|
|
Laboratory Supplier of test chambers
Temperature and Climatic test chambers
Series VTL and VCL
Compact, quiet, yet powerful units are required to tackle special requirements within limited laboratory space. Also tests are made on smaller specimens - all this directly at the work station.
The VTLand VCL series of temperature and climatic test chambers are ideally suited to such applications.
Test space volumes
34, 64 and 100 l
Temperature range from
+10°C to +180 °C
-40 °C to +180 °C
-70 °C to +180 °C
Humidity range
10 to 98 % RH
Control System:
Controller Board MINCON/32 with Controller Element MINCONTROL
Option Colour touchpanel)
|
|
Range of enclosure of laboratory
Temperature and climatic
Type VTL and VCL
Of compact construction, powerful, especially adapted for a use in laboratory when the place is limited.
Volumes of work
34 liters and 100 liters
Beach of work in temperature
+10°C with +150°C
-40°C with +150°C
-60°C with +150°C
Beach of relative humidity
10 to 98% hr
For more information to consult us
|
|
Environmental simulation chambers for complex alternating climatic profiles
BINDER MKF series:
The MKF series is ideally suited for all tests in accordance with current temperature and climatic test standards based on DIN and IEC standards. The required temperature and humidity values can be attained rapidly and maintained accurately, even under extreme conditions. The unparalleled ease of operation as well as extensive standard features provide that ‘little extra’ in handling.
|
|
Constant Environmental test chambers
series VC 0...
We have designed the VC 0... series especially for the simulation of constant climates.
Test space volumes
190, 335, 600, 990 and 1540 l
Temperature range for climatic tests
+10 °C to +90 °C
Humidity range
10 % to 98 % RH
Calibration values as per ICH
+25 °C / 60 % RH
+40 °C / 75 % RH
The performance range for only temperature tests is wider.
The documentation of temperature and humidity is obtainable via an interface and our optional software S!MPATI or software S!MPATI Pharma (in accordance with FDA 21 CFR, Part 11).
Controll System:
Controller Board M!NCON/32
with removable Colour Touchpanel.
Qualification documentation according to FDA requirements is available.
|
|
Chalmbres of climatic tests for constant climates, range VC 00.
Volumes of tests 190,335,600,990 and 1540 liters
Operating range in temperature with regulation of the relative humidity
+10°C with +90°C
Beach of work in relative humidity
10% to 98% hr
2talonnage with values ICH
25°C/65%hr
40°C/75%hr
Beach of work in temperature without broader relative moisture.
For more information to consult us. |
|
SAL Table Top models 400 L / 1000 L
The unique 400 L salt spray cabinet can be placed either on an existing laboratory table or on the original VLM support. This offers the most convenient and space saving configuration of the cabinet, test solution reservoir and water purification plant. Only compressed air has to supplied. If there is no central plant you will find very low-noise suppliers of compressors among the accessories.
Front door opening professional cabinets allow most convenient loading of the chamber particularly with hanging specimen. Moreover the cleaning of the chamber is easy. Due to the high level of the drain port there will be enough downward slope to the commonly installed siphons.
The side walls of the chamber are made of polyethylene with milled holes for the specimen support. The water trough, the back wall and the inner roof are made of stainless steel coated with Halar® (ECTFE). This unique design allows a quick transfer of the heat into the chamber. Together with the advanced temperature control system best conditions for the precise tempering of the chamber are provided.
For that reason SAL cabinets can also be applied to conducting of high humidity tests after the extension by the working system „CON“. |
|
Ransco Thermal Shock Chambers-RTS
Ransco, a product group of Despatch Industries, has been the innovator in thermal shock testing for 30+ years.
Accelerated life cycle testing
Climatic operating / storage testing
Single or double load capacity
Burn-in
Temperature cycling
Performs to MIL STD 883C
Performs to JESD22
Remote access
Touch screen controls
24/7 reliability
World-side service & support
Our chambers are engineered for today’s demands with maximum throughput, pinpoint analysis, cost effective design, quality construction, versatility and a sleek professional appearance.
Ransco’s vertical design and one piece construction conserves valuable floor space without sacrificing ease of operation. Product is moved from cold to hot zone chambers by a pneumatically operated professional elevator with adjustable transfer speeds. For safety the professional fan, elevator and conditioning systems shut off automatically when the professional door is opened. Uniform horizontal airflow insures proper heat transfer, excellent thermal gradient and the rapid temperature recovery rates critical for maximum throughput and proper test performance. All of Ransco’s systems are equipped with high-efficiency, water-cooled mechanical.
|
|
Environmental simulation chambers for constant climatic conditions
BINDER KBF series:
The KBF series was particularly designed for absolutely reliable stability tests and precise maintenance of constant climatic conditions. It naturally also complies with all applicable guidelines such as ICH, FDA, GMP and GLP, with respect to programming and documentation requirements; with its large reserve capacity and many optional features, it is designed to meet future challenges for many years to come.
|
|
Temperature Supplier of test chambers VT³
und Environmental test chambers VC³
If you are looking for top quality and unmatched performance, then Vötsch has just what you need !
Our completely new temperature and climatic test chambers VT³ and VC³-available in spring 2007- have almost magical control precision.
With S!MPAC* and S!MCONTROL* our revolutionary concept for operation, control and process visibility, these chambers provide features light-years ahead of all others.
Remote control, remote operation, remote monitoring and diagnostics - operation of these chambers is a real joy.
Excellent technical details and many little things make the difference. Absolute safe function of the test chambers, also during high summer temperatures, along with the maintaining of the water quality of the climatic system is guaranteed.
|
|
cold heat Standard VT
cold heat Standard moisture VC
The new generation of climatic chambers enables you to carry out tests according to the national standards and international.
Beach of temperature of -40 °C with 180 °C
and of -70 °C with 180 °C.
Volume of tests: 190,335,600,990 and 1500 L.
|
|
A simple to use continuous humidity chamber to meet the test conditions required by ISO 6270-1. The Elcometer 1200/4 professional tank is made from welded corrosion-resistant polypropylene.
The cover has two sides, each at an angle of 60 degrees to the horizontal. The cover holds 20 test panels, each 150 x 100 mm (5.9 x 3.9").
After being switched on, water is fed in to the unit through the inlet pipe, under pressure (1-5 bar). Once the water is at the required level, it is heated so the temperature of the air above it is maintained at 38°C ± 2°C / 100ºF ± 4ºF. Water vapour then condenses on the panels and trickles off.
|
|
Salt spray alternate climates Standard SC
For tests reproducible of corrosion, in conformity
with the national standards and international, such as DIN, NF, ISO, ASTM, DEF, MIL-STD, etc .....
|
|
Alternatively to our salt spray tests bench top professional cabinets and HD-chest models we offer the most favourable "ECONOMY" chests with 600L and 1000 L chamber capacity. These models are especially designed pursuant to the requirements of salt spray tests according to ASTM B117, ASTM B368, BS 3900 ECCA T8 JIS 7253 DIN 50021 SS, ESS,CASS resp. ISO 9227.
The side- and front walls are made from polypropylene. Following the VLM prinicles the EC-chest model are as well furnished with a ECTFE coated stainless steel bottom. Compared to conventinal chests the EC-chambers show a considerably better heat conductivity. For this reason the chamber will be heated up evenly and rapidly. Moreover due to this benefit, EC-chests can also be used for high humidity tests with constant water condensation pursuant to ISO 6270-2 CH.
The EC-cabinets are furnished with a transparent cover with turnable locks at both sides with a "dry" industrial seal made of silicon foam. Hence, there is not only a convenient cleaning or loading of the chamber with the specimens. More important: As the chamber is hermetically closed during the tests there is no risk of contamination of the lab by escaping salt mist. An air purge is a serial feature and has to be activated before the cover is opened.
|
|
Because there is a need for more rapid evaluations of the resistance of materials to weathering than can be obtained by outdoor exposure tests, devices with artificial light sources are generally used to accelerate the degradation. These sources include filtered long arc xenon, fluorescent, metal halide lamps and carbon arc. Less commonly used light sources include mercury vapor and tungsten lamps. These laboratory accelerated weathering tests are sometimes and perhaps more appropriately, referred to as artificial weathering. Each light source has its own inherent benefits of which a weathering experimenter must be aware.
Typical applications can be found in a variety of industries: textiles, automotive, paints and coatings, plastics and polymers, paper, chemicals and pharmaceuticals. |
|
DSET Laboratories, Inc. pioneered accelerated outdoor weathering in the 1960's with its Fresnel-reflecting solar concentration devices - Emma® (Equatorial Mount with Mirrors for Acceleration) and EMMAQUA® (Equatorial Mount with Mirrors for Acceleration with Water). Economical, proven and continuously improved for even greater accuracy, EMMAQUA is the most widely used outdoor accelerated weathering test method in the world today.
The test apparatus is a follow-the-sun rack with mirrors positioned as tangents to simulate a parabolic trough.
The target board, located at the focal line of the mirrors, lies under a wind tunnel along which a deflector directs ambient temperature cooling air across the specimens. A professional fan aerosol nozzle assembly is employed to spray the specimens with deionized water in accordance with established schedules. Night time spray cycles can be used to keep the specimens moist during the night time hours.
Atlas recommends the exposure of test specimens based on an accumulated dose of ultraviolet radiation measured in MJ/m2. However, test can also be timed on total radiation, Langleys, or real time. The duration can be based on Arizona or Florida radiation equivalents. The UV radiation must be measured as direct beam to avoid errors when evaluating the exposure duration. |
|
Temperature Testing chambers 110/200 l
for the laboratory
VT 4011, VT 7011, VT 4021, VT 7021
Laboratory Scope ...
Temperature test chamber with the ideal performance range for constant and cyclic temperature tests.
All of these extremely compact systems offer a remarkable test space volume. Rapid temperature cycles, high heat compensation and a low noise level make these systems highly favourable for use in electronic and pharmaceutical laboratories. Although these chambers are of a 1-phase design, they are extremely efficient.
The powerful 32-bit control and communication system provides the highest level of operation convenience, with the removable, menu-controlled touchpanel with graphics-capable display.
Test space volumes 110 and 200 l
Temperature range -40 °C to +180 °C and -70 °C to +180 °C
Control System:
Controller Board with removable Colour touchpanel.
|
|
Vibration industrial test systems
Temperature and Climatic Type VTV and VCV
Vötsch vibration test systems enable you to simulate dynamic processes, i.e. mechanical and thermal processes affecting components and assemblies.
Regardless of whether mechanical, hydraulic or electro-dynamical industrial vibrators are required, we cooperate with all well-known national and international manufacturers of vibrators.
The standard range comprises of 36 different types of systems. Special equipment is available and can be customized as required (see special applications).
Test space volumes
600 l, 1200 l and 2200 l
Temperature range
-40 °C to +180 °C and -70 °C to +180 °C
Humidity range (VCV)
10 % to 95 % RH
Temperature rate of change
5 K/min, 10 K/min and 15 K/min (optional to 30 K/min)
Control System:
Controller Board S!MCON/32-NET with removable Colour touchpanel.
|
|
Temperature Walk-In Testing chambers
Series VTZ
Standardized temperature test chambers with test space volumes from 8 to 22 m³ and different performance ranges of -60 °C to +150 °C for environmental tests of large or numerous small specimens.
Accelerated and still reproducible tests as well as temperature tests for the quality control of manufacturing processes are possible.
Control System:
Controller Board S!MCON/32-NET with installed Colour touchpanel.
|
|
| ... products without technical information |
| |
|
|
Climatic test chambers
