... Description
The function of the arc sensor is based on measurements of the welding current. The measurement and correction routines take place during welding and directly compensate for any tolerances that occur. The sensor system does not require ...
Primary current: 4.2 mA
... The Aanderaa Current Sensors are available in a profiling and a single-point version with three depth ratings. We offer Doppler Current Profiler Sensor, Doppler Current Sensor and the In-line ZPulse Doppler Current Sensor. Doppler Current Profiler ...
... WAGO's module signals a value falling below a non-adjustable, asymmetric isolation resistance between +24 V or 0 V of the supply voltage and ground with a potential-free (Iso OK) contact and status LED. The Iso OK contact can be evaluated via a PLC. This ...
Primary current: 0 A - 630 A
... Overview
NEMO SX is a compact measurement module for electrical current monitoring. It provides direct connection with open, flexible Rogowski coils and allows the passage of prong-type supply busbars on the upper side. Supplied with three open ...
... The right solution for every customer. The engine technology is continuously evolving and becoming more and more sophisticated. With the advent of the internet of things, the traditional concept of mobility is evolving towards new models of diagnosis ...
The cold filter plugging point (CFPP) is the lowest temperature at which diesel and domestic heating fuels will pass through a filter in a given time when cooled under certain conditions. CFPP is supposed to give an estimate for the lowest temperature ...
In order to achieve and maintain a consistent product envrionment, constant process parameters are required. For Hot Bar Reflow Soldering, Heat-Seal Bonding, Heat Staking, ACF Laminating and ACF Final Bonding, the most important process parameters are ...
... Magnetic field meter for measuring magnetic direct and alternating fields Three possible measuring ranges: 20 mT, 200 mT and 2000 mT Hand-held unit for operation with mains, battery or power-pack LCD digital display Measuring accuracy: ±2% of measured ...
The fully automatic integrity test unit BECO MAX2 is designed for the regular testing of membrane filter cartridges and determines if a filter meets microbial removal specifications and is correctly installed. The testing result indicates an accurate ...
The MORNSUN Signal Isolation-Isolation Amplifier TR140PWE is designed for precise signal isolation and amplification applications. This signal isolator is suitable for environments requiring programmable features and reliable signal conversion. The device ...
... Mobile PC-allround systems for car, truck, agricultural and construction machinery manufacturers Diverse communication interfaces for perfect integration into the test and production environment Optimized operating and handling concepts Complete ...
... Radiometers and Thermometers The Universal Calibrator (UC) system is used for calibration of temperature in Q-SUN xenon arc testers and irradiance in QUV accelerated weathering and Q-SUN testers. This system consists of irradiance and temperature "smart ...
Parker’s DPS (Display Panel Standard) instrument cluster is an innovative user interface that makes complete vehicle information accessible in a single centralized location. By incorporating the DPS cluster, a wide range of industrial vehicles can be ...
Parker Electronic Controls Division
... Value priced Lightweight and portable Built on Teledyne Benthos proven acoustic release technology System capabilities include: ranging, status, settings, battery voltage, wake up, hibernate, release Compatible with R-Series Acoustic Releases Ideal ...
Teledyne Marine
... • 48-Channel High Performance Strain Gauge Measurement Instrument • Supports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge • 24-bit ADCs, sampling rates up to 25 kSa/s • Built in programmable differential excitation -8V to ...
... Installed in MV/LV distribution substations and LV cut-off cabinets, the SENTINEL Fault Detector range can locate faults on the underground MV network, including single phase grounded faults and multiple phase fugitive and ongoing faults. These detectors ...
... Product Features Monitors a pump's status and detects faults Calculates power and energy consumption Determines a pump's on/off status Records running time and number of starts Acts as input for preventive and predictive maintenance Status Monitoring ...
... Product Description
DCM301B / DCM302B is a 3D electronic compass using a two-dimensional plane calibration algorithm that completes calibration by rotating the sensor plane in place. The device supports hard-iron and soft-iron calibration and ...
Pressure: 0 bar - 2 bar
The MKV 1116 calibration set is intended to be used in conjunction with the SKS 06 (code 231941) or SKS 07 (code 231954) micro-transmitter accessory for calibrating subducts with an ID of 11.4 mm to 16.0 mm. The calibration can be done for single subducts ...
Vetter GmbH Kabelverlegetechnik
... Product overview
Both single ducts and multi-ducts can be calibrated for buried and conduit-protected installations. This calibration unit raises the blow-in capability of mini cables by enabling pre-verification of subduct installation quality.
Compatibility ...
Vetter GmbH Kabelverlegetechnik
Product description: Both single tubes and multi-ducts can be calibrated in buried and in-protection-duct versions. This calibration unit raises the verifiability of mini cable blowability by allowing the quality of subduct installation to be checked ...
Vetter GmbH Kabelverlegetechnik
Voltage: 5 V
... Short description
Calibration bench for simultaneous calibration of JRI digital probes.
Highlights
- Optimization: Up to 96 probes calibrated simultaneously to fully exploit the capabilities of temperature measurement
Voltage: 5 V
... Overview
Calibration bench for simultaneous calibration of up to 24 JRI digital probes. Sends calibration data, coefficients and certificates directly to the JRI‑MySirius application (cloud or on‑premises) via Ethernet (RJ45) or WiFi, with automatic ...
... Magnetic sensors passive sensors, miniature design Material: Housing aluminium. Cable sheath PVC. Version: Compact sensor and plug design. Flat connector, 8-pole, 1x pin. Connection cable, 6-wire, ø 3.55–0.3 mm. Cable bend radius, > 17 mm (static). Note: Works ...
... Hollow shaft sensors with magnetic scanning Material: Shaft stainless-steel. Housing plastic. Cable sheath PVC. Version: Housing black. Flat connector, 8-pole, 1x pin. Cable bend radius, > 17 mm (fixed). Note: For speeds ≤ 600 rpm. Simple assembly ...
The EYE-02 electrostatic charge meter is very compact and lightweight; it measures the electrostatic charge on the surface to be checked without contact and is equipped with an LCD display indicating both the voltage and polarity of the electrostatic ...
2-in-1 XXL calibration board with the pattern for calibrating front camera systems on VW Group vehicles. The newly reworked version in combination with Q.DAS allows users to also calibrate radar systems on all vehicles that require an even reflective ...
... NivuScope 2 measurement system for reliable separation layer detection and sludge level measurement mainly in primary and secondary clarifiers -Interface and sludge level detection independent of density -Indicates the current sludge level ...
... Part-No. 2415(V51 with tapered stainless steel rigid needle. Delivery with protection cover. Part-No. 24155/56 O 4 mm test probe with spring-loaded muttilam. Handle guard chamfered on both sides. Defcvery with protection-cover. Part-No. 24160/61 O 4 mm ...