|
|
ASTRO stepping motor SAM
- different designs
- permanent magnet-excites
- gradual or continuous enterprise
- high modulation rates
- Precision in the stepper angle
- short starting and stop times
- noiseless run
- high self retaining moment
- sturdily, reliably, long-lived
- Maintenance-free
Stepping motors SAM
2-Phasen
Torque = 3 - 1020 Ncm
Mode of operation = bipolar
Stepper angle = 4-polig for stepper angles of 45°
Full to mini step
Translation with transmission = minute to second step
Self retaining moment = in the dead condition
max. coil temperature = 130°C
Wärmeklasse B
Enclosure = IP40
Braid and terminal container connection
Hybrid stepping motors SAM
2-Phasen
Torques = to 26 Ncm
max. coil temperature = 120°C
Enclosure = IP30
|
|
• Unidirectional and bidirectional
• Power supply specification: from 12 to 230Vac,
12, 24Vdc
• Running torque: from 0,08 to 4 Ncm
• Output shaft speed: from 375 to
8120 rpm |
|
| The 1.8º NEMA 34 High torque motor is available in 2.6”, 3.77” and 5.0” lengths. The motors are capable of holding torque from 310 to 920 oz-in based on unipolar ratings. Unipolar and bipolar windings are available to allow for torque and speed to accommodate your application. The high torque motor provides approximately two times more holding torque than a standard motor of similar design. The size 34 motor can provide high step accuracy as well as high resolution. |
|
Mounting size: 56.4mm, 85mm
Maximum holding torque: up to 9.3Nm
Basic step angle: 1.8°
Protection class: IP65
Marking: CE |
|
For spare parts enquiriesplease see our website.
www.tamagawa-seiki.com/english |
|
3-phase stepping NEMA34 size (90mm)
High Torque
Standard motor with terminal housing
Earth ground connection terminal inside the terminal box
Motor versions also available with:
- Planetary Gear Box
- Leads
- Connector supplier
- Encoder
- Break
- Special winding
etc. upon request
|
|
Schneider Electric Motion 3-phase stepper motors suppliers are extremely robust and maintenance-free. They carry out precise, incremental movements as controlled by a stepper motor drive. A stepper motor drive system consists of a stepper motor and a matching stepper motor drive. Maximum performance of the complete drive system requires the motor and the drive to be perfectly adapted to each other. Depending on the stepper motor drive, the motors can be operated at very high resolutions.
A complete range of options such as rotation monitoring and holding professional brake as well as robust planetary gear units with very little backlash extends the application range.
Schneider Electric Motion 3-phase stepper motors are available in standard and Ex versions (EEx d IIC T4). |
|
For spare parts enquiriesplease see our website.
www.tamagawa-seiki.com/english |
|
Supplier of power supply: 24 V DC
Marking: CE, cUL
With microstep driver.
Standard type
Mounting size: 42 mm and 60 mm
Max. permissible torque: up to 1.66 Nm
High-Torque type
Mounting size: 20, 28 and 42 mm
Max. permissible torque: up to 0.42 Nm
High-Resolution type
Mounting size: 28, 42 and 60 mm
Max. permissible torque: up to 2.3 Nm
Geared types:
Taper hobbed gear: max. holding torque up to 4 Nm, permissible torque 0.2 Nm - 4 Nm, backlash 0.167° - 1°, 5 gear ratios of 1:3.6 - 1:30.
Planetary gear: max. holding torque up to 8 Nm, permissible torque 0.2 Nm - 8 Nm, backlash 0.034° - 0.58°, 6 gear ratios of 1:5 - 1:50.
Harmonic gear: max. holding torque up to 8 Nm, permissible torque 3.5 Nm - 8 Nm, 2 gear ratios of 1:50 and 1:100.
|
|
Presision wrapped rotor
%u2022 Moisture/Dust resistant O-rings
%u2022 Continuous 155°C operation
%u2022 Overtemperature protection thermal switch
%u2022 High voltage insulation
%u2022 Worldwide standard shaft/mounting dimensions
%u2022 Proven reliable suppliers of bearings
%u2022 Cooling kits available to extend torque range
%u2022 Winding potted for high voltage protection and for improved reliabilty
%u2022 Heavy duty continuous operation
%u2022 High acceleration capability
%u2022 Very high torque to inertia ratio
%u2022 Optional holding brakes
%u2022 High energy Neodymium Iron Boron Magnetic design
%u2022 UL/CSA/CE approved
Applications
Material handling, X-Y positioning, textile machines, packaging equipment, centre tool equipment, factory automation, and more.
|
|
JVL offers 4 sizes of high quality, high torque ac servo motors for use with the JVL AMC20 series of advanced AC servo controllers. They range from 400W to 3kW.
The motors offer a wide range of features:
• Highest torque density rating in the industry
• High torque-to-inertia for faster start and stop
• Rugged design and long life bearings suppliers
• Professional encoder 2000p/r. With JVL AMC20 series servo controller, 8000 counts/r with index pulse.
• Very short length compared to power rating
• Standard servo flange
• Yaskawa/Omron flange and shaft
• High axial and radial shaft load
• Low noise
• Option for planetary gear head
• Option for 24VDC brake built in
|
|
Servo system ranging from 10W to 75kW.
AC SERVO MOTOR P1
Capacity :
9 sizes from 0.3kW to 5.5kW
Maximum rotation speed :
3,000 RPM
Use
General industrial machines, machines for precision processing, professional lathe
AC SERVO MOTOR P5
Capacity :
15 sizes from 10W to 1000W
Maximum rotation speed :
4,500 RPM
Use
Professional robot, winding unit, general industrial machine
AC SERVO MOTOR P6
Capacity :
20 sizes from 0.5kW to 75kW
Maximum rotation speed :
3,000 RPM
Use
Robot, general-purpose center tool, and conveyance machine, food processing machine, medical machine, general industrial machine
|
|
AC-servo motors for highly dynamic applications
Design "M.GN series," brushless, permanent excited, three-phase servo motor
Main applications centre tools, textile machines, printing machines
Special applications handling, dosing, winding and paper machines
Performance range with 3000 s/min. / 0.5 - 52 kW
Size 70 - 190 |
|
With a torque range of 0.1 to 70 Nm, serovo motors by ESR cover a wide spectrum of typical servo applications. Standard AC servo motors MR 4 and MR 6 are intended for universal use. Additionally there are the MR 7 motor series with particular high power density; they are mainly used when high torques are needed within compact dimensions. The scope of delivery is rounded off by DC servo motors RS/RX/AXEM for lower powers.
Characteristics of the AC servo motors
- maintenance-free, since brushless
- high dynamics
- wide speed control range
- high power density through rotor with rare earth magnets
- compact servo motors with particular high power density due to improved winding techniques (MR 74, MR 77) or standard servo motors for universal use (MR 4, MR 6)
- ball bearings with grease filling for 20,000 operating hours
- integrated resolver for sinusoidal commutation, optional optical encoders (incremental or absolute, single- or multiturn) for highest dynamics and accuracy
- insulation according to insulation class F, DIN VDE 0530, withstanding tropical conditions
- easy connection of motor and professional encoder using manufacturers of connectors or terminal boxes
- self-cooling, on request cooling through external professional fan motor
- design with flange according to DIN 42 677, installation position as required
- form according to DIN IEC 34 part 7, IM B 5
- industrial bearing plates and housings made of high-quality light metal alloy
- speed of up to 15,000 r.p.m. possible
- rotor dynamically balanced according to vibration severity grade R, on request S
- standard shaft end without groove, special version possible, e. g. with keyway |
|
For positioning applications or position controls as well as dynamic movements we provide a wide range of AC-Servo Drives.
These motors are controlable with our Frequency converter VECTOR in several application.
|
|
Mounting size: 60mm - 90mm
Output power: 6W - 90W
Speed range: 90 - 1400r/min for 50Hz, 90 - 1600r/min for 60Hz
Max. permissible torque: up to 20Nm
Gearheads: 20 different gear ratios of 1:3 - 1:180
Power supply manufacturer: 200 - 230V AC or 100 - 115V AC
Marking: CE, UL and cUL |
|
Mounting size: 60mm - 90mm
Output power: 6W - 90W
Speed range: 90 - 1400r/min for 50Hz, 90 - 1600r/min for 60Hz
Max. permissible torque: up to 30Nm
Gearheads: 20 different gear ratios of 1:3 - 1:180
Power dispenser: 110/115V AC or 220/230V AC
Marking: CE, UL and cUL
|
|
ASTRO synchronous motor suppliers ASM
- starting and direction of rotation-stably
- synchronous, load-independent number of revolutions
- blockierfest briefly
- 1-polig reversable
- high efficiency
- noiseless run
- high self retaining moment
- maintenance-free
Overall lengths
ASM 24/26 = 49mm
ASM 44/46 = 69mm
ASM 84/86 = 109mm
Terminal housing execution = 33mm longer
Engine system
4-polig with 1.500Upm (50Hz), 1800Upm (60Hz)
with 6 pins with 1.000Upm (50Hz), 1200Upm (60Hz)
Rated voltages = 1~24V to 3~500V
Continuous operation S1 (special modes of operation possible)
Self retaining moment in the dead condition
Wärmeklasse B
Coil windings = to 130°C
Ambient temperatures = -15C to 40°C
Enclosure = IP40, IP54, IP55
Basic parts = plastic ones or aluminum pressure pouring
Kind of connection = cable, braid or terminal box connection |
|
saia synchronous motor manufacturer
Dimensions (mm) Ø 36x21
Step angle (°) 7.5/15
Holding torque (cNm) 1.0-1.9.
Detent torque (cNm) 0.22-0.36
Resistance per winding
bipolar/unipolar 6 V (Ohm) 18.5/28
12 V (Ohm) 100/120
24 V (Ohm) 460/500
Gear combination A, D, M, B, F, V
|
|
Details:
- Radially magnetized permanent magnet rotor
- Bobbin Wound coil design
- Sintered bronze bearing specification design - Ball bearing manufacturer optional
- Step angle variation - 3.6 to 20 degree
- Simple motor construction
- Motors wound for operation on AC voltage by using external capacitor manufacturers
Characteristics:
- Windings can be designed for optimum performance
- Long life lubrification
- Simple mechanical construction with proven design characteristics
- Unipolar or Bipolar windings
- High torque size ratio
Advantages:
- Low cost construction
- Ease of use in application
- Simple open loop positioning
- Customization to meet application demands |
|
Tested to withstand twice as many manufacturers of autoclave cycles as many competing motors.
Size 5, 8, and 10
Ideal for medical, food & pharmaceutical, and other applications.
Features include:
-Corrosion resistant stainless steel housings
-High torque-to-inertia and power-to-size ratios
-High energy Neodymium Iron Boron magnets
-Winding temperature ranges from –55º to +220ºC
-Hall Effect devices rated –55º to +150ºC
-Shielded 440C ball bearings supplier standard design/lubrication options available
-Hollow shaft designs for fluid flow-through
-Delivery from stock on standard designs
-Available with gearheads and closed loop control electronics
Customized Autoclaveable Motors
Our motor design experts can help optimize the motor design for your specific application.
Typical applications include:
-Bone cutting devices
-Professional drills
-Orthoscopic shavers
-Reciprocating saws
-Surgical tools
-Reamers
-Ophthalmic instruments
-Dental devices
-Orthopedic and cranial drills
-Cast cutters
-Otolaryngeal tools
-Oscillating industrial saws
-Cataract removal tools
-Implantable pumps and other motorized devices. |
|
Mounting size: 60mm, 80mm and 90mm
Output power: 20, 40 and 90W
Speed range: 100 - 2000r/min
Max. permissible torque: up to 68Nm
Gearheads: 8 different gear ratios of 1:5 - 1:200
Power supply manufacturers: 200-230V AC
Marking: CE, UL and cUL
Constant torque over the whole speed range.
Available types: Round shaft type, parallel shaft gear type, flat gear type. |
|
|
|
Synchronous electric motors: Brushless, Stepper motors, Servo-motors
