Pressure: 0 bar - 400 bar
... Sunfab By-Pass / SBP is an unloading valve for the SAP/SCP pump providing remote switching between idling and operation. The By-Pass valve is used in installations where the power take off is not disengaged during transport. ...
Sunfab Hydraulics
DN: 50 mm - 1,800 mm
Pressure: 10 bar
... indicated by the arrow, intermediate flange valve can be used as end valve. Mounting Flange DIN EN 1092-1, PN 10, ANSI 150 Body material Cast iron GG 25, rust and acid resistant stainless steel 1.4408 Gate valve ...
GEFA Processtechnik
DN: 6, 4, 8 mm
Pressure: 0 bar - 20 bar
Temperature: 0 °C - 140 °C
... Römer flow and stop valve program consists of throttle, shut-off and check valves. The function fittings offer fine adjustment possibilities for the precise regulation of fluid flows. Throttle valves ...
AVS Römer
... Planning, construction and delivery of high quality valves for power plant and process heat generation. ...
DN: 0.5, 1, 2 in
Pressure: 24, 17.2 bar
Temperature: 121 °C
... ”) to mix your fluid to the desired specified temperature exiting the “A” port. In diverting applications where the fluid must be directed from one section of a system to another, the thermal diverting valve ...
DN: 65 mm - 300 mm
Pressure: 0 mbar - 1,600 mbar
Temperature: -15 °C - 60 °C
... VMH Safety shut off valves, slow opening and fast closing with hydraulic or pneumatic actuator The VMH type valve is a safety shut off valve for gaseous media operated by hydraulic ...
... 600° C to 1000° C. Series GD… valves are available with exposed spindle, gear actuated with electrical or hydraulic motors. Series GDH... valves are available with ratchet handle lockable ...
DN: 0.25 in - 0.5 in
Pressure: 0 bar - 210 bar
Flow rate: 0 l/min - 55 l/min
... Variable Flow Control Valves maintain the flow rate of hydraulic fluid to a selected value. Applications include hydraulic cylinders requiring constant extension or retraction speeds ...
Pressure: 400 bar
... Cylinder body made of steel, phosphatized. Remaining parts made of tempering steel. Valve seat and piston are hardened and ground. This valve is leak free. The stop valve shuts the flow from P to A ...
DN: 2 in - 12 in
Pressure: 10, 16, 235, 175 bar
Temperature: 0 °C - 100 °C
... of the pressure reducing valve, the basic valve body and the pressure regulator will automatically close to form a tight seal. If the optional check feature is selected, when the back pressure is generated, the return ...
Taloar
DN: 3.35, 4 in
Pressure: 0 bar - 517.1 bar
Temperature: 0 °F - 250 °F
... Rotary Systems’ timing valve is designed for applications that require automatic clamping and unclamping. This timing valve eliminates the need for a control valve or solenoid valve. ...
Pressure: 420 bar
... Proportional valve 420 bar MWP ¼" port size Static or Dynamic pressure control ...
Pressure: 0 psi - 3,500 psi
... The Cross Model DCV valve is a frame mounted hydraulic depth control valve designed to control two cylinders operating on a common torque tube (rocker shaft). An actuator arm, mounted on the rocker shaft, ...
Cross Manufacturing
DN: 30, 25, 18 mm
Pressure: 6 bar - 420 bar
Temperature: -20 °C - 90 °C
... various manifold valve plate configurations Design characteristics directional control valves available as sub plate mounted valves nominal sizes 18, 25 and 30 modular design for ...
DN: 1.813 in - 7.063 in
Pressure: 15,000, 10,000 psi
... next project, Cameron frac valves provide three times more uptime compared with other suppliers, minimizing NPT and related costs. Choose the gate valve that best suits your fracturing program Designed as a manual ...
CAMERON
... Continental has a full range of stack valves including check, flow control, relief, reducing, sequencing, shuttle valves and counterbalance valves – all manufactured to NFPA and ANSI/ISO standards. Modular ...
CONTINENTAL HYDRAULICS
DN: 0.375 in
Pressure: 10,000 psi
Flow rate: 7 us gal/min
... extended lengths of hydraulic hose. Operation: Controls surges by restricting flow if it exceeds 7 gpm. When flow subsides, valve reopens automatically. Has 3/8" NPTF male end to thread into return port of system ...
... The control valves with actuator are primarily used within the industrial plants to maintain operating conditions such as flow, pressure, temperature and liquid level by fully or partially opening or closing response to signals received ...
DN: 50 mm - 300 mm
Pressure: 10, 16 bar
Temperature: 50 °C
... sealing ring - Independent of variations of the inlet pressure / flow rate, the valve regulates a higher inlet pressure to a constant, lower outlet pressure - Valve controlled by its own medium - Pre-formed ...
VAG-Group
DN: 50 mm - 1,500 mm
Pressure: 400 bar
Temperature: -196 °C - 450 °C
... Trunnion mounted split body ball valves, double block and bleed function, for oil and gas standard and severe applications The FCT Split Body trunnion mounted ball valves have been designed for severe oil and gas applications, ...
Pentair Valves & Controls
DN: 700 mm - 3,500 mm
Pressure: 6 bar - 40 bar
... Epoxy-Polymer-Ceramic (EPC) Tried and tested technology for nominal widths between DN 700 and DN 3600, variants with weightloaded hydraulic actuator available. Drinking water certificate. ...
DN: 56 mm - 188 mm
Pressure: 30 psi - 200 psi
Temperature: 125 °C
... primary source of fuel is taken away. An intake air shut-off valve is a must for diesel engines which have even a possibility of encountering hydrocarbon vapors. The Intake Air Shut-off Valves from AMOT use the best available ...
AMOT
DN: 63, 90 mm
Pressure: 8, 10 bar
Temperature: 10 °C - 60 °C
... • Closing of the valve by diaphragm. • 100% factory tested. • Valve closing is produced when water flows to the control chamber. • The opening is done when the fluid of the control chamber is released ...
DN: 0.375 in
Pressure: 20 bar - 207 bar
... The Series 3000 progressive divider valve manifold distributes and proportions incoming oil or grease to bearing points. A typical divider valve manifold consists of an inlet section, three to ten valves ...
BIJUR DELIMON INTERNATIONAL
... temperature variations. According to customers‘ information, valves are factory adjusted ready for operation and very simple to readjust if so desired. The patented up levelling system combined with compensated pilot ...
Blain Hydraulics GmbH
DN: 40 mm - 70 mm
Pressure: 6, 16 bar
Temperature: -20 °C - 80 °C
... bracket. The light weight aluminium material in combination with our well known butterfly valve design is a very attractive solution for a modern hydraulic system. Download the data sheet or contact us for further ...
DN: 25 mm
Pressure: 0 bar - 350 bar
Flow rate: 0 l/min - 300 l/min
... Series VR5U08 Nominal Size Inch 1" mm 25 Maximum Flow gpm 80 lpm 300 Maximum Pressure psi 5000 bar 350 Mounting Flange ...
DN: 0.125 in - 1.25 in
Pressure: 250, 315 bar
Temperature: -15 °C - 70 °C
... Cetop 3 (NG6) Flow control Valve with Bypass Check – The purpose of a flow control valve is to regulate the flow rate in a specific portion of a hydraulic circuit. In hydraulic systems, ...
YUKEN Europe Ltd.
... the majority of the features of the electro- hydraulic ARV without electronic controls. Product Details The ARV-H provides the core functionality of the industry-standard Olmsted Electro- Hydraulic valve ...
Pressure: 0 bar - 350 bar
Flow rate: 0 l/min - 50 l/min
... pilot operated pressure control valve with electric proportional control and mounting interface in compliance with ISO 4401 (CETOP RP 121H) standards. — It is suitable to modulate the pressure in hydraulic ...
Duplomatic Oleodinamica
DN: 0.25 in - 2 in
Pressure: 255 bar
Temperature: -20 °C - 250 °C
... 2 pièces bail valve 1500lbs forged carbon Steel with full bore for Chemical and Pharmaceutical industries, petrochemical industries, hydraulic installation, heating and compressed air. For fluids at high pressure and ...
SFERACO
DN: 0.25 in
Pressure: 1,000 psi - 5,000 psi
Flow rate: 5 us gal/min
... Valves are adjustable: 1,000 to 5,000 psi Features Pressure reducing valves are designed to reduce the maximum pressure in a portion of a hydraulic circuit: the valve is open from ...
DN: 40 mm - 1,600 mm
Pressure: 2.5 bar - 100 bar
Temperature: -10 °C - 200 °C
... the request of customers . The gate valve body is made of cast steel and it is suitably dimensioned to assure a high safety factor. The thicknesses are always higher than the mini-mum ones established for GATE VALVE ...
DI NICOLA INFINAM
DN: 0.375 in
Pressure: 0.1 bar - 10 bar
Temperature: 0 °C - 60 °C
... The EURO filling valve is the simplest version of our cistern valves and can be used in any standard cistern. ...
DN: 15 mm - 200 mm
Pressure: 16 bar - 420 bar
... Metal-sealed Floating Ball Valve body material: Carbon steel /Stainless steel / Alloy steel /Special ( Monel /Inconel /Hastelly etc.) end connection: RF/RTJ/BW/SW/Thread operation: product overview:Athena metal-seated floating ...
Athena Engineering S.r.l.
Pressure: 25 MPa
Temperature: -40 °C - 80 °C
Flow rate: 220 l/min
... trucks, open hydraulic systems, and single-acting cylinders. It has three functions: lifting, stopping, and lowering. The product is equipped with an adjustable relief valve to achieve reliable protection for the entire ...
Weifang Chengfeiyue Hydraulic Machinery Co., Ltd.
Pressure: 35 MPa
Flow rate: 20 l/min
... DVP6 type throttle stop valve Maximum flow: 20 L/min Maximum working pressure: 35 MPa Applications Environmental sanitation vehicle ...
Hytek Power Co., Ltd.
Pressure: 60 bar - 280 bar
Flow rate: 40 l/min
... - Technical information - Minimum purity of the medium: ISO 4406 19/17/14 (NAS 8) A and B versions with check valve - Height - 40 mm - Pressure range - 60 - 280 BAR - Flow - Max. 40 l/min ...
DN: 0.5 in - 6 in
Pressure: 10 MPa - 76 MPa
Temperature: -29 °C - 593 °C
... standard: ASME B16.34 Valve body material: WB36/A105/F22 Flow characteristics: E%/L Leakage level: ANCI FCI-02 V Product Features 1. - Good valve core stability. The sturdy and durable guide cylinder provides ...
Suzhou Delan Energy Science & Technology Co.,Ltd
the best suppliers