|
|
|
ANVER Material Handling Vacuum Lifters allow one person to easily and safely handle large loads. Electric-, compressed-air-, battery- or self-powered lifters are available with a wide variety of pad attachments.
|
|
The most advanced manipulator
A rigid manipulation principle is often desirable for eccentric handling (loads that can be handled centrically are best manipulated using a flexible or self-suspended principle such as a cable balancer). The most advanced possibility in rigid handling systems is the Master Balancer: because, in this case too, the arms are bare and hollow. So that manoeuvrability is much better than with conventional manipulators which have drive elements and sometimes even ballast weights on the arms, which means that everything moves. (For technical specifications: see table below)
|
|
Dalmec has already manufactured more than 4000 Manipulators for the car industry, solving the handling problem of:
Axles Gears
Batteries Tailgates
Bottles Bonnets
Headlinings Pedal assembles
Clutch assemblies Radiators
Drive shafts Rear seats
Cylinder heads Side members
Dashboards Body sides
Doors Sunroofs
Engine frames Spare wheels
Engines Steering columns
Exhaust pipes Suspensions
Floor panels Fuel tanks
Flywheels Wheel assemblies
Front seats Wheels
Frontal parts Windscreens
|
|
All solutions FAMATEC are programmed to be prepared in these various configurations, while guaranteeing moreover, the possibility of reconfiguring the solution thereafter during an evolution or of a change of the requirements of the Customer.
The suspended configuration adapts to mediums characterized by a place of limited operation in which there is a need for working under good conditions and in perfect safety
|
|
Pneumatic rope balancers for all types of handling, “weightless”, which allows the minimum effort for the operator for different kinds of parts.
Max capacity 110 kg
Max work radius 7 m
On customer request the following can be supplied:
· Fork liftable self bearing base
· Special handling attachments: mechanical, pneumatic, vacuum o magnetic operated
· Manual or pneumatic rotating or tilting devices
· Jib cranes or light crane bridge or monorails systems, complete with metal supporting frame, delivered as a turn key project
|
|
|
|
|
|
HANDLE YOUR PRODUCTS INTUITIVELY WITH ZE'SOLUTION SAPELEM
ECONOMICIAL
Electric energy.
Eliminate MSD.
INTUTIVE
Follow operators' nature gestures.
No bouton necessary to make movements.
No adjustment necessary to adapt mass changes.
REACTIVE
Reaction time < 0,1 s.
Acceleration up to 1 g.
Max Speed 2 m/s.
POWERFUL
From 0 until 300 kg.
Arm up to 4,7 m.
PRECISE
At Millimeter.
Arm in aluminium : Movements without resistance.
SECURE
Detector of hand presence.
Active security through embedded software.
Power-Cut Management.
ERGONOMIC
Ergo Conception : lightness, sensibility, visibility …
Design for left and right handers.
Effort to make movements < 20 grammes.
ALL PRODUCTS
Cans, boxes, bags, doors, windshields, bumpers, tanks, tubes, bottles, pallets, tyres, ham, spools, eggs, motor parts (water pump, etc.), metallic systems, windows, dashboards, sand core, equipments, moulds, parts of fuselage, yoghurt pots, exhaust system, car batteries, shower trays, sinks, sunroofs, motorbikes engines, bus windscreen, car doors, bonnets, steel cabinets, car seats, aeronautical parts …
ALL FIELDS
Food industry, aeronautics, car industry, textile, cardboard, glass, woodworking, plastic, chemistry, sheet metal, medical, warehouses, electronics, equipments, pharmacy ...
|
|
|
|
|
|
Product
Vacuum-barrels: station of discharge, proportioning and rinsing of barrels and small containers
The vacuum-barrels is designed for the transfer of liquid additives (even viscous) stored out of barrels or small containers and in front of being built-in processes of formulation. It provides the functions of:
- draining of the barrel or container without wasting,
- proportioning of the product,
- rinsing of the barrel and the piping of transfer,
- recycling of the product of washing.
Applications
Industry of the lubricants and chemistry. Adapted more particularly to the cases where:
- the products to be proportioned are numerous,
- the quantities of products to be proportioned are weak (of 10 to a few hundred kilos),
- the necessary precision of proportioning is raised,
- the residual quantity must be reduced.
Strong points
- High Precision and reliability of proportioning.
- Traceability of the operations (recording of the components and connection to the management system of production of the unit).
- Inventory control (indication of the remaining quantity in the barrel).
- Safety, cleanliness and comfort of use.
- Recovery of expensive product and the barrels.
- Reintroduction of the product of washing in the formula.
- Robustness and simple maintenance.
|
|
Dalmec offers a range of tooling heads for handling drums, barrels, containers, pails and canisters in a “weightless’ condition.
Simple to use, they allow the operator to move the product quickly, accurately and with the utmost safety within the working area.
These manipulators offer maximum flexibility in type, design, dimensions and gripping system in order to suit the specific requirements of the user and the environmental conditions of the working area.
|
|
|
|
|
|
HANDLE YOUR PRODUCTS INTUITIVELY WITH ZE'SOLUTION SAPELEM
ECONOMICIAL
Electric energy.
Eliminate MSD.
INTUTIVE
Follow operators' nature gestures.
No bouton necessary to make movements.
No adjustment necessary to adapt mass changes.
REACTIVE
Reaction time < 0,1 s.
Acceleration up to 1 g.
Max Speed 2 m/s.
POWERFUL
From 0 until 300 kg.
Arm up to 4,7 m.
PRECISE
At Millimeter.
Arm in aluminium : Movements without resistance.
SECURE
Detector of hand presence.
Active security through embedded software.
Power-Cut Management.
ERGONOMIC
Ergo Conception : lightness, sensibility, visibility …
Design for left and right handers.
Effort to make movements < 20 grammes.
ALL PRODUCTS
Cans, boxes, bags, doors, windshields, bumpers, tanks, tubes, bottles, pallets, tyres, ham, spools, eggs, motor parts (water pump, etc.), metallic systems, windows, dashboards, sand core, equipments, moulds, parts of fuselage, yoghurt pots, exhaust system, car batteries, shower trays, sinks, sunroofs, motorbikes engines, bus windscreen, car doors, bonnets, steel cabinets, car seats, aeronautical parts …
ALL FIELDS
Food industry, aeronautics, car industry, textile, cardboard, glass, woodworking, plastic, chemistry, sheet metal, medical, warehouses, electronics, equipments, pharmacy ...
|
|
|
|
|
|
HANDLE YOUR PRODUCTS INTUITIVELY WITH ZE'SOLUTION SAPELEM
ECONOMICIAL
Electric energy.
Eliminate MSD.
INTUTIVE
Follow operators' nature gestures.
No bouton necessary to make movements.
No adjustment necessary to adapt mass changes.
REACTIVE
Reaction time < 0,1 s.
Acceleration up to 1 g.
Max Speed 2 m/s.
POWERFUL
From 0 until 300 kg.
Arm up to 4,7 m.
PRECISE
At Millimeter.
Arm in aluminium : Movements without resistance.
SECURE
Detector of hand presence.
Active security through embedded software.
Power-Cut Management.
ERGONOMIC
Ergo Conception : lightness, sensibility, visibility …
Design for left and right handers.
Effort to make movements < 20 grammes.
ALL PRODUCTS
Cans, boxes, bags, doors, windshields, bumpers, tanks, tubes, bottles, pallets, tyres, ham, spools, eggs, motor parts (water pump, etc.), metallic systems, windows, dashboards, sand core, equipments, moulds, parts of fuselage, yoghurt pots, exhaust system, car batteries, shower trays, sinks, sunroofs, motorbikes engines, bus windscreen, car doors, bonnets, steel cabinets, car seats, aeronautical parts …
ALL FIELDS
Food industry, aeronautics, car industry, textile, cardboard, glass, woodworking, plastic, chemistry, sheet metal, medical, warehouses, electronics, equipments, pharmacy ...
|
|
Dalmec offer a wide range of manipulators, fitted with custom-built tooling for the “weightless” handling of various mechanical components.
Simple to use, they allow the operator to move the products quickly, accurately and easily in the operating space.
The type, design, dimensions and picking systems incorporated in these manipulators are tailored to suit the specific requirements of the user and the varying environmental conditions available.
|
|
Pneumatic arm manipulator with pneumatic gripping tool for disks or wheels
180° rotating device, manual operated or by pneumatic motor.
Max capacity 280 kg.
Max work radius 3.7 m.
Max vertical stroke up to 2100 mm.
|
|
|
|
|
|
Compared to the traditional handling devices such as hoists and pneumatic manipulators, the Intelligent Assist Devices by Scaglia Indeva provide relevant advantages:
Precise positioning of the load as they allow for accurate and rapid movements, while traditional handling devices overtravel, bounce and require lots of little corrective movements that reduce productivity.
Intuitive control: It features the “float mode” control or “hands on manipulation”, without actuating the control handle. It makes the most of the natural human ability to coordinate and control motion, thus allowing for a more intuitive control that means a more precise and quicker positioning of the load, especially when this has to be placed in a narrow target as gently as possible.
Improved ergonomics and no effort required. Thanks to the microprocessor based control, the system supplies energy to win inertia both during acceleration and braking.
Speed: IADs respond swiftly, yet smoothly to human touch; the operator notices no time lapse between the machine’s sensing and its response.
Automatic and immediate compensation to weight: it allows handling loads with different weights or loads that vary their weight during handling (emptying out containers) with no stop times at all for turning selector.
|
|
|
ANVER's top-selling systems offer a simple, safe, economical solution to your bag and sack lifting needs. ANVER VT Vacuum Tube Lifting Systems can be configured to handle all load types: porous, semi-porous and non-porous. ANVER offers a free testing service in our ergonomics lab to assist you in determining your load’s porosity and to help you in choosing the appropriate vacuum lifting system.
|
|
Handling attachment with ovalshaped vacuum pad. Indicated for handling of paper, plastic or juta bags.
It is the quickest and economic way to handle bags.
Vacuum generation by electric vane pump.
Max capacity 80 kg.
Accessories: quick disconnection for suction pads, angular adaptor, flexible extended manouvre handle, etc.
|
|
FAMATEC STANDARD gives you the reliability of the solution tested and tuned in many other solutions supplied on similar requests. FAMATEC Standard is characterized by short delivery terms and a precise definition of the technical points since the first steps of the offer.
All the solutions from our brands have as common factors the highest care in details and the will to be recognized as product-leader for the quality of the service offered.
|
|
Pneumatic rope balancers with rotating hook for barrels.
Max capacity 100 kg
Max work radius 7 m
On customer request the following can be supplied:
· Fork liftable self bearing base
· Jib cranes or light crane bridge or monorails systems, complete with metal supporting frame, delivered as a turn key project
|
|
Ball bearing construction
Supports tools weighing up to 10 lbs.
Post, wall, or adjustable height
post mounting
Single or parallel arms
|
|
To analyze the requirement of the customer and to link it with the experiment matured during many years it is essential to decide which technical solution will be the key of success of the project
To direct itself towards a solution with rigid arms means to make it possible to the customer to reach high performances of precision on great ranges or complex movements of the product by guaranteeing a perfect stability throughout all operating cycle.
The flexible solutions exaltent the lightness and the speed of the movements, while making the solution essential for the fast and repetitive operating cycles.
The choice of a solution with rigid arms or a flexible solution is the objective of FAMATEC to satisfy the Customer by providing him the solution most appropriate to its requirements.
|
|
StanleyAssembly Technologies offers vertical balancers, torque tubes and articulating arm systems that balance loads to 277 kg (610 lb) and absorb torque reaction to 1,350 Nm (1000 ft lb). Optional tool holders, end effectors and interfaces enhance movement and orientation for specific applications.
Custom engineered solutions can have higher capacities (to 5,000 Nm) and the capability to integrate arms and balancers with tooling such as multiple-spindle nutrunners. With more than 40 years of experience, Stanley engineers are experts in evaluating customer needs and converting them into solutions that improve the productivity, ergonomics and quality of your manufacturing operations.
|
|
Koike Aronson / Ransome Universal Balance Positioners allow quick and safe manipulation of large awkward work objects, which is critical in maintaining the most efficient down hand welding position. A welder can position objects of up to 4000 pounds by simply applying fingertip pressure and does not need to raise their helmet or break an arc.
The Universal Balance principle is to intersect the rotational axis center of gravity with that of the tilt axis. Work pieces can then be rotated 360? around both axes and, in most cases, around the positioner column. Special engineered positioners are always available.
|
|
Dalmec offers a range of tooling heads for the “weightless” handling of electrical household appliances.
Simple to use, they allow the operator to move the electrical household appliances quickly, accurately and safely throughout the working area.
These manipulators have been custom-built, with specially adapted design, dimensions and picking systems to suit the specific requirements of the users and the various environmental conditions available.
|
|
|
PARTNER PM equipped with special gripping tools, is particularly suitable to manually handle, in a weightless condition, center and off-set loads in any direction. Thus enables the operator to work quickly, with precision and without fatigue, in excellent ergonomic and safety conditions. Its versatile structure also allows to fit in any working environment.
|
|
|
Manipulating ATISmirus 100 with tool to ventose for the movimentazione of scato them in cardboard. The job cycle previews the disattivazione of the parking brakes acting on the appropriate selector. The tool to ventose comes posizionato from the operator on the product to enliven place on the packing emplacement the taken operation of of the product comes executed from the operator acting on the appropriate push-button of taken predisposed on the tool. Caught up a prestabilito value of empty that it assures abundant emergency, the insertion will be had automatic rifle of the balance to cargo. The operator can enliven therefore the cargo easily acting directly on the grip or the product. The release of the product on pallet is obtained pressing the two push-buttons at the same time affixed to you with consequent restoration in automatic rifle of the balance to empty.
|
|
|
|
|
|
The ATISmirus manipulators, with parallelogram shaped vertical movement, allow the handling of loads even with jolts, in any direction without ties, with extreme ease and precision.
They can be integrated with personalized gripping devices, planned and structured according to specific customer’s requests. Such devices are equipped with movement units which can be manual or pneumatic, and are necessary to the movement cycle.
The usability and functionality of the system are obtained by keeping the operator’s needs at the forefront during the planning phase; they are in fact considered by our personnel a fundamental part of the specific characteristics of the movement products.
The parallelogram shaped ATISmirus are available in the following configurations: column mounted installed to the floor, column mounted with self-firmed base-plate, fixed overhead or sliding on overhead runway tracks.
Our manipulators do not need electrical power but only compressed air at 5-7 bar. This implies a remarkable reduction of the installation time simplifying the operation of the set-up of the working area.
|
|
|
|
|
|
The ATISmirus manipulators, with parallelogram shaped vertical movement, allow the handling of loads even with jolts, in any direction without ties, with extreme ease and precision.
They can be integrated with personalized gripping devices, planned and structured according to specific customer’s requests. Such devices are equipped with movement units which can be manual or pneumatic, and are necessary to the movement cycle.
The usability and functionality of the system are obtained by keeping the operator’s needs at the forefront during the planning phase; they are in fact considered by our personnel a fundamental part of the specific characteristics of the movement products.
The parallelogram shaped ATISmirus are available in the following configurations: column mounted installed to the floor, column mounted with self-firmed base-plate, fixed overhead or sliding on overhead runway tracks.
Our manipulators do not need electrical power but only compressed air at 5-7 bar. This implies a remarkable reduction of the installation time simplifying the operation of the set-up of the working area.
|
|
|
|
|
|
The ATISmirus manipulators, with parallelogram shaped vertical movement, allow the handling of loads even with jolts, in any direction without ties, with extreme ease and precision.
They can be integrated with personalized gripping devices, planned and structured according to specific customer’s requests. Such devices are equipped with movement units which can be manual or pneumatic, and are necessary to the movement cycle.
The usability and functionality of the system are obtained by keeping the operator’s needs at the forefront during the planning phase; they are in fact considered by our personnel a fundamental part of the specific characteristics of the movement products.
The parallelogram shaped ATISmirus are available in the following configurations: column mounted installed to the floor, column mounted with self-firmed base-plate, fixed overhead or sliding on overhead runway tracks.
Our manipulators do not need electrical power but only compressed air at 5-7 bar. This implies a remarkable reduction of the installation time simplifying the operation of the set-up of the working area.
|
|
Dalmec offer a wide range of equipment for the “weightless” handling of sheets, various panels, panels of glass etc.
Simple to use, they allow the operator to move the sheets around quickly, accurately and safely.
These manipulators are custom-built and the type, design, dimensions and picking system used is specially adapted to suit the specific requirements of the user and the various environmental conditions available.
|
|
Pneumatic arm manipulators for all types of handling, “weightless”, which allows the minimum effort for the operator for different kinds of parts.
Max capacity 600 kg
Max work radius 3,7 m
On customer request the following can be supplied:
· Fork liftable self bearing base
· Push or powered trolley for suspended execution
· Special handling attachments: mechanical, pneumatic, vacuum o magnetic operated
· Manual or pneumatic rotating or tilting devices
· Rails systems, complete with metal supporting frame, delivered as a turn key project
|
|
Pneumatic parallelogram manipulator Z-Arm
Z-Arm units can be used in the following combinations:
- as mounted on a pillar
- as suspended travelling units
- as suspended stationary units
|
|
|
|
Manipulators, Manipulation arms
