|
|
Primary pressure standard: Deadweight Tester CPB5000
for high precision pressure calibration of pressure gauges, pressure transmitters, pressure switches etc.
Ranges:
- pneumatic from 0.03 to 100 bar
- hydraulic from 0.2 to 4000 bar
Accuracy up to ±0.010% of READING
With integrated priming pump and spindle pump.
Piston-/cylinder-system changeable without tools
Units under test to be mounted by hand without tools
OPTION: Intelligent Calibration Module type IKM
The IKM calculates automatically the needed corrections caused by ambient influences, deviation between computed pressure and real weight of the masses, conversion to other pressure units like PSI, KG/cm² and much more. The IKM shows the user which masses to be placed on the piston to get the requested pressure, and much more...
NEW: Type LDW 1000, low-cost, hydraulic up to 1000 bar / 14500 psi, accuracy ±0.025% of measured value / reading.
|
|
The MPA series is a co-design between SCANDURA & FEM and the I.N.RI.M (Italian National Research Institute of Metrology) with the objective to develop a series of pressure balances operating in liquid media up to 120 MPa.
Two different product lines are available: BLUE and RED
Here below main features of the RED LINE are listed:
- expanded uncertainty up to 0,008% rdg
- liquid media
- different ranges up to 1200 bar
- interchangeability: MPA chassis can be used with any piston-cylinder unit and same mass set
- industrial applications
- easily transportable
|
|
|
The Diaphragm Comparator is a versatile control circuit component for both fluidic and pneumatic signal levels. The comparator performs many functions including those of an analog pressure comparator, an analog pressure repeater and a digital signal isolator. Maximum pressure is 25 PSI.
|
|
MEP, the Scandura electric-pneumatic handheld calibrator, it’s now available with the display embedded. The wide display allows simultaneously to visualise the:
reference pressure value and the related measurement units
transmitter’s output during a calibration (0 ÷ 25 mA)
voltage input signal (0 ÷ 30 V d.c. )
switch status (ON – OFF)
and it can feed also a current loop at 24 Vcc.
Connecting a PDA (with as PalmOS™ sw) to the instrument, by the serial interface, it’s possible to manage the complete calibration cycle till the printing of the reports.
The required software to manage the PDA is supplied into the standard package of the instrument.
Alternatively to the PDA, the device can be connected to a PC by a serial interface unit, so that every terminal can be used. Ranges from 60 mbar up to 700 bar.
|
|
Newton is the new Scandura solution for the calibration of pressure and electric devices: transmitters, pressure switches, recorders, controller, manometers, indicators, positioner and converters.
The main features are:
- pressure ranges from -900 mbar up to 700 bar.
- vacuum and pressure generation up to 21 bar
– two channels for the electrical signals
– frequency measurement
– 24 V d.c. to feed the transmitter
– interface to PC through RS-232
– 3 readout visualization
– error calculation
– data storage
– selectable engineering units
– logging function
|
|
Digital pressure calibrator HM38
Two individual pressure measuring ranges for gauge, vacuum and differential or absolute pressure
Measuring media: instrument air, inert gases, media compatible sensors available for aggressive / fluid media
11 different selectable measuring units
Datalogging function and RS 232 interface
To measure and generate simultaneously current and voltage
Leak rate, record, ramp, deviation, simulation and trigger function
Incl. free of charge SCS certificate
|
|
The MPA series is a co-design between SCANDURA & FEM and the I.N.RI.M (Italian National Research Institute of Metrology) with the objective to develop a series of pressure balances operating in liquid media up to 120 MPa.
Two different product lines are available: BLUE and RED
Here below main features of BLUE LINE are listed:
- expanded uncertainty up to 0,005% rdg
- liquid media
- different ranges up to 1200 bar
- built in Electronic Card for the errors calculations and the measurement of the ambient parameters
- automatic motor rotation drive system for the masses
- digital mass identification system through bar-code
- Interchangeability: MPA chassis can be used with any piston-cylinder unit and same mass set
|
|
Air reference dead-weight tester BL1R Oil reference dead-weight tester BL1H
Fields:
- Chemical and Petrochemical Industry
- Food and Beverage Industry
- Pharmaceutical and Biotechnical Industry
- Heating, Ventilation and Air Conditioning
- Machine and Process Industry, Power Plants and Distribution, Automotive Industry
Type: BL1R, BL1H
Application: Calibration of pressure monitoring systems
|
|
Model : HCK
Calibration : 70...700 bar
Other features : available with PC6 PRO
|
|
The Fast, Portable, Low Cost, Easy-to-Operate, Gauge Calibration Solution.
- self contained precision hydraulic pressure comparator for the calibration of pressure gauges rated up to 700 bar or 10,000 PSI
- with a simple turn of the handle, it takes less than ten minutes with 5 to 10 test points
- comparator can be filled with water, oil or isopropyl alcohol allowing for clean and safe calibration of almost any type of gauge
- can be used without fluid and FastCalXP 2.0 to calibrate DP transmitters to 300 inches of H2O
- faster to use than a deadweight tester or an automated pressure controllers but costs much less
- ideal to calibrate low cost gauges that are overlooked for ISO9000 compliance
- can be bench mounted
- light weight, compact and portable
- unique design eliminates damage to mechanical pressure gauges
Pressure is Our Business!
|
|
Hydraulic pressure source for pressure calibration:
Pressure Comparison pump (spindle pump) LSP
for comparison pressure calibration
Pressure generation up to 1000 bar / 14500 PSI
Two pressure ports (1 x for reference unit, 1 x for test item)
Generates pressure up to 1000 bar with very few force. Fine adjustable.
Other availavel ranges (LSP): 1600 bar, 5000 bar and 7000 bar.
|
|
Why carry a toolbox of gauges and modules? When a Crystal 30 series calibrator can do the whole job!
- small enough to fit in your shirt pocket, everything is built in
- aluminum case and stainless steel sensors make it very tough
- gas or liquid compatible
- Calibrate to full vacuum and high pressure up to 5000 PSI (300 bar)
- accuracy of 0.05% of reading, laboratory accuracy to outdoor field conditions
- calibrated in an environment chamber, duplicating field conditions
- intrinsically safe:
CSA: Exia, Class I, Division 1, Groups A, B, C, D, T4
ATEX: II 2 G EEx ia IIC T4
- 9V battery provides 90 hrs of operation
Pressure is Our Business!
|
|
Intrinsically Safe Pressure Calibrator 718Ex
- Built-in pressure/vacuum hand pump, with vernier and bleed valve, Pressure measurement to 0.05% of full span, using an internal pressure sensor, Pressure measurement to 200 bar using any of the 8 intrinsically safe 700PEx Pressure Modules, Wide range of selectable measurement units for pressure, Pressure switch test funktion, Min/Max hold functions
Also available as a standard non-Ex unit!
Intrinsically Safe Pressure Module 700PEx
To measure a wide range of pressure in an explosive endangered area the range of pressure modules is extended with 8 ATEX compliant modes. These models are compatible with the ecom 718Ex intrinsically safe pressure calibrator and the intrinsically safe multifunction process calibrator 725Ex.
Also available as a standard non-Ex unit!
|
|
Model : PCK
Calibration : -1...35 bar
Other features : available with PC6 PRO
|
|
|
The FlowAnalyser PF-300, PF-301 VAC & PF-302 LOW are highly accurate testing devices, which bi-directionally measure flow, pressure, temperature, humidity and O2 concentrations.
|
|
Pneumatic calibrator PK with panel manometer PM
Panel Manometer PM
Electronic and Pneumatic Calibration and Control System
Portable simulation and measurement unit (PK) (can be installed into a 19" laboratory system)
Gauge and vacuum can be generated and regulated with the pneumatic unit
Easy exchangeable measurement range (PM22, PM28)
Measuring media: instrument air, inert gases, media compatible sensors available for aggressive /fluid media
12 different selectable measuring units
Hold function
Datalogging function and RS 232 interface
Measurement for leak rate and tendency
Minimum /maximum values
Incl. free of charge SCS certificate
|
|
JOFRA DPC-500 PRESSURE CALIBRATOR
Portable and still efficient like a laboratory instrument
With the high resolution, compact JOFRA DPC-500 documenting pressure calibrator new standards are reached within pressure calibration. Designed for high precision calibration of pressure instruments such as pressure gauges, transmitters, digital manometers, pressure switches and overpressure valves, the DPC-500 offers improved pressure accuracy (± 0.025% FS), better electrical current (± 1.6 ìA) and voltage (± 0.5 mV) accuracy and an extended pressure range of 250 mbar to 1000 bar FS. The DPC-500 also offers absolute pressure measurement from 0.4 to 16 bar absolute.
|
|
CrystalCalXP is a calibration lab in a box! This portable gauge and transmitter calibration system is 7 to 10 times faster than a deadweight tester. It eliminates typing and reduces calculation errors. It is specified at 0.1% of Reading accuracy up to 10000 PSI (700 bar) when using Crystal's XP2i digital pressure gauge as reference or at 0.05% of Reading accuracy up to 5000 PSI (300 bar) when using Crystal's 30 Series calibrator as reference. It has an easy to use wizard-based setup. It comes with a weather-proof rolling case that can be used as a portable bench. Weighs just 16 kg/35 lbs.
Watch demo at www.crystalengineering.net/fastcalxp
|
|
Aeronautical pressure controller/calibrator
The DPI 515 precision pressure controller/calibrator, when supplied with this option, enables direct calibration of aeronautical gauges/instruments for altitude or airspeed. The accuracy for altitude is RVSM compliant. In addition, all of the standard DPI 515 functions are available.
The latest measuring and control technology is incorporated in one compact, functional instrument. Multiple processors, advanced software and a large area display are among a host of features that make the DPI 515 the most flexible controller in the market, with simplified operation and reduced maintenance.
Ranges to 910 knots / 80,000 feet
Precision to ±0.17 knots / ±3 feet
RS 232 and IEEE 488 communications
12 month measurement stability
Multilingual
Control of Altitude in feet or metres
Control of Airspeed in knots, KM/hr, mph or mach
Rate of climb entry in units/min or sec
|
|
PASCAL LAB – P, touch-screen high accuracy pressure calibrator for lab applications:
- modular configuration: up to 4 internal pressure sensor
- connector for external sensors
- uncertainty up to 0,01% f.s.
- ranges: vacuum up to 1000 bar
- display touch-screen with 4 variables simultaneously indicated
- huge memory, bi-direction and real-time communication to PC
- large memory storage for the calibration procedures, data and reports
|
|
Characteristics:
- Continuous simulation of Pt100-Signals with a direct high resolution digital-display and temperature measuring
- Simultaneous measuring of signals and simulation of current and voltage signals
- Simulation from current signals and 2-wire-transmittersignals
- Pneumatic check devices with electronic pressure measuring and handpump for simulation of pressures
|
|
|
From small pneumatic 'bicycle' type pumps to a hydraulic pump that generates up to 15,000 psi (1,000 bar). These are durable pumps with features such as vernier valves, vent valves, manifold connections and swivel fittings, making the pumps ready for your calibration applications.
|
|
Beamex's calibration accessories complete your investment into calibration equipment. Utilizing calibration accessories means an ability to extend configuration possibilities. For instance, by using the external pressure modules you are able to calibrate a wide pressure range with one calibrator.
|
|
|
|
|
|
HTP1 Pressure Test System
1000 bar, 15 000 psi Hydraulic Pressure (compatible with most fluid media) HTP1-700 and HTP1-1000 are lightweight, easy to use and can generate pressures up to 700 bar / 1000 bar, 10 000 psi / 15 000 psi. HTP1 is well suited for calibrating pressure transmitters, pressure transducers, pressure switches and pressure gauges.
Features & Benefits:
Hydraulic Pressure up to 700 bar / 1000 bar, 10 000 psi / 15 000 psi!
Sealed Construction - NO LEAKS ! NO RUST !
Lightweight, hand held and easy to use.
Optional over pressure protection system (via adjustable relief valve)
Quick priming and pressure generation using scissor action pump.
High pressure / priming selector.
Fine adjustment control.
Pressure release valve.
Large see-through reservoir with a capacity of over 100cc.
Compatible with many different liquids. e.g. mineral oil, distilled water. ('Skydrol' / Brake fluid option also available).
Optional accessories include a carrying case, a set of adaptors and a flexible hose with quick fit connectors suitable for many applications.
|
|
Calibration Hand Pumps (Pressure & Vacuum)
Types 2911, 2941, LPP 30, LPP 700 and LPP 1000
LPP 30:
Pneumatic up to 35 bar, switcheable to vacuum -0.95 bar
LPP 700 and LPP 1000:
Hydraulic up to 700 resp. 1000 bar
Together with our electronic pressure calibrators you get a "calibration laboratory" in a case.
All Calibration Handpumps supplied with test tube.
|
|
Scandura has a complete line of pressure/vacuum generators
PNEUMATIC LINE:
- series BA, vacuum up to 7 bar
- series GPP, vacuum up to 40 bar
HYDRAULIC LINE :
- field use: GHM series, ranges up to 300, 400 e 700 bar
- lab use: GHH, series, ranges up to 700 bar
Scandura’s BA series Pressure Generators play their role at the optimum level.
Its high performances are associated with an excellent price to performance ratio, including long terms performance stability and operating reliability as the market leaders only can ensure.
For large quantity supplies Original Equipment Manufacture (OEM) Agreements are possible with any Distributor/Provider of and Maintenance Process Control Equipment
What are you waiting for, surf in our web-site, visiting the incredible Scandura world!
|
|
|
|
|
|
The hand pump with fine adjustment is a pneumatic compression device for a pressure output from 0 to 16 bar and is operable by hand.
The hand pump is especially suitable to check or to calibrate pressure measuring instruments, as for example load cells, pressure sensors and gauges. The pump is portable because of its compact construction and is to serve handily and easily. A fine automatic controller at the pump enables a fine regulation of the pressure output. The pressure pump was developed for a fast and simple pressure calibration.
The hand pump consists of a cylinder, a piston, a pressure release valve, a fine adjustment and the handles. Over the two available internal threads the pump can be attached to the test normal and the test sample, in order to check or calibrate. The handles have to be pressed and released by hand a few times. As result an initial pressure within an area from 0 to 16 bar or -780 to 0 mbar is produced.
Connect test normal and the instrument which is supposed to be calibrated with the pump by using the flexible hose and the supplied connections. During inflating you close the opening valve in clockwise direction. For pressure relief you turn the opening valve against clockwise direction. Before the calibration of the pressure measuring device each connection should be checked for tightness. After the calibration make sure that the pressure is relieved before unscrewing the instrument (otherwise danger of injury exists).
|
|
For comparison calibration of pressure measuring instruments, in the field, but also in workshops and laboratories.
The LPP-KITs consists of a pressure/vacuum source (calibration hand pump LPP 30) and a high precision reference pressure measuring instrument, supplied in a carrying case.
There are several types and models with different accuracies, ranges and features available, see datasheet.
For higher pressure ranges the LPP-Kit comes with the hydraulic calibration handpump LPP 700 or LPP 1000 (up to 1000 bar / 14500 psi)
|
|
Primary standards - Pneumatic deadweight testers - Hydraulic deadweight testers - Digital pressure calibrators -Dial gauge comparators - Digital handheld test systems - Pneumatic and hydraulic pumps
Convenient electronic systems ranging from -1 to 700 bar (25 inHg to 10,000 psi) - multiple choices of pressure ranges, pumps, and accuracies, fully temperature- compensated for problem-free and accurate field use.
|
|
Introduction
Beamex's range of portable MC-calibrators for field calibration is known for their accuracy, versatility and also for meeting both high and uncompromised quality standards. Accuracy is assured when you decide to buy any of Beamex's portable MC-calibrators, because they all come with a traceable, accredited calibration certificate.
Benefit from using Beamex calibrators:
* Very high accuracy
* Simple to use
* All-in-one functionality
* Robust casing
* Customization possibilities
* Extensive after-sales services
|
|
|
|
Pressure calibrators
