meter), bits of wood or rubber, and suspensions that could stop and damage other meters. There are no close clearances, no rotating seals, and no stuffing boxes. This simple design provides little that can go wrong. If something should malfunction, there is a simple field fix without having to remove the meter from the line.
Here's how it works:
The Oilgear PV Meter looks like a short section of pipe, with a rotor and rotor chamber offset and perpendicular to the flow axis. The flow stream, combining the effects of a Pelton wheel and a centrifugal flow turbine drives the rotor. This combination gives a rotor speed PROPORTIONAL to the flow VELOCITY passing through the rotor chamber, over a wide range of flow rates. The combination gives the same performance and small size of a typical axial flow turbine meter, but with the lower speed and higher torque of a typical positive displacement meter.
|
|
Measuring liquids and liquefied gases in the chemical and petrochemical industrie, in the mineral oil industry, in the food and beverage industry and loading systems, especially for high operating temperatures and low viscosities.
Turbine Meter RQ Series 1
DN 10 - 65
PN 16 - 320
flow rates 0,15 - 120 m³/h
accuracy ± 0,15 % over a reduced flow range ( for viscosities of 0,2 %u2013 0,7 mPas )
accuracy ± 0,25 - 0,3 for the standard - flow range ( for viscosities of 0,2 %u2013 0,7 mPas )
operating temperature according to design -196°C to 250°C
for custody transfer admitted
|
|
The Hoffer Sanitary Design Turbine flowmeter is accepted as
meeting 3-A Sanitary Standard No. 28-03 for measurement of
process liquids where high sanitary standards are required.
Available in 11 sizes, ¼” to 3” with standard Tri-Clamp™
fittings, covering flow rates for 0.35 to 650 GPM.
|
|
We are proud that you have selected a Hoffer Turbine Mini-
Flowmeter, the finest precision flow transducer on the market.
The Hoffer MF Series of Mini-Flowmeters are designed to meet the
need for a high quality low flow measurement device for service in
low to moderate viscosity clean liquids and for gas applications.
|
|
Hoffer flow control
Controls turbine flowmeters
Of all the various types of flow transducers available to industry today. None are so universally applicable as turbine flowmeters. They continue to be the most common way to measure flow electronically and have the ability to measure available upon request offering detailed, technical information.
|
|
OUTSTANDING FEATURES
· Low cost.
· Outstanding accuracy.
· Provides wide flow ranges.
· Wide variety of process connections
available.*
· Operate over a wide range of
temperatures and pressures.
· Exclusive use of hybrid ceramic ball
bearings provide superior life.
|
|
Turbine Flow Sensor - Series TF
0-5 VDC Output, Liquid or Gas
|
|
Hoffer flow control
Controls turbine flowmeters
Of all the various types of flow transducers available to industry today. None are so universally applicable as turbine flowmeters. They continue to be the most common way to measure flow electronically and have the ability to measure available upon request offering detailed, technical information.
|
|
|
|
