Control valves

DN: 6, 3, 4 in
Pressure: 1 bar - 12 bar
Temperature: -15 °C - 80 °C

... pilot control allows on-site pressure adjusting. Application of Groove End Pilot Control Pressure Reducing Valve Our Groove End Pilot Control Pressure Reducing Valves ...

DN: 1.5 in - 12 in
Pressure: 1 bar - 13 bar

... Model DTR / DFR, Diaphragm pilot control Pressure Reducing Valve reduces pressure of inlet flow into desired outlet pressure. Pressure Reducing Valve can prevent damage within pipelines due to high pressure. Features ◆ ...

DN: 2.5, 1.5 in
Pressure: 2 bar - 7 bar

... Model HRTL/HRTR, Fire Hydrant Pressure Reducing Valve, function similar to landing valve, attached in hydrant box serve as connector between pipeline and hydrant hose. Our Fire Hydrant Pressure Reducing Valve ...

DN: 0.125, 0.375, 0.5 in
Pressure: 7, 5, 10, 20 bar
Temperature: -20 °C - 84 °C

... Proportional Flow Control Valve consists of PM series driver and FC series proportional flow valve. With an input signal either through analogue or digital, the needle inside the proportional valve ...

DN: 0.125, 0.375, 0.5 in
Pressure: -1 bar - 20 bar
Temperature: -20 °C - 84 °C

... proportional flow control valves provide precise control of air/water flow with the latest technology. Electronic proportional flow control valves use the latest technology ...

DN: 6.4 mm - 35 mm
Pressure: 5.2, 6 bar

... pinch valve is driven by the PM series driver that accept either analogue ( 0-10V or 4-20mA) or digital RS485 modbus signal.

Compatible with tube OD from 2 mm up to 35 mm

What is a Proportional Pinch Valve?
A ...

DN: 10 mm - 100 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C

... remove 4 screws • Box with two end of career – Electromechanical – Proximity NAMUR – PNP Proximity • Pilot Solenoid Valve 3/ 2 and 5/2 way • Robust pneumatic actuator ...

DN: 10 mm - 100 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C

... diaphragm valve has the highest closing forces in the GF Pipping Systems range of pneumatically operated diaphragm valves. It is available with FC (Fail Close), FO (Fail Open), DA (Double Acting) and DA (Double Acting) ...

DN: 8, 10 mm
Pressure: 16 bar
Temperature: 0 °C - 60 °C

... Use To cut pipe systems Fluids Neutral media free of solids and aggressive liquid or gaseous media if the valve components that contact the media are resistant to the service temperature according to the Divatec resistance ...

DN: 32, 50, 40 mm
Pressure: 10 bar
Temperature: -10 °C - 100 °C

... disinfection Mixing thermoregulating actuator with electronics onboard Semiconductor temperature sensor 3-way FFF BRASS ball valve, full bore Remote management with Modbus-RTU protocol ...

DN: 10 mm - 40 mm
Pressure: 16 bar
Temperature: 0 °C - 60 °C

... 2-way FF PVC ball valve, full bore PN16 with connection kit Available with threaded or to-be-glued connections ...

DN: 32, 40, 50 mm
Pressure: 40 bar
Temperature: -20 °C - 50 °C

... limit microswitches internal anti-condensing heating spacer for insulation with manual override thermal break between ball valve and actuator THERMAL BREAK The material of the thermal break is a compound with self-lubricating properties ...

DN: 0 mm - 1.5 mm
Pressure: 0 bar - 34.7 bar

... The needle valve is an adjustable orifice, which can be used to control flow rates, mini-cylinders, nozzles, timing circuits, filling heads, bleed vents, and in many other applications. The adjusted flow remains stable ...

DN: 0.28 mm - 1.4 mm
Pressure: 0 psi - 200 psi

... orifice and check valve. The orifice meters flow in the forward direction, while the check valve permits free return flow. This valve is particularly well suited for control of small ...

DN: 0 mm - 1.4 mm
Pressure: 0 psi - 200 psi

... The Beswick MIL-MV series metering valve contains an adjustable orifice. The orifice meters fluid flow, regardless of flow direction through the valve. The o-ring seals fit to make the valve insensitive ...

DN: 80 mm - 100 mm
Pressure: 16 bar

... description
Butterfly valve with EPDM O-ring, made from UPVC (U-PVC), available in DN80 and DN100 sizes (PN16).

Product details

• Brand: U-PVC Check Valves
• Category: Check Valves
• Type:

DN: 15 mm - 100 mm
Pressure: 10 bar - 16 bar

... Overview
UPVC double union ball valve with adjustable seat and female plain ends.

Product Details

• Type: UPVC Ball Valves
• Brand: U-PVC Ball Valves
• Category:

DN: 15 mm - 100 mm
Pressure: 10 bar - 16 bar

... union UPVC ball valve BVDL13 for fluid isolation, featuring an adjustable seat and BS female plain ends; available in sizes from 1/2" to 4".

Product details

• Brand: U-PVC Ball Valves
• Category:

DN: 0.25, 0.375 in
Pressure: 700 bar

... Inline unidirectional check valve. It blocks the flow in one direction while allowing it to move in the opposite direction Inline pilot-operate check valve: blocks the flow in one direction allowing it to move in the ...

DN: 15 mm - 250 mm
Pressure: 10 bar - 100 bar
Temperature: -60 °C - 350 °C

... The sliding gate control valve type 8021 in reinforced GS3 design with integrated positioner is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can perfectly be handled. ...

DN: 25 mm - 300 mm
Pressure: 10 bar - 40 bar
Temperature: -40 °C - 220 °C

... The ball sector valve type 4040 with pneumatic actuator can be used for almost all on/off and control applications, especially with abrasive, pasty and fibrous fluids. This series is characterised by an extraordinary ...

DN: 15 mm - 50 mm
Pressure: 0 bar - 16 bar
Temperature: -20 °C - 140 °C

... The aseptic right angle valve type 6051 with EHEDG-Certification and integrated positioner type 8049 is perfectly suitable for applications in pharmaceutical and food processing industry as well as in the biotechnology and cosmetics. ...

Pressure: 2 bar
Temperature: 0 °C - 70 °C
Flow rate: 60 l/min

... NIV series multi-channel gradient valves feature multiple 2-way, normally-closed PTFE media isolation valves connected around a central body. This unique design provides significant reduction in internal volume with enhanced ...

Temperature: 32 °F - 230 °F

... check valve flow controls are typically used to control air flow from air cylinders, thereby controlling the speed at which the piston strokes, either while extending or retracting, depending on their ...

DN: 0.125 in
Pressure: 100 bar
Temperature: 32 °F - 230 °F

... The JFC-2A Threaded Flow Control has a maximum operating pressure of 150psig, a temperature range of 32 to 230 degrees Fahrenheit and a 1/8" port. This device also has 10.5scfm airflow adjustable at 100psig. It is a highly efficient ...

DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h

... ALTITUDE CONTROL VALVE This valve controls water level in high level reservoirs to avoid overflow, without any external control system like float control ...

DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h

... EXCESSIVE FLOW VALVE The valve avoids reservoir emptying and flooding dues to casual pipeline failure. The valve is controlled by a differential hydraulic pilot that senses flow speed closing completely ...

DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h

... FLOW CONTROL VALVE The valve controls downstream flow to a pre-set and constant value in order to limit water consumptions and preserve pipeline fill rate or to set a maximum demand ...

DN: 25 mm - 400 mm
Pressure: 0 bar - 10 bar
Temperature: 220 °C

... precise control of the flow rate through concentric Iris® diaphragms (similar to a camera diaphragm). - Energy-saving and low-noise control valve due to its free centric passage. - Maintenance free Advantages - ...

DN: 25 mm - 400 mm
Pressure: 0 bar - 10 bar
Temperature: 180 °C

... Energy saving valve for the precise and economical control at low loss of pressure of liquids and gases that can be either clean or contain particles. For : Air for aeration in wastewater treatment plant Gases Municipal ...

DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C

... DIALOCK® diaphragm valve with stroke limiter and male ends for solvent welding, metric series. The DK DIALOCK® diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The ...

DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C

... Pneumatically actuated diaphragm valve with male ends, metric series. Normally Closed function. The DK diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal ...

DN: 10 mm - 50 mm
Pressure: 10, 16 bar
Temperature: 0 °C - 100 °C

... way DUAL BLOCK® ball valve with female ends for solvent welding, ASTM series with electric actuator 24 V AC/DC “L” ball. FIP has developed a TKD DUAL BLOCK® ball valve to introduce a high reference standard in thermosplastic ...

DN: 0.125 in - 1.5 in
Pressure: 1 mbar - 670 mbar
Temperature: -20 °C - 120 °C

... Vacuum adjustment valves When these valves reach a certain pre-calibrated vacuum degree, they introduce atmospheric air into the circuit to prevent the increase of the set value and to keep it constant. They can be ...

DN: 0.125 in - 0.375 in
Pressure: 15,000 psi

... Description
Ultra-high-pressure needle valve rated to 100,000 psi for extreme environments. Precision-machined stem and metal-to-metal seat provide fine flow control and reliable shut-off for high-pressure test ...

DN: 0 mm - 10,000 mm
Pressure: 20,000 psi

... Product overview
The Hiflux ball-med-20k is a high-pressure ball valve engineered for industrial systems requiring reliable shut-off and accurate flow control. Suitable for both liquids and gases, it can be ...

Pressure: 2.5 bar - 15 bar
Temperature: 0 °C - 60 °C

... Automatic General Valve ensures precision abrasive control and fail-safe shut down of both the blast stream and media flow. The Elcometer AGV Automatic General Valve utilises all the benefits of our ...

... The Elcometer General Valve Conversion Kit converts an Elcometer GV General Valve into an AGV Automatic General Valve. The Elcometer GV General Conversion can be easily installed onto Elcometer GV ...

... RCV4000+. Safe Control Used with a deadman's handle, the Elcometer RCV4000 Remote Control valves have immediate start/stop capability, allowing you ultimate control over the blast ...

DN: 1, 0.75, 0.5 in
Pressure: 400, 350, 500 bar
Temperature: -20 °C - 125 °C

... Pilling-Up directional control valve single or double acting. From 1 to 7 sections, with relief valve and multiple configuration options. ...

DN: 0.75, 0.5 mm
Pressure: 0 bar - 350 bar

... Mechanical valve to control the cylinder’s position. ...

DN: 6 mm - 40 mm
Pressure: 1.5 bar

... range of ball valves with a variety of body and seal material combinations with female thread, male thread or flanged connections. The ball valve dimensions conform to the DIN standard (installation length and connection). Ball ...

DN: 10 mm
Pressure: 0 bar - 40 bar

... range of ball valves with a variety of body and seal material combinations with female thread, male thread or flanged connections. The ball valve dimensions conform to the DIN standard (installation length and connection). Ball ...

DN: 20 mm - 100 mm
Pressure: 1.5, 10, 40, 25 bar

... range of ball valves with a variety of body and seal material combinations with female thread, male thread or flanged connections. The ball valve dimensions conform to the DIN standard (installation length and connection). Ball ...

DN: 0.25, 0.5, 0.375, 0.125 in
Pressure: 0 bar - 10 bar
Temperature: 0 °C - 70 °C

... unidirectional connection, non-return valves, slide valve, quick exhaust valve Flow regulators 041, 042, 043 Unidirectional flow regulator (block shaped) Valves in ...

DN: 10, 7, 8, 12 mm
Pressure: 15 bar
Temperature: 0 °C - 90 °C

... – Various lines for flexible applications – Mini ball valves also with plug connection Operating pressure See table Materials Handle made of PA66 O-ring made of NBR70 Thread Cyl. thread, DIN EN ISO 228 Con. thread, DIN ...

DN: 16 mm

... lever-operated, with position indicator Butterfly valve in action In-line valve VS 16, stainless steel, small flange KF DN 16 The VS und VS C series valves are butterfly-type valves. ...

DN: 8, 6, 4, 10 mm
Pressure: 0.2 MPa - 1 MPa
Temperature: 0 °C - 60 °C

... Industry's First! It enables same control as the cylinder with shock absorber. (Patent no. 5578502) Shock absorber is not required. Two-stage exhaust flow rate adjustment is realized. By using 2nd stage exhaust speed to be as cushion ...

Pressure: 0 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C

... This Exhaust Needle Valve controls the exhaust flow rate. The valve can be attached directly to a solenoid valve. Best suitable in case a cylinder, etc has no sufficient space around ...

DN: 12, 10, 4, 8, 6 mm
Pressure: 0 MPa - 1 MPa
Temperature: 0 °C - 80 °C

... PP (Polypropylene) is applied for the body material to adapt to clean environment. Easy to check sanitary condition. Clear (semitransparent) color used for the resin body makes it possible to check visually the fluid (liquid) inside. All parts ...

DN: 15 mm - 200 mm
Pressure: 16 bar
Temperature: -20 °C - 160 °C

... Weir-type diaphragm valve to DIN/EN with flanged ends, threaded socket ends or socket weld ends, in straight-way pattern; shut-off and sealing to atmosphere by supported and confined diaphragm; body with coating or lining, position indicator ...

DN: 15 mm - 200 mm
Temperature: -20 °C - 140 °C

... position indicator prevents ingress of contaminants. Valve hydraulics without dead volume ensure optimum conditions for high-purity fluids + protection against deposits. Quick identification of valve position The stem ...

DN: 15 mm - 200 mm
Temperature: -10 °C - 90 °C

... Weir-type diaphragm valve to DIN/EN with flanged ends, straight-way pattern, for drinking water installations to DIN 1988, DIN-DVGW-approved for water acc. to test W 270, in compliance with the latest elastomers guideline of the German ...