Machine feet

Load capacity: 50 kg - 150 kg
Diameter: 30 mm - 50 mm

ADJUSTABLE FEET - PRTR Black Thermoplastic. For certain minimum quantities special studs lengths available upon request.

Load capacity: 400 kg - 2,500 kg
Diameter: 25 mm - 125 mm

Material: Black Thermoplastic. Zinc plated steel stud or stainless steel stud. Note: For certain minimum quantities special studs lengths available upon request. Version PRSTA with anchorage. For more technical information you can ...

Load capacity: 1,200 kg - 2,500 kg
Diameter: 80 mm - 125 mm

Gamm presents the new range of articulated feet model PRST. Material: Black Thermoplastic. Zinc plated steel stud or stainless steel stud. Note: For certain minimum quantities special studs lengths available upon request. Version PRSTA ...

Diameter: 58 mm

Leveling foot M12x85x58 For compensating irregularities in the floor up to 5° Fully assembled spindle and base plate Profile finishing: thread in central hole Product attributes - Profile slot - 10 ESD - yes Adjustment ...

Diameter: 12 mm

Leveling foot M12x160x44 For compensating irregularities in the floor up to 5° Fully assembled spindle and base plate Profile finishing: thread in central hole Product attributes - Profile slot - 10 ESD - yes Adjustment ...

Diameter: 6 mm - 24 mm

... spindle can be combined with one plate. The total height of the swivel foot is calculated from the length of the threaded spindle + height of the hexagon + 22.5 mm. (Swivel foot total height = L + L1 ...

Diameter: 40 mm - 60 mm

... plate can be combined with any threaded spindle or ball joint. The anti-slip plate absorbs vibrations and prevents the swivel foot slipping. For matching threaded spindles see K0421. For matching ball joints see K0422.Safety:These ...

Diameter: 80 mm - 120 mm

... special seal on the machine foot's spindle joint prevent dirt from sticking and reduce cleaning times to a minimum. The machine foot is supplied with the 3-A logo.Application:The ...

... Knuckle Foot D60, M12x75, stainless Knuckle Foot D30, M6x45, black Knuckle Foot D60, M12x120, black Knuckle Foot D80, M10x80, black Knuckle Foot ...

Load capacity: 150 kg
Diameter: 39 mm

Special Adjustable Feet Special Adjustable Feet for special requirements. From simple height adjustment to robust machine fastening – the Adjustable Feet from item always offer the ideal solution. Adjustable Feet ...

... vibration-damping element under the machine and insert the stem through the hole (not threaded) in the frame of the machine (fig.1) - Turn the square end of the stem to take the levelling plate in ...

Diameter: 25 mm - 60 mm

BASE Polyamide based (PA) technopolymer with adjusting hexagon, black colour, matte finish. STANDARD EXECUTIONS - LX: zinc-plated steel threaded stem. - LX-S: zinc-plated steel threaded stem, base with screwdriver slot. - LX-AS: ...

Diameter: 25 mm - 50 mm

BASE Glass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. ARTICULATED STEM Threaded zinc-plated steel with regulation hexagon. STANDARD EXECUTIONS - LS.A: without no-slip disk. - LS.A-AS: with ...

... applications including lathes, milling machines, machining centres and conveyor systems. Features and Benefits: The VF mounts are used for leveling and support, it in many applications ...

Diameter: 99, 119, 77 mm

Leveling sets GN 360 are used for leveling and to compensate for any slope when setting up machines and systems. The thread d2 can also be used as a through-hole for attachment from below. The fine thread d3 laws precise ...

Diameter: 24, 12, 18 mm

Stainless steel leveling elements GN 355.2 are used for levelling and adjustment in machines and equipment. They consist of a leveling screw, a socket cap screw with disk and a spherical washer. The leveling screw ...

Diameter: 40 mm - 119 mm

Levelling sets GN 360 are used for levelling and to compensate for any slope when setting up machines and systems. The fine thread allows precise adjustment and readjustment. The levelling sets are available with ...

Load capacity: 300 kg
Diameter: 8 mm

... Threaded Stud, Thread Length - 60.0 mm | 2.362 in Item code: 550095 48 In stock Stainless Steel Socket Mount Leveling Foot has a 50.0 mm | 1.969 in 20° swivel base for mounting machinery or conveyors up to .

F1 is crafted from PA-6 with 30% glass fibre and the F2 product is crafted from PP and metal. The color is black. As for the application, while the F1 model can be positioned in literally any angle needed, the F2 model is perfectly suited ...

Made from Nylon 6 (PA-6), Steel bright Zinc plated Ideal for heavy applications with a load capacity given in column D Integral hexagonal nut allows adjustment under load Screwdriver slot in base enables fast assembly with power tools Feet ...

... thermoplastic, glass bead reinforced. Anti-slip plate thermoplastic elastomer. Version:black. Note for ordering: If the swivel foot plate and the threaded spindle or ball joint are to be supplied assembled, please add ...

Diameter: 30 mm - 50 mm

... Thermoplastic plate black. Die-cast zinc plate blue galvanized. Stainless steel plate bright. Note for ordering: If the levelling foot plate and the threaded spindle are to be supplied assembled, please add the suffix ...

Diameter: 80, 100, 120 mm

... special seal on the machine foot's spindle joint prevent dirt from sticking and reduce cleaning times to a minimum. The machine foot is supplied with the 3-A logo. Application: The ...

The ideal profile system MayTec offers a comprehensive and integrated profile system where profiles can be connected in any way you may require.

The ideal profile system MayTec offers a comprehensive and integrated profile system where profiles can be connected in any way you may require.

The ideal profile system MayTec offers a comprehensive and integrated profile system where profiles can be connected in any way you may require.

Load capacity: 0 kg - 600 kg

... leveling feet Swiveling, leveling adjustable feet to compensate for uneven floors Swivel range : ± 4 ° to 20°. Adjustable foot plate: different shapes possible from diameter 20 mm to 120 mm Material: plastic ...

Load capacity: 0 kg - 900 kg

Adjustable feet in over 20,000 variations - fixed adjustable foot - hinged adjustable foot function: - screw-on (with screw-on hole/with extension arm/through accessories: floor mounting for trapeze ...

Load capacity: 1,000 kg - 2,000 kg

A leveling foot for slightly uneven floors, conductive, with nut DIN 439 (ISO 4035) form B Material Base: Zinc plated steel Threaded rod: Zinc plated steel Pack Quantity 10 pieces

Load capacity: 2,300 lb - 10,000 lb
Diameter: 1 in - 3 in

Tru-Center™ Tapped Leveling Pads Provides a greater surface area where heavy loads are to be applied or where heavy pressures must be exerted on flexible or softer materials. Pad face swivels and aligns with no damage to the uneven surfaces. Picture ...

Load capacity: 2,300 lb - 10,000 lb
Diameter: 1 in - 3 in

Tru-Center™ Threaded Leveling Pads Material: 4140 Finish: Zinc Plated Pad Heat Treat: Rc 36-40 Thread: UNC-2A (Metric: 6g) Available in FixtureProDesign Software and PartSpec CD

Load capacity: 700 lb - 20,000 lb
Diameter: 1 in - 4 in

Material: 1214 Steel Zinc Plated, Yellow Finish ROHS Compliant Non-Skid Material: Neoprene Case hardened, file hard Swivel 10° in all directions Available with non-skid on base

Diameter: 80 mm

Material base, rod, nut and washer in AISI 304 stainless steel, anti-slip device in black NBR rubber. State of supply depending on the version, complete with nut and washer (see table). Characteristics: model with linear design ...

Diameter: 10, 8, 16, 12 mm

Material threaded rod, nut and washer (see tables); Base in reinforced polyamide, anti-slip material in thermoplastic elastomer. State of supply complete with nut, washer and removable anti-slip seal (if provided, see table). Colour ...

Use: to be fitted on the 25x25x1.2 stainless steel tube. Material base in reinforced polyamide, anti-slip material in thermoplastic elastomer, stainless steel rod, reinforced polyamide cap. State of supply complete with nut, washer, ...

Support element with fine thread and base element 6425FB Body and base element, tempered steel, burnished. Spindle and bearing smooth, tempered steel, plasma-nitrided and burnished. Can be used on T-slots and grid plates by means ...

Load capacity: 459 kg - 6,118 kg
Diameter: 76 mm - 230 mm

PRG Jacmount® Adjustable Levelers are designed to make it easy, economical and reliable to set up your machine or system. The patented connection between leveler and levelling stud is permanent, has a high load capacity, ...

Load capacity: 2,294 kg - 7,138 kg
Diameter: 129 mm - 239 mm

PRS Jacmount® Adjustable Levelers are a new development from AirLoc, especially for machines with high dynamic horizontal force. The robustly designed base plate is permanently connected to a pressure plate by means of ...

Load capacity: 2,294 kg - 7,138 kg
Diameter: 129 mm - 239 mm

PRSK Jacmount ® Adjustable Levelers from AirLoc are specially designed for machines which require high dynamic and horizontal force. The leveller with spherical seat top parts are ideal for compensating ground unevenness ...

... large selection of levelling feet, floor plates and the corresponding accessories needed to stabilise or firmly anchor your machine frames, belt conveyors, industrial workstations and much more. All levelling feet have ...

Load capacity: 1,400 kg - 2,800 kg
Diameter: 60 mm - 125 mm

Load capacity: 750 kg - 4,500 kg
Diameter: 25 mm - 60 mm

Our Threaded Rubber Feet are manufactured using a high quality Commercial Rubber or Nitrile and are available in three main variants, these being Tapered, Straight and Octagonal sided bases. Fixed Adjustable Rubber Feet are a popular ...

Diameter: 16 mm - 35 mm

... with screws Click here to view an installation video of these products Commonly Used For: As a foot for heavy furniture As a screw on rubber foot for furniture

Diameter: 38 mm

... ensuring their ability for use with heavier applications such as machinery/conveyors. Coming with an 'articulating base' each foot allows for up to 8° of movement which can adjust for rugged or un-even flooring. As an ...

Diameter: 40, 50, 100 mm

Swivel foot with ESD-capable Anti-Slip-PlateMaterial: Swivel foot: stainless steel Anti-Slip-Plate: ESD-capable rubberColor: Swivel foot: silver glossy Anti-Slip-Plate: blackPackaging ...

Diameter: 60 mm

Swivel foot with integrated cross recess for faster installation Material: zinc-plated steel Color: galvanized Packaging Unit: 10 pcs.

Diameter: 30 mm - 100 mm

Swivel plates for threaded rod with ball head for compensating uneven floors. According to the size with fastening holes (SW02) or without fastening holes (SW01) Material: PA Color: black Packaging Unit: 10 pcs. Extras: Also ...

Load capacity: 400, 550, 650 kg
Diameter: 8 mm - 10 mm

ADJUSTABLE FEET - FIXED BASE ON THREAD Material: Base : PP black Screw : Zinc-plated steel Dimensions : metric Adjustable feet with fixed base on thread Ref. PDA fixed base - PDB : movable base Load : Options : - Standard ...

Load capacity: 400, 550, 650 kg
Diameter: 10, 12, 8 mm

PDB ADJUSTABLE FEET - MOVABLE BASE WITH THREAD Material: Base : PP black - PA black (available for PDB58) Screw : Zinc-plated steel Dimensions : metric Adjustable feet with movable base with the thread Ref. PDA fixed base - PDB ...

Load capacity: 400 kg - 500 kg
Diameter: 8 mm - 20 mm

ADJUSTABLE FEET - SWIVEL THREAD WITH MOVABLE BASE WITH THREAD Material: Base : PA black - PA black glass fiber reinforced (From M16) Screw : Zinc-plated steel or PA black glass fiber reinforced (From M16) Dimensions : metric Adjustable ...

Description Stem is made from steel with a zinc plated finish. Foot is made from plastic. Wrench flats on the stem allow for easy height adjustment. Ball and socket articulation allows the stem to swivel 30 degrees to ...

Diameter: 2 in - 5 in

LPSG-SF15X30-75X4-50 Description Stem is made from steel with a zinc plated finish. Foot is made from plastic and includes 1/16" black rubber anti-slip grip pad on underside. Wrench flats on the stem allow for easy ...

Diameter: 2 in - 5 in

STEEL STEM - HEX Description Stem with hex adjustment is made from from steel with a zinc plated finish. Foot is made from plastic and includes 1/16" black rubber anti-slip pad on underside. Ball and socket articulation ...

Diameter: 25, 35, 40, 50, 60 mm

Materials: High density polyethylene, (HDPE). Surface: Satin. Colour: Black (RAL 9011). Inserts: Zinc plated steel threaded stud, (thread tolerance 6g). SPECIAL REQUESTS: It's possible to supply the inserts with different ...

Diameter: 37, 49 mm

Materials: High density polyethylene, (HDPE). Surface: Satin. Colour: Black (RAL 9011). Inserts: Zinc plated steel revolving threaded stud, (thread tolerance 6g). SPECIAL REQUESTS: None.

Diameter: 32 mm

... . Colour: Black (RAL 9011). Inserts: Zinc plated steel threaded stem with ball joint, (thread tolerance 6g); with milling for adjustment key.